diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/README.ppc440 | 13 | ||||
| -rw-r--r-- | doc/README.sha1 | 57 |
2 files changed, 64 insertions, 6 deletions
diff --git a/doc/README.ppc440 b/doc/README.ppc440 index 08f34f589f..2e04abacc8 100644 --- a/doc/README.ppc440 +++ b/doc/README.ppc440 @@ -146,12 +146,13 @@ that maps in a single PCI I/O space and PCI memory space. The I/O space begins at PCI I/O address 0 and the PCI memory space is 256 MB starting at PCI address CFG_PCI_TARGBASE. After the pci_controller structure is initialized, the cpu-specific code will -call the routine pci_pre_init() if the CFG_PCI_PRE_INIT flag is -defined. This routine is implemented by board-specific code & is where -the board can over-ride/extend the default pci_controller structure -settings and do other pre-initialization tasks. If pci_pre_init() -returns a value of zero, PCI initialization is aborted; otherwise the -controller structure is registered and initialization continues. +call the routine pci_pre_init(). This routine is implemented by +board-specific code & is where the board can over-ride/extend the +default pci_controller structure settings and exspecially provide +a routine to map the PCI interrupts and do other pre-initialization +tasks. If pci_pre_init() returns a value of zero, PCI initialization +is aborted; otherwise the controller structure is registered and +initialization continues. The default 440GP PCI target configuration is minimal -- it assumes that the strapping registers are set as necessary. Since the strapping bits diff --git a/doc/README.sha1 b/doc/README.sha1 new file mode 100644 index 0000000000..7992f7fb4c --- /dev/null +++ b/doc/README.sha1 @@ -0,0 +1,57 @@ +SHA1 usage: +----------- + +In the U-Boot Image for the pcs440ep board is a SHA1 checksum integrated. +This SHA1 sum is used, to check, if the U-Boot Image in Flash is not +corrupted. + +The following command is available: + +=> help sha1 +sha1 address len [addr] calculate the SHA1 sum [save at addr] + -p calculate the SHA1 sum from the U-Boot image in flash and print + -c check the U-Boot image in flash + +"sha1 -p" + calculates and prints the SHA1 sum, from the Image stored in Flash + +"sha1 -c" + check, if the SHA1 sum from the Image stored in Flash is correct + + +It is possible to calculate a SHA1 checksum from a memoryrange with: + +"sha1 address len" + +If you want to store a new Image in Flash for the pcs440ep board, +which has no SHA1 sum, you can do the following: + +a) cp the new Image on a position in RAM (here 0x300000) + (for this example we use the Image from Flash, stored at 0xfffa0000 and + 0x60000 Bytes long) + +"cp.b fffa0000 300000 60000" + +b) Initialize the SHA1 sum in the Image with 0x00 + The SHA1 sum is stored in Flash at: + CFG_MONITOR_BASE + CFG_MONITOR_LEN + SHA1_SUM_POS + for the pcs440ep Flash: 0xfffa0000 + 0x60000 + -0x20 + = 0xffffffe0 + for the example in RAM: 0x300000 + 0x60000 + -0x20 + = 0x35ffe0 + + note: a SHA1 checksum is 20 bytes long. + +"mw.b 35ffe0 0 14" + +c) now calculate the SHA1 sum from the memoryrange and write + the calculated checksum at the right place: + +"sha1 300000 60000 35ffe0" + +Now you have a U-Boot-Image for the pcs440ep board with the correct SHA1 sum. + +If you do a "./MAKEALL pcs440ep" or a "make all" to get the U-Boot image, +the correct SHA1 sum will be automagically included in the U-Boot image. + +Heiko Schocher, 11 Jul 2007 |