diff options
Diffstat (limited to 'drivers/ddr/marvell/axp/ddr3_write_leveling.c')
| -rw-r--r-- | drivers/ddr/marvell/axp/ddr3_write_leveling.c | 1366 |
1 files changed, 1366 insertions, 0 deletions
diff --git a/drivers/ddr/marvell/axp/ddr3_write_leveling.c b/drivers/ddr/marvell/axp/ddr3_write_leveling.c new file mode 100644 index 0000000000..df3a3df4a6 --- /dev/null +++ b/drivers/ddr/marvell/axp/ddr3_write_leveling.c @@ -0,0 +1,1366 @@ +/* + * Copyright (C) Marvell International Ltd. and its affiliates + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#include <common.h> +#include <i2c.h> +#include <spl.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> + +#include "ddr3_hw_training.h" + +/* + * Debug + */ +#define DEBUG_WL_C(s, d, l) \ + DEBUG_WL_S(s); DEBUG_WL_D(d, l); DEBUG_WL_S("\n") +#define DEBUG_WL_FULL_C(s, d, l) \ + DEBUG_WL_FULL_S(s); DEBUG_WL_FULL_D(d, l); DEBUG_WL_FULL_S("\n") + +#ifdef MV_DEBUG_WL +#define DEBUG_RL_S(s) \ + debug_cond(ddr3_get_log_level() >= MV_LOG_LEVEL_2, "%s", s) +#define DEBUG_RL_D(d, l) \ + debug_cond(ddr3_get_log_level() >= MV_LOG_LEVEL_2, "%x", d) +#else +#define DEBUG_WL_S(s) +#define DEBUG_WL_D(d, l) +#endif + +#ifdef MV_DEBUG_WL_FULL +#define DEBUG_WL_FULL_S(s) puts(s) +#define DEBUG_WL_FULL_D(d, l) printf("%x", d) +#else +#define DEBUG_WL_FULL_S(s) +#define DEBUG_WL_FULL_D(d, l) +#endif + +#define WL_SUP_EXPECTED_DATA 0x21 +#define WL_SUP_READ_DRAM_ENTRY 0x8 + +static int ddr3_write_leveling_single_cs(u32 cs, u32 freq, int ratio_2to1, + u32 *result, + MV_DRAM_INFO *dram_info); +static void ddr3_write_ctrl_pup_reg(int bc_acc, u32 pup, u32 reg_addr, + u32 data); + +extern u16 odt_static[ODT_OPT][MAX_CS]; +extern u16 odt_dynamic[ODT_OPT][MAX_CS]; +extern u32 wl_sup_pattern[LEN_WL_SUP_PATTERN]; + +/* + * Name: ddr3_write_leveling_hw + * Desc: Execute Write leveling phase by HW + * Args: freq - current sequence frequency + * dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +int ddr3_write_leveling_hw(u32 freq, MV_DRAM_INFO *dram_info) +{ + u32 reg, phase, delay, cs, pup; +#ifdef MV88F67XX + int dpde_flag = 0; +#endif + /* Debug message - Start Read leveling procedure */ + DEBUG_WL_S("DDR3 - Write Leveling - Starting HW WL procedure\n"); + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); + if (reg & (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)) { + dpde_flag = 1; + reg_write(REG_DUNIT_CTRL_LOW_ADDR, + reg & ~(1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)); + } +#endif + + reg = 1 << REG_DRAM_TRAINING_WL_OFFS; + /* Config the retest number */ + reg |= (COUNT_HW_WL << REG_DRAM_TRAINING_RETEST_OFFS); + reg |= (dram_info->cs_ena << (REG_DRAM_TRAINING_CS_OFFS)); + reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ + + reg = reg_read(REG_DRAM_TRAINING_SHADOW_ADDR) | + (1 << REG_DRAM_TRAINING_AUTO_OFFS); + reg_write(REG_DRAM_TRAINING_SHADOW_ADDR, reg); + + /* Wait */ + do { + reg = reg_read(REG_DRAM_TRAINING_SHADOW_ADDR) & + (1 << REG_DRAM_TRAINING_AUTO_OFFS); + } while (reg); /* Wait for '0' */ + + reg = reg_read(REG_DRAM_TRAINING_ADDR); + /* Check if Successful */ + if (reg & (1 << REG_DRAM_TRAINING_ERROR_OFFS)) { + /* + * Read results to arrays - Results are required for WL + * High freq Supplement and DQS Centralization + */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + for (pup = 0; + pup < dram_info->num_of_total_pups; + pup++) { + if (pup == dram_info->num_of_std_pups + && dram_info->ecc_ena) + pup = ECC_PUP; + reg = + ddr3_read_pup_reg(PUP_WL_MODE, cs, + pup); + phase = + (reg >> REG_PHY_PHASE_OFFS) & + PUP_PHASE_MASK; + delay = reg & PUP_DELAY_MASK; + dram_info->wl_val[cs][pup][P] = phase; + dram_info->wl_val[cs][pup][D] = delay; + dram_info->wl_val[cs][pup][S] = + WL_HI_FREQ_STATE - 1; + reg = + ddr3_read_pup_reg(PUP_WL_MODE + 0x1, + cs, pup); + dram_info->wl_val[cs][pup][DQS] = + (reg & 0x3F); + } + +#ifdef MV_DEBUG_WL + /* Debug message - Print res for cs[i]: cs,PUP,Phase,Delay */ + DEBUG_WL_S("DDR3 - Write Leveling - Write Leveling Cs - "); + DEBUG_WL_D((u32) cs, 1); + DEBUG_WL_S(" Results:\n"); + for (pup = 0; + pup < dram_info->num_of_total_pups; + pup++) { + if (pup == dram_info->num_of_std_pups + && dram_info->ecc_ena) + pup = ECC_PUP; + DEBUG_WL_S("DDR3 - Write Leveling - PUP: "); + DEBUG_WL_D((u32) pup, 1); + DEBUG_WL_S(", Phase: "); + DEBUG_WL_D((u32) + dram_info->wl_val[cs][pup] + [P], 1); + DEBUG_WL_S(", Delay: "); + DEBUG_WL_D((u32) + dram_info->wl_val[cs][pup] + [D], 2); + DEBUG_WL_S("\n"); + } +#endif + } + } + + /* Dynamic pad issue (BTS669) during WL */ +#ifdef MV88F67XX + if (dpde_flag) { + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR) | + (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS); + reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); + } +#endif + + DEBUG_WL_S("DDR3 - Write Leveling - HW WL Ended Successfully\n"); + + return MV_OK; + } else { + DEBUG_WL_S("DDR3 - Write Leveling - HW WL Error\n"); + return MV_FAIL; + } +} + +/* + * Name: ddr3_wl_supplement + * Desc: Write Leveling Supplement + * Args: dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +int ddr3_wl_supplement(MV_DRAM_INFO *dram_info) +{ + u32 cs, cnt, pup_num, sum, phase, delay, max_pup_num, pup, sdram_offset; + u32 tmp_count, ecc, reg; + u32 ddr_width, tmp_pup, idx; + u32 sdram_pup_val, uj; + u32 one_clk_err = 0, align_err = 0, no_err = 0, err = 0, err_n = 0; + u32 sdram_data[LEN_WL_SUP_PATTERN] __aligned(32) = { 0 }; + + ddr_width = dram_info->ddr_width; + no_err = 0; + + DEBUG_WL_S("DDR3 - Write Leveling Hi-Freq Supplement - Starting\n"); + + switch (ddr_width) { + /* Data error from pos-adge to pos-adge */ + case 16: + one_clk_err = 4; + align_err = 4; + break; + case 32: + one_clk_err = 8; + align_err = 8; + break; + case 64: + one_clk_err = 0x10; + align_err = 0x10; + break; + default: + DEBUG_WL_S("Error - bus width!!!\n"); + return MV_FAIL; + } + + /* Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR) | + (1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + + /* [0] = 1 - Enable SW override */ + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + DEBUG_WL_S("DDR3 - Write Leveling Hi-Freq Supplement - SW Override Enabled\n"); + reg = (1 << REG_DRAM_TRAINING_AUTO_OFFS); + reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ + tmp_count = 0; + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + sum = 0; + /* + * 2 iterations loop: 1)actual WL results 2) fix WL + * if needed + */ + for (cnt = 0; cnt < COUNT_WL_HI_FREQ; cnt++) { + DEBUG_WL_C("COUNT = ", cnt, 1); + for (ecc = 0; ecc < (dram_info->ecc_ena + 1); + ecc++) { + if (ecc) { + DEBUG_WL_S("ECC PUP:\n"); + } else { + DEBUG_WL_S("DATA PUP:\n"); + } + + max_pup_num = + dram_info->num_of_std_pups * (1 - + ecc) + + ecc; + /* ECC Support - Switch ECC Mux on ecc=1 */ + reg = + (reg_read(REG_DRAM_TRAINING_2_ADDR) + & ~(1 << + REG_DRAM_TRAINING_2_ECC_MUX_OFFS)); + reg |= + (dram_info->ecc_ena * + ecc << + REG_DRAM_TRAINING_2_ECC_MUX_OFFS); + reg_write(REG_DRAM_TRAINING_2_ADDR, + reg); + ddr3_reset_phy_read_fifo(); + + /* Write to memory */ + sdram_offset = + tmp_count * (SDRAM_CS_SIZE + 1) + + 0x200; + if (MV_OK != ddr3_dram_sram_burst((u32) + wl_sup_pattern, + sdram_offset, + LEN_WL_SUP_PATTERN)) + return MV_FAIL; + + /* Read from memory */ + if (MV_OK != + ddr3_dram_sram_burst(sdram_offset, + (u32) + sdram_data, + LEN_WL_SUP_PATTERN)) + return MV_FAIL; + + /* Print the buffer */ + for (uj = 0; uj < LEN_WL_SUP_PATTERN; + uj++) { + if ((uj % 4 == 0) && (uj != 0)) { + DEBUG_WL_S("\n"); + } + DEBUG_WL_D(sdram_data[uj], + 8); + DEBUG_WL_S(" "); + } + + /* Check pup which DQS/DATA is error */ + for (pup = 0; pup < max_pup_num; pup++) { + /* ECC support - bit 8 */ + pup_num = (ecc) ? ECC_PUP : pup; + if (pup < 4) { /* lower 32 bit */ + tmp_pup = pup; + idx = + WL_SUP_READ_DRAM_ENTRY; + } else { /* higher 32 bit */ + tmp_pup = pup - 4; + idx = + WL_SUP_READ_DRAM_ENTRY + + 1; + } + DEBUG_WL_S("\nCS: "); + DEBUG_WL_D((u32) cs, 1); + DEBUG_WL_S(" PUP: "); + DEBUG_WL_D((u32) pup_num, 1); + DEBUG_WL_S("\n"); + sdram_pup_val = + ((sdram_data[idx] >> + ((tmp_pup) * 8)) & 0xFF); + DEBUG_WL_C("Actual Data = ", + sdram_pup_val, 2); + DEBUG_WL_C("Expected Data = ", + (WL_SUP_EXPECTED_DATA + + pup), 2); + /* + * ALINGHMENT: calculate + * expected data vs actual data + */ + err = + (WL_SUP_EXPECTED_DATA + + pup) - sdram_pup_val; + /* + * CLOCK LONG: calculate + * expected data vs actual data + */ + err_n = + sdram_pup_val - + (WL_SUP_EXPECTED_DATA + + pup); + DEBUG_WL_C("err = ", err, 2); + DEBUG_WL_C("err_n = ", err_n, + 2); + if (err == no_err) { + /* PUP is correct - increment State */ + dram_info->wl_val[cs] + [pup_num] + [S] = 1; + } else if (err_n == one_clk_err) { + /* clock is longer than DQS */ + phase = + ((dram_info->wl_val + [cs] + [pup_num][P] + + WL_HI_FREQ_SHIFT) + % MAX_PHASE_2TO1); + dram_info->wl_val[cs] + [pup_num] + [P] = phase; + delay = + dram_info->wl_val + [cs][pup_num] + [D]; + DEBUG_WL_S("#### Clock is longer than DQS more than one clk cycle ####\n"); + ddr3_write_pup_reg + (PUP_WL_MODE, cs, + pup * (1 - ecc) + + ECC_PUP * ecc, + phase, delay); + } else if (err == align_err) { + /* clock is align to DQS */ + phase = + dram_info->wl_val + [cs][pup_num] + [P]; + delay = + dram_info->wl_val + [cs][pup_num] + [D]; + DEBUG_WL_S("#### Alignment PUPS problem ####\n"); + if ((phase == 0) + || ((phase == 1) + && (delay <= + 0x10))) { + DEBUG_WL_S("#### Warning - Possible Layout Violation (DQS is longer than CLK)####\n"); + } + + phase = 0x0; + delay = 0x0; + dram_info->wl_val[cs] + [pup_num] + [P] = phase; + dram_info->wl_val[cs] + [pup_num] + [D] = delay; + ddr3_write_pup_reg + (PUP_WL_MODE, cs, + pup * (1 - ecc) + + ECC_PUP * ecc, + phase, delay); + } + /* Stop condition for ECC phase */ + pup = (ecc) ? max_pup_num : pup; + } + + /* ECC Support - Disable ECC MUX */ + reg = + (reg_read(REG_DRAM_TRAINING_2_ADDR) + & ~(1 << + REG_DRAM_TRAINING_2_ECC_MUX_OFFS)); + reg_write(REG_DRAM_TRAINING_2_ADDR, + reg); + } + } + + for (pup = 0; pup < dram_info->num_of_std_pups; pup++) + sum += dram_info->wl_val[cs][pup][S]; + + if (dram_info->ecc_ena) + sum += dram_info->wl_val[cs][ECC_PUP][S]; + + /* Checks if any pup is not locked after the change */ + if (sum < (WL_HI_FREQ_STATE * (dram_info->num_of_total_pups))) { + DEBUG_WL_C("DDR3 - Write Leveling Hi-Freq Supplement - didn't work for Cs - ", + (u32) cs, 1); + return MV_FAIL; + } + tmp_count++; + } + } + + dram_info->wl_max_phase = 0; + dram_info->wl_min_phase = 10; + + /* + * Read results to arrays - Results are required for DQS Centralization + */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + for (pup = 0; pup < dram_info->num_of_total_pups; pup++) { + if (pup == dram_info->num_of_std_pups + && dram_info->ecc_ena) + pup = ECC_PUP; + reg = ddr3_read_pup_reg(PUP_WL_MODE, cs, pup); + phase = + (reg >> REG_PHY_PHASE_OFFS) & + PUP_PHASE_MASK; + if (phase > dram_info->wl_max_phase) + dram_info->wl_max_phase = phase; + if (phase < dram_info->wl_min_phase) + dram_info->wl_min_phase = phase; + } + } + } + + /* Disable SW override - Must be in a different stage */ + /* [0]=0 - Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR); + reg &= ~(1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + reg = reg_read(REG_DRAM_TRAINING_1_ADDR) | + (1 << REG_DRAM_TRAINING_1_TRNBPOINT_OFFS); + reg_write(REG_DRAM_TRAINING_1_ADDR, reg); + + DEBUG_WL_S("DDR3 - Write Leveling Hi-Freq Supplement - Ended Successfully\n"); + + return MV_OK; +} + +/* + * Name: ddr3_write_leveling_hw_reg_dimm + * Desc: Execute Write leveling phase by HW + * Args: freq - current sequence frequency + * dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +int ddr3_write_leveling_hw_reg_dimm(u32 freq, MV_DRAM_INFO *dram_info) +{ + u32 reg, phase, delay, cs, pup, pup_num; + __maybe_unused int dpde_flag = 0; + + /* Debug message - Start Read leveling procedure */ + DEBUG_WL_S("DDR3 - Write Leveling - Starting HW WL procedure\n"); + + if (dram_info->num_cs > 2) { + DEBUG_WL_S("DDR3 - Write Leveling - HW WL Ended Successfully\n"); + return MV_NO_CHANGE; + } + + /* If target freq = 400 move clock start point */ + /* Write to control PUP to Control Deskew Regs */ + if (freq <= DDR_400) { + for (pup = 0; pup <= dram_info->num_of_total_pups; pup++) { + /* PUP_DELAY_MASK 0x1F */ + /* reg = 0x0C10001F + (uj << 16); */ + ddr3_write_ctrl_pup_reg(1, pup, CNTRL_PUP_DESKEW + pup, + 0x1F); + } + } + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); + if (reg & (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)) { + dpde_flag = 1; + reg_write(REG_DUNIT_CTRL_LOW_ADDR, + reg & ~(1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)); + } +#endif + + reg = (1 << REG_DRAM_TRAINING_WL_OFFS); + /* Config the retest number */ + reg |= (COUNT_HW_WL << REG_DRAM_TRAINING_RETEST_OFFS); + reg |= (dram_info->cs_ena << (REG_DRAM_TRAINING_CS_OFFS)); + reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ + + reg = reg_read(REG_DRAM_TRAINING_SHADOW_ADDR) | + (1 << REG_DRAM_TRAINING_AUTO_OFFS); + reg_write(REG_DRAM_TRAINING_SHADOW_ADDR, reg); + + /* Wait */ + do { + reg = reg_read(REG_DRAM_TRAINING_SHADOW_ADDR) & + (1 << REG_DRAM_TRAINING_AUTO_OFFS); + } while (reg); /* Wait for '0' */ + + reg = reg_read(REG_DRAM_TRAINING_ADDR); + /* Check if Successful */ + if (reg & (1 << REG_DRAM_TRAINING_ERROR_OFFS)) { + /* + * Read results to arrays - Results are required for WL High + * freq Supplement and DQS Centralization + */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + for (pup = 0; + pup < dram_info->num_of_total_pups; + pup++) { + if (pup == dram_info->num_of_std_pups + && dram_info->ecc_ena) + pup = ECC_BIT; + reg = + ddr3_read_pup_reg(PUP_WL_MODE, cs, + pup); + phase = + (reg >> REG_PHY_PHASE_OFFS) & + PUP_PHASE_MASK; + delay = reg & PUP_DELAY_MASK; + dram_info->wl_val[cs][pup][P] = phase; + dram_info->wl_val[cs][pup][D] = delay; + if ((phase == 1) && (delay >= 0x1D)) { + /* + * Need to do it here for + * uncorrect WL values + */ + ddr3_write_pup_reg(PUP_WL_MODE, + cs, pup, 0, + 0); + dram_info->wl_val[cs][pup][P] = + 0; + dram_info->wl_val[cs][pup][D] = + 0; + } + dram_info->wl_val[cs][pup][S] = + WL_HI_FREQ_STATE - 1; + reg = + ddr3_read_pup_reg(PUP_WL_MODE + 0x1, + cs, pup); + dram_info->wl_val[cs][pup][DQS] = + (reg & 0x3F); + } +#ifdef MV_DEBUG_WL + /* + * Debug message - Print res for cs[i]: + * cs,PUP,Phase,Delay + */ + DEBUG_WL_S("DDR3 - Write Leveling - Write Leveling Cs - "); + DEBUG_WL_D((u32) cs, 1); + DEBUG_WL_S(" Results:\n"); + for (pup = 0; + pup < dram_info->num_of_total_pups; + pup++) { + DEBUG_WL_S + ("DDR3 - Write Leveling - PUP: "); + DEBUG_WL_D((u32) pup, 1); + DEBUG_WL_S(", Phase: "); + DEBUG_WL_D((u32) + dram_info->wl_val[cs][pup] + [P], 1); + DEBUG_WL_S(", Delay: "); + DEBUG_WL_D((u32) + dram_info->wl_val[cs][pup] + [D], 2); + DEBUG_WL_S("\n"); + } +#endif + } + } + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + if (dpde_flag) { + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR) | + (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS); + reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); + } +#endif + DEBUG_WL_S("DDR3 - Write Leveling - HW WL Ended Successfully\n"); + + /* If target freq = 400 move clock back */ + /* Write to control PUP to Control Deskew Regs */ + if (freq <= DDR_400) { + for (pup = 0; pup <= dram_info->num_of_total_pups; + pup++) { + ddr3_write_ctrl_pup_reg(1, pup, + CNTRL_PUP_DESKEW + pup, 0); + } + } + + return MV_OK; + } else { + /* Configure Each PUP with locked leveling settings */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + for (pup = 0; + pup < dram_info->num_of_total_pups; + pup++) { + /* ECC support - bit 8 */ + pup_num = (pup == dram_info->num_of_std_pups) ? + ECC_BIT : pup; + ddr3_write_pup_reg(PUP_WL_MODE, cs, + pup_num, 0, 0); + } + } + } + + reg_write(REG_DRAM_TRAINING_ADDR, 0); + + /* If target freq = 400 move clock back */ + /* Write to control PUP to Control Deskew Regs */ + if (freq <= DDR_400) { + for (pup = 0; pup <= dram_info->num_of_total_pups; + pup++) { + ddr3_write_ctrl_pup_reg(1, pup, + CNTRL_PUP_DESKEW + pup, 0); + } + } + + DEBUG_WL_S("DDR3 - Write Leveling - HW WL Ended Successfully\n"); + return MV_NO_CHANGE; + } +} + +/* + * Name: ddr3_write_leveling_sw + * Desc: Execute Write leveling phase by SW + * Args: freq - current sequence frequency + * dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +int ddr3_write_leveling_sw(u32 freq, int ratio_2to1, MV_DRAM_INFO *dram_info) +{ + u32 reg, cs, cnt, pup, max_pup_num; + u32 res[MAX_CS]; + max_pup_num = dram_info->num_of_total_pups; + __maybe_unused int dpde_flag = 0; + + /* Debug message - Start Write leveling procedure */ + DEBUG_WL_S("DDR3 - Write Leveling - Starting SW WL procedure\n"); + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); + if (reg & (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)) { + dpde_flag = 1; + reg_write(REG_DUNIT_CTRL_LOW_ADDR, + reg & ~(1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)); + } +#endif + + /* Set Output buffer-off to all CS and correct ODT values */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_ODT_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + reg |= (1 << REG_DDR3_MR1_OUTBUF_DIS_OFFS); + + /* 0x15D0 - DDR3 MR0 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Qoff and RTT Values are set for all Cs\n"); + + /* Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR) | + (1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + /* [0] = 1 - Enable SW override */ + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + DEBUG_WL_FULL_S("DDR3 - Write Leveling - SW Override Enabled\n"); + + /* Enable PHY write leveling mode */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR) & + ~(1 << REG_DRAM_TRAINING_2_WL_MODE_OFFS); + /* [2] = 0 - TrnWLMode - Enable */ + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + /* Reset WL results arry */ + memset(dram_info->wl_val, 0, sizeof(u32) * MAX_CS * MAX_PUP_NUM * 7); + + /* Loop for each cs */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + DEBUG_WL_FULL_C("DDR3 - Write Leveling - Starting working with Cs - ", + (u32) cs, 1); + /* Refresh X9 current cs */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Refresh X9\n"); + for (cnt = 0; cnt < COUNT_WL_RFRS; cnt++) { + reg = + REG_SDRAM_OPERATION_CMD_RFRS & ~(1 << + (REG_SDRAM_OPERATION_CS_OFFS + + cs)); + /* [3-0] = 0x2 - refresh, [11-8] - enable current cs */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); /* 0x1418 - SDRAM Operation Register */ + + do { + reg = + ((reg_read + (REG_SDRAM_OPERATION_ADDR)) & + REG_SDRAM_OPERATION_CMD_RFRS_DONE); + } while (reg); /* Wait for '0' */ + } + + /* Configure MR1 in Cs[CsNum] - write leveling on, output buffer on */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Configure MR1 for current Cs: WL-on,OB-on\n"); + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_OUTBUF_WL_MASK; + /* Set ODT Values */ + reg &= REG_DDR3_MR1_ODT_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + /* Enable WL MODE */ + reg |= (1 << REG_DDR3_MR1_WL_ENA_OFFS); + /* [7]=1, [12]=0 - Output Buffer and write leveling enabled */ + reg_write(REG_DDR3_MR1_ADDR, reg); /* 0x15D4 - DDR3 MR1 Register */ + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + + /* Write leveling cs[cs] */ + if (MV_OK != + ddr3_write_leveling_single_cs(cs, freq, ratio_2to1, + (u32 *)(res + cs), + dram_info)) { + DEBUG_WL_FULL_C("DDR3 - Write Leveling single Cs - FAILED - Cs - ", + (u32) cs, 1); + for (pup = 0; pup < max_pup_num; pup++) { + if (((res[cs] >> pup) & 0x1) == 0) { + DEBUG_WL_C("Failed Byte : ", + pup, 1); + } + } + return MV_FAIL; + } + + /* Set TrnWLDeUpd - After each CS is done */ + reg = reg_read(REG_TRAINING_WL_ADDR) | + (1 << REG_TRAINING_WL_CS_DONE_OFFS); + /* 0x16AC - Training Write leveling register */ + reg_write(REG_TRAINING_WL_ADDR, reg); + + /* + * Debug message - Finished Write leveling cs[cs] - + * each PUP Fail/Success + */ + DEBUG_WL_FULL_C("DDR3 - Write Leveling - Finished Cs - ", (u32) cs, + 1); + DEBUG_WL_FULL_C("DDR3 - Write Leveling - The Results: 1-PUP locked, 0-PUP failed -", + (u32) res[cs], 3); + + /* + * Configure MR1 in cs[cs] - write leveling off (0), + * output buffer off (1) + */ + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_OUTBUF_WL_MASK; + reg |= (1 << REG_DDR3_MR1_OUTBUF_DIS_OFFS); + /* No need to sort ODT since it is same CS */ + /* 0x15D4 - DDR3 MR1 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + + /* Disable WL Mode */ + /* [2]=1 - TrnWLMode - Disable */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR); + reg |= (1 << REG_DRAM_TRAINING_2_WL_MODE_OFFS); + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + /* Disable SW override - Must be in a different stage */ + /* [0]=0 - Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR); + reg &= ~(1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + /* Set Output buffer-on to all CS and correct ODT values */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_ODT_MASK; + reg &= REG_DDR3_MR1_OUTBUF_WL_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + + /* 0x15D0 - DDR3 MR1 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + if (dpde_flag) { + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR) | + (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS); + reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); + } +#endif + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Finished WL procedure for all Cs\n"); + + return MV_OK; +} + +#if !defined(MV88F672X) +/* + * Name: ddr3_write_leveling_sw + * Desc: Execute Write leveling phase by SW + * Args: freq - current sequence frequency + * dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +int ddr3_write_leveling_sw_reg_dimm(u32 freq, int ratio_2to1, + MV_DRAM_INFO *dram_info) +{ + u32 reg, cs, cnt, pup; + u32 res[MAX_CS]; + __maybe_unused int dpde_flag = 0; + + /* Debug message - Start Write leveling procedure */ + DEBUG_WL_S("DDR3 - Write Leveling - Starting SW WL procedure\n"); + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); + if (reg & (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)) { + dpde_flag = 1; + reg_write(REG_DUNIT_CTRL_LOW_ADDR, + reg & ~(1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS)); + } +#endif + + /* If target freq = 400 move clock start point */ + /* Write to control PUP to Control Deskew Regs */ + if (freq <= DDR_400) { + for (pup = 0; pup <= dram_info->num_of_total_pups; pup++) { + /* PUP_DELAY_MASK 0x1F */ + /* reg = 0x0C10001F + (uj << 16); */ + ddr3_write_ctrl_pup_reg(1, pup, CNTRL_PUP_DESKEW + pup, + 0x1F); + } + } + + /* Set Output buffer-off to all CS and correct ODT values */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_ODT_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + reg |= (1 << REG_DDR3_MR1_OUTBUF_DIS_OFFS); + + /* 0x15D0 - DDR3 MR0 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Qoff and RTT Values are set for all Cs\n"); + + /* Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR) | + (1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + /* [0] = 1 - Enable SW override */ + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + DEBUG_WL_FULL_S("DDR3 - Write Leveling - SW Override Enabled\n"); + + /* Enable PHY write leveling mode */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR) & + ~(1 << REG_DRAM_TRAINING_2_WL_MODE_OFFS); + /* [2] = 0 - TrnWLMode - Enable */ + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + /* Loop for each cs */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + DEBUG_WL_FULL_C("DDR3 - Write Leveling - Starting working with Cs - ", + (u32) cs, 1); + + /* Refresh X9 current cs */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Refresh X9\n"); + for (cnt = 0; cnt < COUNT_WL_RFRS; cnt++) { + reg = + REG_SDRAM_OPERATION_CMD_RFRS & ~(1 << + (REG_SDRAM_OPERATION_CS_OFFS + + cs)); + /* [3-0] = 0x2 - refresh, [11-8] - enable current cs */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); /* 0x1418 - SDRAM Operation Register */ + + do { + reg = + ((reg_read + (REG_SDRAM_OPERATION_ADDR)) & + REG_SDRAM_OPERATION_CMD_RFRS_DONE); + } while (reg); /* Wait for '0' */ + } + + /* + * Configure MR1 in Cs[CsNum] - write leveling on, + * output buffer on + */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Configure MR1 for current Cs: WL-on,OB-on\n"); + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_OUTBUF_WL_MASK; + /* Set ODT Values */ + reg &= REG_DDR3_MR1_ODT_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + /* Enable WL MODE */ + reg |= (1 << REG_DDR3_MR1_WL_ENA_OFFS); + /* + * [7]=1, [12]=0 - Output Buffer and write leveling + * enabled + */ + /* 0x15D4 - DDR3 MR1 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + + /* Write leveling cs[cs] */ + if (MV_OK != + ddr3_write_leveling_single_cs(cs, freq, ratio_2to1, + (u32 *)(res + cs), + dram_info)) { + DEBUG_WL_FULL_C("DDR3 - Write Leveling single Cs - FAILED - Cs - ", + (u32) cs, 1); + return MV_FAIL; + } + + /* Set TrnWLDeUpd - After each CS is done */ + reg = reg_read(REG_TRAINING_WL_ADDR) | + (1 << REG_TRAINING_WL_CS_DONE_OFFS); + /* 0x16AC - Training Write leveling register */ + reg_write(REG_TRAINING_WL_ADDR, reg); + + /* + * Debug message - Finished Write leveling cs[cs] - + * each PUP Fail/Success + */ + DEBUG_WL_FULL_C("DDR3 - Write Leveling - Finished Cs - ", (u32) cs, + 1); + DEBUG_WL_FULL_C("DDR3 - Write Leveling - The Results: 1-PUP locked, 0-PUP failed -", + (u32) res[cs], 3); + + /* Configure MR1 in cs[cs] - write leveling off (0), output buffer off (1) */ + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_OUTBUF_WL_MASK; + reg |= (1 << REG_DDR3_MR1_OUTBUF_DIS_OFFS); + /* No need to sort ODT since it is same CS */ + /* 0x15D4 - DDR3 MR1 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + + /* Disable WL Mode */ + /* [2]=1 - TrnWLMode - Disable */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR); + reg |= (1 << REG_DRAM_TRAINING_2_WL_MODE_OFFS); + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + /* Disable SW override - Must be in a different stage */ + /* [0]=0 - Enable SW override */ + reg = reg_read(REG_DRAM_TRAINING_2_ADDR); + reg &= ~(1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); + /* 0x15B8 - Training SW 2 Register */ + reg_write(REG_DRAM_TRAINING_2_ADDR, reg); + + /* Set Output buffer-on to all CS and correct ODT values */ + for (cs = 0; cs < MAX_CS; cs++) { + if (dram_info->cs_ena & (1 << cs)) { + reg = reg_read(REG_DDR3_MR1_ADDR) & + REG_DDR3_MR1_ODT_MASK; + reg &= REG_DDR3_MR1_OUTBUF_WL_MASK; + reg |= odt_static[dram_info->cs_ena][cs]; + + /* 0x15D0 - DDR3 MR1 Register */ + reg_write(REG_DDR3_MR1_ADDR, reg); + /* Issue MRS Command to current cs */ + reg = REG_SDRAM_OPERATION_CMD_MR1 & + ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); + /* + * [3-0] = 0x4 - MR1 Command, [11-8] - + * enable current cs + */ + /* 0x1418 - SDRAM Operation Register */ + reg_write(REG_SDRAM_OPERATION_ADDR, reg); + + udelay(MRS_DELAY); + } + } + +#ifdef MV88F67XX + /* Dynamic pad issue (BTS669) during WL */ + if (dpde_flag) { + reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR) | + (1 << REG_DUNIT_CTRL_LOW_DPDE_OFFS); + reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); + } +#endif + + /* If target freq = 400 move clock back */ + /* Write to control PUP to Control Deskew Regs */ + if (freq <= DDR_400) { + for (pup = 0; pup <= dram_info->num_of_total_pups; pup++) { + ddr3_write_ctrl_pup_reg(1, pup, CNTRL_PUP_DESKEW + pup, + 0); + } + } + + DEBUG_WL_FULL_S("DDR3 - Write Leveling - Finished WL procedure for all Cs\n"); + return MV_OK; +} +#endif + +/* + * Name: ddr3_write_leveling_single_cs + * Desc: Execute Write leveling for single Chip select + * Args: cs - current chip select + * freq - current sequence frequency + * result - res array + * dram_info - main struct + * Notes: + * Returns: MV_OK if success, MV_FAIL if fail. + */ +static int ddr3_write_leveling_single_cs(u32 cs, u32 freq, int ratio_2to1, + u32 *result, MV_DRAM_INFO *dram_info) +{ + u32 reg, pup_num, delay, phase, phaseMax, max_pup_num, pup, + max_pup_mask; + + max_pup_num = dram_info->num_of_total_pups; + *result = 0; + u32 flag[MAX_PUP_NUM] = { 0 }; + + DEBUG_WL_FULL_C("DDR3 - Write Leveling Single Cs - WL for Cs - ", + (u32) cs, 1); + + switch (max_pup_num) { + case 2: + max_pup_mask = 0x3; + break; + case 4: + max_pup_mask = 0xf; + DEBUG_WL_C("max_pup_mask = ", max_pup_mask, 3); + break; + case 5: + max_pup_mask = 0x1f; + DEBUG_WL_C("max_pup_mask = ", max_pup_mask, 3); + break; + case 8: + max_pup_mask = 0xff; + DEBUG_WL_C("max_pup_mask = ", max_pup_mask, 3); + break; + case 9: + max_pup_mask = 0x1ff; + DEBUG_WL_C("max_pup_mask = ", max_pup_mask, 3); + break; + default: + DEBUG_WL_C("ddr3_write_leveling_single_cs wrong max_pup_num = ", + max_pup_num, 3); + return MV_FAIL; + } + + /* CS ODT Override */ + reg = reg_read(REG_SDRAM_ODT_CTRL_HIGH_ADDR) & + REG_SDRAM_ODT_CTRL_HIGH_OVRD_MASK; + reg |= (REG_SDRAM_ODT_CTRL_HIGH_OVRD_ENA << (2 * cs)); + /* Set 0x3 - Enable ODT on the curent cs and disable on other cs */ + /* 0x1498 - SDRAM ODT Control high */ + reg_write(REG_SDRAM_ODT_CTRL_HIGH_ADDR, reg); + + DEBUG_WL_FULL_S("DDR3 - Write Leveling Single Cs - ODT Asserted for current Cs\n"); + + /* tWLMRD Delay */ + /* Delay of minimum 40 Dram clock cycles - 20 Tclk cycles */ + udelay(1); + + /* [1:0] - current cs number */ + reg = (reg_read(REG_TRAINING_WL_ADDR) & REG_TRAINING_WL_CS_MASK) | cs; + reg |= (1 << REG_TRAINING_WL_UPD_OFFS); /* [2] - trnWLCsUpd */ + /* 0x16AC - Training Write leveling register */ + reg_write(REG_TRAINING_WL_ADDR, reg); + + /* Broadcast to all PUPs: Reset DQS phase, reset leveling delay */ + ddr3_write_pup_reg(PUP_WL_MODE, cs, PUP_BC, 0, 0); + + /* Seek Edge */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling Single Cs - Seek Edge - Current Cs\n"); + + /* Drive DQS high for one cycle - All data PUPs */ + DEBUG_WL_FULL_S("DDR3 - Write Leveling Single Cs - Seek Edge - Driving DQS high for one cycle\n"); + if (!ratio_2to1) { + reg = (reg_read(REG_TRAINING_WL_ADDR) & + REG_TRAINING_WL_RATIO_MASK) | REG_TRAINING_WL_1TO1; + } else { + reg = (reg_read(REG_TRAINING_WL_ADDR) & + REG_TRAINING_WL_RATIO_MASK) | REG_TRAINING_WL_2TO1; + } + /* 0x16AC - Training Write leveling register */ + reg_write(REG_TRAINING_WL_ADDR, reg); + + /* Wait tWLdelay */ + do { + /* [29] - trnWLDelayExp */ + reg = (reg_read(REG_TRAINING_WL_ADDR)) & + REG_TRAINING_WL_DELAYEXP_MASK; + } while (reg == 0x0); /* Wait for '1' */ + + /* Read WL res */ + reg = (reg_read(REG_TRAINING_WL_ADDR) >> REG_TRAINING_WL_RESULTS_OFFS) & + REG_TRAINING_WL_RESULTS_MASK; + /* [28:20] - TrnWLResult */ + + if (!ratio_2to1) /* Different phase options for 2:1 or 1:1 modes */ + phaseMax = MAX_PHASE_1TO1; + else + phaseMax = MAX_PHASE_2TO1; + + DEBUG_WL_FULL_S("DDR3 - Write Leveling Single Cs - Seek Edge - Shift DQS + Octet Leveling\n"); + + /* Shift DQS + Octet leveling */ + for (phase = 0; phase < phaseMax; phase++) { + for (delay = 0; delay < MAX_DELAY; delay++) { + /* Broadcast to all PUPs: DQS phase,leveling delay */ + ddr3_write_pup_reg(PUP_WL_MODE, cs, PUP_BC, phase, + delay); + + udelay(1); /* Delay of 3 Tclk cycles */ + + DEBUG_WL_FULL_S("DDR3 - Write Leveling Single Cs - Seek Edge: Phase = "); + DEBUG_WL_FULL_D((u32) phase, 1); + DEBUG_WL_FULL_S(", Delay = "); + DEBUG_WL_FULL_D((u32) delay, 1); + DEBUG_WL_FULL_S(", Counter = "); + DEBUG_WL_FULL_D((u32) i, 1); + DEBUG_WL_FULL_S("\n"); + + /* Drive DQS high for one cycle - All data PUPs */ + if (!ratio_2to1) { + reg = (reg_read(REG_TRAINING_WL_ADDR) & + REG_TRAINING_WL_RATIO_MASK) | + REG_TRAINING_WL_1TO1; + } else { + reg = (reg_read(REG_TRAINING_WL_ADDR) & + REG_TRAINING_WL_RATIO_MASK) | + REG_TRAINING_WL_2TO1; + } + reg_write(REG_TRAINING_WL_ADDR, reg); /* 0x16AC */ + + /* Wait tWLdelay */ + do { + reg = (reg_read(REG_TRAINING_WL_ADDR)) & + REG_TRAINING_WL_DELAYEXP_MASK; + } while (reg == 0x0); /* [29] Wait for '1' */ + + /* Read WL res */ + reg = reg_read(REG_TRAINING_WL_ADDR); + reg = (reg >> REG_TRAINING_WL_RESULTS_OFFS) & + REG_TRAINING_WL_RESULTS_MASK; /* [28:20] */ + + DEBUG_WL_FULL_C("DDR3 - Write Leveling Single Cs - Seek Edge: Results = ", + (u32) reg, 3); + + /* Update State machine */ + for (pup = 0; pup < (max_pup_num); pup++) { + /* ECC support - bit 8 */ + pup_num = (pup == dram_info->num_of_std_pups) ? + ECC_BIT : pup; + if (dram_info->wl_val[cs][pup][S] == 0) { + /* Update phase to PUP */ + dram_info->wl_val[cs][pup][P] = phase; + /* Update delay to PUP */ + dram_info->wl_val[cs][pup][D] = delay; + } + + if (((reg >> pup_num) & 0x1) == 0) + flag[pup_num] = 1; + + if (((reg >> pup_num) & 0x1) + && (flag[pup_num] == 1) + && (dram_info->wl_val[cs][pup][S] == 0)) { + /* + * If the PUP is locked now and in last + * counter states + */ + /* Go to next state */ + dram_info->wl_val[cs][pup][S] = 1; + /* Set res */ + *result = *result | (1 << pup_num); + } + } + + /* If all locked - Break the loops - Finished */ + if (*result == max_pup_mask) { + phase = phaseMax; + delay = MAX_DELAY; + DEBUG_WL_S("DDR3 - Write Leveling Single Cs - Seek Edge: All Locked\n"); + } + } + } + + /* Debug message - Print res for cs[i]: cs,PUP,Phase,Delay */ + DEBUG_WL_C("DDR3 - Write Leveling - Results for CS - ", (u32) cs, 1); + for (pup = 0; pup < (max_pup_num); pup++) { + DEBUG_WL_S("DDR3 - Write Leveling - PUP: "); + DEBUG_WL_D((u32) pup, 1); + DEBUG_WL_S(", Phase: "); + DEBUG_WL_D((u32) dram_info->wl_val[cs][pup][P], 1); + DEBUG_WL_S(", Delay: "); + DEBUG_WL_D((u32) dram_info->wl_val[cs][pup][D], 2); + DEBUG_WL_S("\n"); + } + + /* Check if some not locked and return error */ + if (*result != max_pup_mask) { + DEBUG_WL_S("DDR3 - Write Leveling - ERROR - not all PUPS were locked\n"); + return MV_FAIL; + } + + /* Configure Each PUP with locked leveling settings */ + for (pup = 0; pup < (max_pup_num); pup++) { + /* ECC support - bit 8 */ + pup_num = (pup == dram_info->num_of_std_pups) ? ECC_BIT : pup; + phase = dram_info->wl_val[cs][pup][P]; + delay = dram_info->wl_val[cs][pup][D]; + ddr3_write_pup_reg(PUP_WL_MODE, cs, pup_num, phase, delay); + } + + /* CS ODT Override */ + reg = reg_read(REG_SDRAM_ODT_CTRL_HIGH_ADDR) & + REG_SDRAM_ODT_CTRL_HIGH_OVRD_MASK; + /* 0x1498 - SDRAM ODT Control high */ + reg_write(REG_SDRAM_ODT_CTRL_HIGH_ADDR, reg); + + return MV_OK; +} + +/* + * Perform DDR3 Control PUP Indirect Write + */ +static void ddr3_write_ctrl_pup_reg(int bc_acc, u32 pup, u32 reg_addr, u32 data) +{ + u32 reg = 0; + + /* Store value for write */ + reg = (data & 0xFFFF); + + /* Set bit 26 for control PHY access */ + reg |= (1 << REG_PHY_CNTRL_OFFS); + + /* Configure BC or UC access to PHYs */ + if (bc_acc == 1) + reg |= (1 << REG_PHY_BC_OFFS); + else + reg |= (pup << REG_PHY_PUP_OFFS); + + /* Set PHY register address to write to */ + reg |= (reg_addr << REG_PHY_CS_OFFS); + + reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ + reg |= REG_PHY_REGISTRY_FILE_ACCESS_OP_WR; + reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ + + do { + reg = (reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR)) & + REG_PHY_REGISTRY_FILE_ACCESS_OP_DONE; + } while (reg); /* Wait for '0' to mark the end of the transaction */ +} |