diff options
Diffstat (limited to 'drivers/ddr/fsl')
| -rw-r--r-- | drivers/ddr/fsl/Makefile | 1 | ||||
| -rw-r--r-- | drivers/ddr/fsl/fsl_mmdc.c | 156 |
2 files changed, 157 insertions, 0 deletions
diff --git a/drivers/ddr/fsl/Makefile b/drivers/ddr/fsl/Makefile index 01ea86217c..00dea428e3 100644 --- a/drivers/ddr/fsl/Makefile +++ b/drivers/ddr/fsl/Makefile @@ -33,3 +33,4 @@ obj-$(CONFIG_SYS_FSL_DDRC_GEN3) += mpc85xx_ddr_gen3.o obj-$(CONFIG_SYS_FSL_DDR_86XX) += mpc86xx_ddr.o obj-$(CONFIG_SYS_FSL_DDRC_ARM_GEN3) += arm_ddr_gen3.o obj-$(CONFIG_SYS_FSL_DDRC_GEN4) += fsl_ddr_gen4.o +obj-$(CONFIG_SYS_FSL_MMDC) += fsl_mmdc.o diff --git a/drivers/ddr/fsl/fsl_mmdc.c b/drivers/ddr/fsl/fsl_mmdc.c new file mode 100644 index 0000000000..1e359674da --- /dev/null +++ b/drivers/ddr/fsl/fsl_mmdc.c @@ -0,0 +1,156 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Generic driver for Freescale MMDC(Multi Mode DDR Controller). + */ + +#include <common.h> +#include <fsl_mmdc.h> +#include <asm/io.h> + +static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits) +{ + int timeout = 1000; + + out_be32(ptr, value); + + while (in_be32(ptr) & bits) { + udelay(100); + timeout--; + } + if (timeout <= 0) + printf("Error: %p wait for clear timeout.\n", ptr); +} + +void mmdc_init(void) +{ + struct mmdc_regs *mmdc = (struct mmdc_regs *)CONFIG_SYS_FSL_DDR_ADDR; + unsigned int tmp; + + /* 1. set configuration request */ + out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ); + + /* 2. configure the desired timing parameters */ + out_be32(&mmdc->mdotc, CONFIG_MMDC_MDOTC); + out_be32(&mmdc->mdcfg0, CONFIG_MMDC_MDCFG0); + out_be32(&mmdc->mdcfg1, CONFIG_MMDC_MDCFG1); + out_be32(&mmdc->mdcfg2, CONFIG_MMDC_MDCFG2); + + /* 3. configure DDR type and other miscellaneous parameters */ + out_be32(&mmdc->mdmisc, CONFIG_MMDC_MDMISC); + out_be32(&mmdc->mpmur0, MMDC_MPMUR0_FRC_MSR); + out_be32(&mmdc->mdrwd, CONFIG_MMDC_MDRWD); + out_be32(&mmdc->mpodtctrl, CONFIG_MMDC_MPODTCTRL); + + /* 4. configure the required delay while leaving reset */ + out_be32(&mmdc->mdor, CONFIG_MMDC_MDOR); + + /* 5. configure DDR physical parameters */ + /* set row/column address width, burst length, data bus width */ + tmp = CONFIG_MMDC_MDCTL & ~(MDCTL_SDE0 | MDCTL_SDE1); + out_be32(&mmdc->mdctl, tmp); + /* configure address space partition */ + out_be32(&mmdc->mdasp, CONFIG_MMDC_MDASP); + + /* 6. perform a ZQ calibration - not needed here, doing in #8b */ + + /* 7. enable MMDC with the desired chip select */ +#if (CONFIG_CHIP_SELECTS_PER_CTRL == 1) + out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0); +#elif (CONFIG_CHIP_SELECTS_PER_CTRL == 2) + out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0 | MDCTL_SDE1); +#endif + + /* 8a. dram init sequence: update MRs for ZQ, ODT, PRE, etc */ + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(8) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2); + + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(0) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3); + + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1); + + out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(0x19) | + CMD_ADDR_LSB_MR_ADDR(0x30) | + MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0); + + /* 8b. ZQ calibration */ + out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(0x4) | MDSCR_ENABLE_CON_REQ | + CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0); + + set_wait_for_bits_clear(&mmdc->mpzqhwctrl, CONFIG_MMDC_MPZQHWCTRL, + MPZQHWCTRL_ZQ_HW_FORCE); + + /* 9a. calibrations now, wr lvl */ + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(0x84) | + MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1); + + out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | MDSCR_WL_EN | + CMD_NORMAL); + + set_wait_for_bits_clear(&mmdc->mpwlgcr, MPWLGCR_HW_WL_EN, + MPWLGCR_HW_WL_EN); + + mdelay(1); + + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1); + out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ); + + mdelay(1); + + /* 9b. read DQS gating calibration */ + out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ | + CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0); + + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3); + + out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN); + + /* set absolute read delay offset */ +#if defined(CONFIG_MMDC_MPRDDLCTL) + out_be32(&mmdc->mprddlctl, CONFIG_MMDC_MPRDDLCTL); +#else + out_be32(&mmdc->mprddlctl, MMDC_MPRDDLCTL_DEFAULT_DELAY); +#endif + set_wait_for_bits_clear(&mmdc->mpdgctrl0, + AUTO_RD_DQS_GATING_CALIBRATION_EN, + AUTO_RD_DQS_GATING_CALIBRATION_EN); + + out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG | + CMD_BANK_ADDR_3); + + /* 9c. read calibration */ + out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ | + CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0); + out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ | + CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3); + out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN); + set_wait_for_bits_clear(&mmdc->mprddlhwctl, + MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN, + MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN); + + out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG | + CMD_BANK_ADDR_3); + + /* 10. configure power-down, self-refresh entry, exit parameters */ + out_be32(&mmdc->mdpdc, CONFIG_MMDC_MDPDC); + out_be32(&mmdc->mapsr, MMDC_MAPSR_PWR_SAV_CTRL_STAT); + + /* 11. ZQ config again? do nothing here */ + + /* 12. refresh scheme */ + set_wait_for_bits_clear(&mmdc->mdref, CONFIG_MMDC_MDREF, + MDREF_START_REFRESH); + + /* 13. disable CON_REQ */ + out_be32(&mmdc->mdscr, MDSCR_DISABLE_CFG_REQ); +} |