1 files changed, 0 insertions, 105 deletions
diff --git a/doc/README.mpc8315erdb b/doc/README.mpc8315erdb
deleted file mode 100644
index b32132d053..0000000000
--- a/doc/README.mpc8315erdb
+++ /dev/null
@@ -1,105 +0,0 @@
-Freescale MPC8315ERDB Board
------------------------------------------
-
-1.	Board Switches and Jumpers
-
-	S3 is used to set CONFIG_SYS_RESET_SOURCE.
-
-	To boot the image at 0xFE000000 in NOR flash, use these DIP
-	switch settings for S3 S4:
-
-	+------+	+------+
-	|      |	| **** |
-	| **** |	|      |
-	+------+ ON	+------+ ON
-	  4321		  4321
-	(where the '*' indicates the position of the tab of the switch.)
-
-	To boot the image at the beginning of NAND flash, use these
-	DIP switch settings for S3 S4:
-
-	+------+	+------+
-	| *    |	|  *** |
-	|  *** |	| *    |
-	+------+ ON	+------+ ON
-	  4321		  4321
-	(where the '*' indicates the position of the tab of the switch.)
-
-	When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
-
-2.	Memory Map
-	The memory map looks like this:
-
-	0x0000_0000	0x07ff_ffff	DDR		 128M
-	0x8000_0000	0x8fff_ffff	PCI MEM		 256M
-	0x9000_0000	0x9fff_ffff	PCI_MMIO	 256M
-	0xe000_0000	0xe00f_ffff	IMMR		 1M
-	0xe030_0000	0xe03f_ffff	PCI IO		 1M
-	0xe060_0000	0xe060_7fff	NAND FLASH (CS1) 32K
-	0xfe00_0000	0xfe7f_ffff	NOR FLASH (CS0)	 8M
-
-	When booting from NAND, NAND flash is CS0 and NOR flash
-	is CS1.
-
-3.	Definitions
-
-3.1	Explanation of NEW definitions in:
-
-	include/configs/MPC8315ERDB.h
-
-	CONFIG_MPC83xx		MPC83xx family
-	CONFIG_MPC831x		MPC831x specific
-	CONFIG_MPC8315		MPC8315 specific
-	CONFIG_MPC8315ERDB	MPC8315ERDB board specific
-
-4.	Compilation
-
-	Assuming you're using BASH (or similar) as your shell:
-
-	export CROSS_COMPILE=your-cross-compiler-prefix-
-	make distclean
-	make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin)
-	make all
-
-5.	Downloading and Flashing Images
-
-5.1	Reflash U-boot Image using U-boot
-
-	NOR flash:
-
-	tftp 40000 u-boot.bin
-	protect off all
-	erase fe000000 fe1fffff
-
-	cp.b 40000 fe000000 xxxx
-	protect on all
-
-	You have to supply the correct byte count with 'xxxx'
-	from the TFTP result log.
-
-	NAND flash:
-
-	=>tftpboot $loadaddr <filename>
-	=>nand erase 0 0x80000
-	=>nand write $loadaddr 0 0x80000
-
-	...where 0x80000 is the filesize rounded up to
-	the next 0x20000 increment.
-
-5.2	Downloading and Booting Linux Kernel
-
-	Ensure that all networking-related environment variables are set
-	properly (including ipaddr, serverip, gatewayip (if needed),
-	netmask, ethaddr, eth1addr, rootpath (if using NFS root),
-	fdtfile, and bootfile).
-
-	Then, do one of the following, depending on whether you
-	want an NFS root or a ramdisk root:
-
-	=>run nfsboot
-	or
-	=>run ramboot
-
-6	Notes
-
-	The console baudrate for MPC8315ERDB is 115200bps.