diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/Kconfig | 20 | ||||
| -rw-r--r-- | drivers/serial/ns16550.c | 4 | ||||
| -rw-r--r-- | drivers/serial/serial-uclass.c | 68 |
3 files changed, 61 insertions, 31 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 5611fac0dc..4829284216 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -76,6 +76,26 @@ config DEBUG_UART_SHIFT value. Use this value to specify the shift to use, where 0=byte registers, 2=32-bit word registers, etc. +config SANDBOX_SERIAL + bool "Sandbox UART support" + depends on SANDBOX && DM + help + Select this to enable a seral UART for sandbox. This is required to + operate correctly, otherwise you will see no serial output from + sandbox. The emulated UART will display to the console and console + input will be fed into the UART. This allows you to interact with + U-Boot. + + The operation of the console is controlled by the -t command-line + flag. In raw mode, U-Boot sees all characters from the terminal + before they are processed, including Ctrl-C. In cooked mode, Ctrl-C + is processed by the terminal, and terminates U-Boot. Valid options + are: + + -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot + -t raw Raw mode, Ctrl-C is processed by U-Boot + -t cooked Cooked mode, Ctrl-C terminates + config UNIPHIER_SERIAL bool "Support for UniPhier on-chip UART" depends on ARCH_UNIPHIER && DM_SERIAL diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c index 3d376d7580..9b044a37da 100644 --- a/drivers/serial/ns16550.c +++ b/drivers/serial/ns16550.c @@ -65,6 +65,8 @@ static inline void serial_out_shift(void *addr, int shift, int value) out_le32(addr, value); #elif defined(CONFIG_SYS_NS16550_MEM32) && defined(CONFIG_SYS_BIG_ENDIAN) out_be32(addr, value); +#elif defined(CONFIG_SYS_NS16550_MEM32) + writel(value, addr); #elif defined(CONFIG_SYS_BIG_ENDIAN) writeb(value, addr + (1 << shift) - 1); #else @@ -80,6 +82,8 @@ static inline int serial_in_shift(void *addr, int shift) return in_le32(addr); #elif defined(CONFIG_SYS_NS16550_MEM32) && defined(CONFIG_SYS_BIG_ENDIAN) return in_be32(addr); +#elif defined(CONFIG_SYS_NS16550_MEM32) + return readl(addr); #elif defined(CONFIG_SYS_BIG_ENDIAN) return readb(addr + (1 << shift) - 1); #else diff --git a/drivers/serial/serial-uclass.c b/drivers/serial/serial-uclass.c index b8c2f48228..815fec3264 100644 --- a/drivers/serial/serial-uclass.c +++ b/drivers/serial/serial-uclass.c @@ -30,49 +30,55 @@ static const unsigned long baudrate_table[] = CONFIG_SYS_BAUDRATE_TABLE; static void serial_find_console_or_panic(void) { struct udevice *dev; - -#ifdef CONFIG_OF_CONTROL int node; - /* Check for a chosen console */ - node = fdtdec_get_chosen_node(gd->fdt_blob, "stdout-path"); - if (node < 0) - node = fdt_path_offset(gd->fdt_blob, "console"); - if (!uclass_get_device_by_of_offset(UCLASS_SERIAL, node, &dev)) { - gd->cur_serial_dev = dev; - return; - } - - /* - * If the console is not marked to be bound before relocation, bind - * it anyway. - */ - if (node > 0 && - !lists_bind_fdt(gd->dm_root, gd->fdt_blob, node, &dev)) { - if (!device_probe(dev)) { + if (OF_CONTROL && gd->fdt_blob) { + /* Check for a chosen console */ + node = fdtdec_get_chosen_node(gd->fdt_blob, "stdout-path"); + if (node < 0) + node = fdt_path_offset(gd->fdt_blob, "console"); + if (!uclass_get_device_by_of_offset(UCLASS_SERIAL, node, + &dev)) { gd->cur_serial_dev = dev; return; } + + /* + * If the console is not marked to be bound before relocation, + * bind it anyway. + */ + if (node > 0 && + !lists_bind_fdt(gd->dm_root, gd->fdt_blob, node, &dev)) { + if (!device_probe(dev)) { + gd->cur_serial_dev = dev; + return; + } + } } -#endif - /* - * Try to use CONFIG_CONS_INDEX if available (it is numbered from 1!). - * - * Failing that, get the device with sequence number 0, or in extremis - * just the first serial device we can find. But we insist on having - * a console (even if it is silent). - */ + if (!SPL_BUILD || !OF_CONTROL || !gd->fdt_blob) { + /* + * Try to use CONFIG_CONS_INDEX if available (it is numbered + * from 1!). + * + * Failing that, get the device with sequence number 0, or in + * extremis just the first serial device we can find. But we + * insist on having a console (even if it is silent). + */ #ifdef CONFIG_CONS_INDEX #define INDEX (CONFIG_CONS_INDEX - 1) #else #define INDEX 0 #endif - if (uclass_get_device_by_seq(UCLASS_SERIAL, INDEX, &dev) && - uclass_get_device(UCLASS_SERIAL, INDEX, &dev) && - (uclass_first_device(UCLASS_SERIAL, &dev) || !dev)) - panic_str("No serial driver found"); + if (!uclass_get_device_by_seq(UCLASS_SERIAL, INDEX, &dev) || + !uclass_get_device(UCLASS_SERIAL, INDEX, &dev) || + (!uclass_first_device(UCLASS_SERIAL, &dev) || dev)) { + gd->cur_serial_dev = dev; + return; + } #undef INDEX - gd->cur_serial_dev = dev; + } + + panic_str("No serial driver found"); } /* Called prior to relocation */ |