summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/fpga/spartan2.c46
-rw-r--r--drivers/fpga/spartan3.c46
-rw-r--r--drivers/fpga/virtex2.c40
-rw-r--r--drivers/fpga/xilinx.c179
-rw-r--r--drivers/fpga/zynqpl.c234
-rw-r--r--drivers/i2c/mvtwsi.c28
-rw-r--r--drivers/i2c/zynq_i2c.c4
-rw-r--r--drivers/mmc/fsl_esdhc.c2
-rw-r--r--drivers/net/designware.c2
-rw-r--r--drivers/net/dm9000x.c2
-rw-r--r--drivers/net/fm/Makefile1
-rw-r--r--drivers/net/fm/memac_phy.c8
-rw-r--r--drivers/net/ftmac110.c2
-rw-r--r--drivers/net/phy/atheros.c4
-rw-r--r--drivers/net/phy/phy.c3
-rw-r--r--drivers/net/phy/vitesse.c46
-rw-r--r--drivers/pci/fsl_pci_init.c9
-rw-r--r--drivers/power/tps6586x.c4
-rw-r--r--drivers/qe/qe.c9
-rw-r--r--drivers/serial/ns16550.c6
-rw-r--r--drivers/serial/serial.c10
-rw-r--r--drivers/usb/host/ehci-fsl.c15
-rw-r--r--drivers/video/atmel_hlcdfb.c8
-rw-r--r--drivers/video/mxc_ipuv3_fb.c5
24 files changed, 344 insertions, 369 deletions
diff --git a/drivers/fpga/spartan2.c b/drivers/fpga/spartan2.c
index 6eab1b51e5..7054056140 100644
--- a/drivers/fpga/spartan2.c
+++ b/drivers/fpga/spartan2.c
@@ -31,29 +31,29 @@
#define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */
#endif
-static int Spartan2_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Spartan2_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
-/* static int Spartan2_sp_info(Xilinx_desc *desc ); */
+static int spartan2_sp_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int spartan2_sp_dump(xilinx_desc *desc, const void *buf, size_t bsize);
+/* static int spartan2_sp_info(xilinx_desc *desc ); */
-static int Spartan2_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Spartan2_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
-/* static int Spartan2_ss_info(Xilinx_desc *desc ); */
+static int spartan2_ss_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int spartan2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize);
+/* static int spartan2_ss_info(xilinx_desc *desc ); */
/* ------------------------------------------------------------------------- */
/* Spartan-II Generic Implementation */
-int Spartan2_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__);
- ret_val = Spartan2_ss_load (desc, buf, bsize);
+ ret_val = spartan2_ss_load(desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__);
- ret_val = Spartan2_sp_load (desc, buf, bsize);
+ ret_val = spartan2_sp_load(desc, buf, bsize);
break;
default:
@@ -64,19 +64,19 @@ int Spartan2_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Spartan2_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__);
- ret_val = Spartan2_ss_dump (desc, buf, bsize);
+ ret_val = spartan2_ss_dump(desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__);
- ret_val = Spartan2_sp_dump (desc, buf, bsize);
+ ret_val = spartan2_sp_dump(desc, buf, bsize);
break;
default:
@@ -87,7 +87,7 @@ int Spartan2_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Spartan2_info( Xilinx_desc *desc )
+static int spartan2_info(xilinx_desc *desc)
{
return FPGA_SUCCESS;
}
@@ -96,10 +96,10 @@ int Spartan2_info( Xilinx_desc *desc )
/* ------------------------------------------------------------------------- */
/* Spartan-II Slave Parallel Generic Implementation */
-static int Spartan2_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_sp_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns;
+ xilinx_spartan2_slave_parallel_fns *fn = desc->iface_fns;
PRINTF ("%s: start with interface functions @ 0x%p\n",
__FUNCTION__, fn);
@@ -248,10 +248,10 @@ static int Spartan2_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-static int Spartan2_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_sp_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns;
+ xilinx_spartan2_slave_parallel_fns *fn = desc->iface_fns;
if (fn) {
unsigned char *data = (unsigned char *) buf;
@@ -296,10 +296,10 @@ static int Spartan2_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
/* ------------------------------------------------------------------------- */
-static int Spartan2_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_ss_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan2_Slave_Serial_fns *fn = desc->iface_fns;
+ xilinx_spartan2_slave_serial_fns *fn = desc->iface_fns;
int i;
unsigned char val;
@@ -439,7 +439,7 @@ static int Spartan2_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-static int Spartan2_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
/* Readback is only available through the Slave Parallel and */
/* boundary-scan interfaces. */
@@ -447,3 +447,9 @@ static int Spartan2_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
__FUNCTION__);
return FPGA_FAIL;
}
+
+struct xilinx_fpga_op spartan2_op = {
+ .load = spartan2_load,
+ .dump = spartan2_dump,
+ .info = spartan2_info,
+};
diff --git a/drivers/fpga/spartan3.c b/drivers/fpga/spartan3.c
index 3edc5c2c66..5c9412c2f6 100644
--- a/drivers/fpga/spartan3.c
+++ b/drivers/fpga/spartan3.c
@@ -35,29 +35,29 @@
#define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */
#endif
-static int Spartan3_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Spartan3_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
-/* static int Spartan3_sp_info(Xilinx_desc *desc ); */
+static int spartan3_sp_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int spartan3_sp_dump(xilinx_desc *desc, const void *buf, size_t bsize);
+/* static int spartan3_sp_info(xilinx_desc *desc ); */
-static int Spartan3_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Spartan3_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
-/* static int Spartan3_ss_info(Xilinx_desc *desc); */
+static int spartan3_ss_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int spartan3_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize);
+/* static int spartan3_ss_info(xilinx_desc *desc); */
/* ------------------------------------------------------------------------- */
/* Spartan-II Generic Implementation */
-int Spartan3_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__);
- ret_val = Spartan3_ss_load (desc, buf, bsize);
+ ret_val = spartan3_ss_load(desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__);
- ret_val = Spartan3_sp_load (desc, buf, bsize);
+ ret_val = spartan3_sp_load(desc, buf, bsize);
break;
default:
@@ -68,19 +68,19 @@ int Spartan3_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Spartan3_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__);
- ret_val = Spartan3_ss_dump (desc, buf, bsize);
+ ret_val = spartan3_ss_dump(desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__);
- ret_val = Spartan3_sp_dump (desc, buf, bsize);
+ ret_val = spartan3_sp_dump(desc, buf, bsize);
break;
default:
@@ -91,7 +91,7 @@ int Spartan3_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Spartan3_info( Xilinx_desc *desc )
+static int spartan3_info(xilinx_desc *desc)
{
return FPGA_SUCCESS;
}
@@ -100,10 +100,10 @@ int Spartan3_info( Xilinx_desc *desc )
/* ------------------------------------------------------------------------- */
/* Spartan-II Slave Parallel Generic Implementation */
-static int Spartan3_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_sp_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan3_Slave_Parallel_fns *fn = desc->iface_fns;
+ xilinx_spartan3_slave_parallel_fns *fn = desc->iface_fns;
PRINTF ("%s: start with interface functions @ 0x%p\n",
__FUNCTION__, fn);
@@ -254,10 +254,10 @@ static int Spartan3_sp_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-static int Spartan3_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_sp_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan3_Slave_Parallel_fns *fn = desc->iface_fns;
+ xilinx_spartan3_slave_parallel_fns *fn = desc->iface_fns;
if (fn) {
unsigned char *data = (unsigned char *) buf;
@@ -302,10 +302,10 @@ static int Spartan3_sp_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
/* ------------------------------------------------------------------------- */
-static int Spartan3_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_ss_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan3_Slave_Serial_fns *fn = desc->iface_fns;
+ xilinx_spartan3_slave_serial_fns *fn = desc->iface_fns;
int i;
unsigned char val;
@@ -457,7 +457,7 @@ static int Spartan3_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-static int Spartan3_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int spartan3_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
/* Readback is only available through the Slave Parallel and */
/* boundary-scan interfaces. */
@@ -465,3 +465,9 @@ static int Spartan3_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
__FUNCTION__);
return FPGA_FAIL;
}
+
+struct xilinx_fpga_op spartan3_op = {
+ .load = spartan3_load,
+ .dump = spartan3_dump,
+ .info = spartan3_info,
+};
diff --git a/drivers/fpga/virtex2.c b/drivers/fpga/virtex2.c
index b5a895d41a..e092147edd 100644
--- a/drivers/fpga/virtex2.c
+++ b/drivers/fpga/virtex2.c
@@ -84,25 +84,25 @@
#define CONFIG_SYS_FPGA_WAIT_CONFIG CONFIG_SYS_HZ/5 /* 200 ms */
#endif
-static int Virtex2_ssm_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Virtex2_ssm_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
+static int virtex2_ssm_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int virtex2_ssm_dump(xilinx_desc *desc, const void *buf, size_t bsize);
-static int Virtex2_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize);
-static int Virtex2_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
+static int virtex2_ss_load(xilinx_desc *desc, const void *buf, size_t bsize);
+static int virtex2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize);
-int Virtex2_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__);
- ret_val = Virtex2_ss_load (desc, buf, bsize);
+ ret_val = virtex2_ss_load(desc, buf, bsize);
break;
case slave_selectmap:
PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__);
- ret_val = Virtex2_ssm_load (desc, buf, bsize);
+ ret_val = virtex2_ssm_load(desc, buf, bsize);
break;
default:
@@ -112,19 +112,19 @@ int Virtex2_load(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Virtex2_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__);
- ret_val = Virtex2_ss_dump (desc, buf, bsize);
+ ret_val = virtex2_ss_dump(desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__);
- ret_val = Virtex2_ssm_dump (desc, buf, bsize);
+ ret_val = virtex2_ssm_dump(desc, buf, bsize);
break;
default:
@@ -134,7 +134,7 @@ int Virtex2_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-int Virtex2_info (Xilinx_desc * desc)
+static int virtex2_info(xilinx_desc *desc)
{
return FPGA_SUCCESS;
}
@@ -153,10 +153,10 @@ int Virtex2_info (Xilinx_desc * desc)
* INIT_B and DONE lines. If both are high, configuration has
* succeeded. Congratulations!
*/
-static int Virtex2_ssm_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_ssm_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
- Xilinx_Virtex2_Slave_SelectMap_fns *fn = desc->iface_fns;
+ xilinx_virtex2_slave_selectmap_fns *fn = desc->iface_fns;
PRINTF ("%s:%d: Start with interface functions @ 0x%p\n",
__FUNCTION__, __LINE__, fn);
@@ -352,10 +352,10 @@ static int Virtex2_ssm_load(Xilinx_desc *desc, const void *buf, size_t bsize)
/*
* Read the FPGA configuration data
*/
-static int Virtex2_ssm_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_ssm_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
- Xilinx_Virtex2_Slave_SelectMap_fns *fn = desc->iface_fns;
+ xilinx_virtex2_slave_selectmap_fns *fn = desc->iface_fns;
if (fn) {
unsigned char *data = (unsigned char *) buf;
@@ -404,16 +404,22 @@ static int Virtex2_ssm_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
return ret_val;
}
-static int Virtex2_ss_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_ss_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
printf ("%s: Slave Serial Loading is unsupported\n", __FUNCTION__);
return FPGA_FAIL;
}
-static int Virtex2_ss_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int virtex2_ss_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
printf ("%s: Slave Serial Dumping is unsupported\n", __FUNCTION__);
return FPGA_FAIL;
}
/* vim: set ts=4 tw=78: */
+
+struct xilinx_fpga_op virtex2_op = {
+ .load = virtex2_load,
+ .dump = virtex2_dump,
+ .info = virtex2_info,
+};
diff --git a/drivers/fpga/xilinx.c b/drivers/fpga/xilinx.c
index 2e0db535d4..8837f5c122 100644
--- a/drivers/fpga/xilinx.c
+++ b/drivers/fpga/xilinx.c
@@ -19,19 +19,8 @@
#include <spartan3.h>
#include <zynqpl.h>
-#if 0
-#define FPGA_DEBUG
-#endif
-
-/* Define FPGA_DEBUG to get debug printf's */
-#ifdef FPGA_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
/* Local Static Functions */
-static int xilinx_validate (Xilinx_desc * desc, char *fn);
+static int xilinx_validate(xilinx_desc *desc, char *fn);
/* ------------------------------------------------------------------------- */
@@ -43,7 +32,7 @@ int fpga_loadbitstream(int devnum, char *fpgadata, size_t size)
unsigned char *dataptr;
unsigned int i;
const fpga_desc *desc;
- Xilinx_desc *xdesc;
+ xilinx_desc *xdesc;
dataptr = (unsigned char *)fpgadata;
/* Find out fpga_description */
@@ -94,7 +83,7 @@ int fpga_loadbitstream(int devnum, char *fpgadata, size_t size)
return FPGA_FAIL;
}
} else {
- printf("%s: Please fill correct device ID to Xilinx_desc\n",
+ printf("%s: Please fill correct device ID to xilinx_desc\n",
__func__);
}
printf(" part number = \"%s\"\n", buffer);
@@ -141,134 +130,40 @@ int fpga_loadbitstream(int devnum, char *fpgadata, size_t size)
return fpga_load(devnum, dataptr, swapsize);
}
-int xilinx_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+int xilinx_load(xilinx_desc *desc, const void *buf, size_t bsize)
{
- int ret_val = FPGA_FAIL; /* assume a failure */
-
if (!xilinx_validate (desc, (char *)__FUNCTION__)) {
printf ("%s: Invalid device descriptor\n", __FUNCTION__);
- } else
- switch (desc->family) {
- case Xilinx_Spartan2:
-#if defined(CONFIG_FPGA_SPARTAN2)
- PRINTF ("%s: Launching the Spartan-II Loader...\n",
- __FUNCTION__);
- ret_val = Spartan2_load (desc, buf, bsize);
-#else
- printf ("%s: No support for Spartan-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Spartan3:
-#if defined(CONFIG_FPGA_SPARTAN3)
- PRINTF ("%s: Launching the Spartan-III Loader...\n",
- __FUNCTION__);
- ret_val = Spartan3_load (desc, buf, bsize);
-#else
- printf ("%s: No support for Spartan-III devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Virtex2:
-#if defined(CONFIG_FPGA_VIRTEX2)
- PRINTF ("%s: Launching the Virtex-II Loader...\n",
- __FUNCTION__);
- ret_val = Virtex2_load (desc, buf, bsize);
-#else
- printf ("%s: No support for Virtex-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case xilinx_zynq:
-#if defined(CONFIG_FPGA_ZYNQPL)
- PRINTF("%s: Launching the Zynq PL Loader...\n",
- __func__);
- ret_val = zynq_load(desc, buf, bsize);
-#else
- printf("%s: No support for Zynq devices.\n",
- __func__);
-#endif
- break;
-
- default:
- printf ("%s: Unsupported family type, %d\n",
- __FUNCTION__, desc->family);
- }
+ return FPGA_FAIL;
+ }
- return ret_val;
+ return desc->operations->load(desc, buf, bsize);
}
-int xilinx_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+int xilinx_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
- int ret_val = FPGA_FAIL; /* assume a failure */
-
if (!xilinx_validate (desc, (char *)__FUNCTION__)) {
printf ("%s: Invalid device descriptor\n", __FUNCTION__);
- } else
- switch (desc->family) {
- case Xilinx_Spartan2:
-#if defined(CONFIG_FPGA_SPARTAN2)
- PRINTF ("%s: Launching the Spartan-II Reader...\n",
- __FUNCTION__);
- ret_val = Spartan2_dump (desc, buf, bsize);
-#else
- printf ("%s: No support for Spartan-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Spartan3:
-#if defined(CONFIG_FPGA_SPARTAN3)
- PRINTF ("%s: Launching the Spartan-III Reader...\n",
- __FUNCTION__);
- ret_val = Spartan3_dump (desc, buf, bsize);
-#else
- printf ("%s: No support for Spartan-III devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Virtex2:
-#if defined( CONFIG_FPGA_VIRTEX2)
- PRINTF ("%s: Launching the Virtex-II Reader...\n",
- __FUNCTION__);
- ret_val = Virtex2_dump (desc, buf, bsize);
-#else
- printf ("%s: No support for Virtex-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case xilinx_zynq:
-#if defined(CONFIG_FPGA_ZYNQPL)
- PRINTF("%s: Launching the Zynq PL Reader...\n",
- __func__);
- ret_val = zynq_dump(desc, buf, bsize);
-#else
- printf("%s: No support for Zynq devices.\n",
- __func__);
-#endif
- break;
-
- default:
- printf ("%s: Unsupported family type, %d\n",
- __FUNCTION__, desc->family);
- }
+ return FPGA_FAIL;
+ }
- return ret_val;
+ return desc->operations->dump(desc, buf, bsize);
}
-int xilinx_info (Xilinx_desc * desc)
+int xilinx_info(xilinx_desc *desc)
{
int ret_val = FPGA_FAIL;
if (xilinx_validate (desc, (char *)__FUNCTION__)) {
printf ("Family: \t");
switch (desc->family) {
- case Xilinx_Spartan2:
+ case xilinx_spartan2:
printf ("Spartan-II\n");
break;
- case Xilinx_Spartan3:
+ case xilinx_spartan3:
printf ("Spartan-III\n");
break;
- case Xilinx_Virtex2:
+ case xilinx_virtex2:
printf ("Virtex-II\n");
break;
case xilinx_zynq:
@@ -315,47 +210,7 @@ int xilinx_info (Xilinx_desc * desc)
if (desc->iface_fns) {
printf ("Device Function Table @ 0x%p\n", desc->iface_fns);
- switch (desc->family) {
- case Xilinx_Spartan2:
-#if defined(CONFIG_FPGA_SPARTAN2)
- Spartan2_info (desc);
-#else
- /* just in case */
- printf ("%s: No support for Spartan-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Spartan3:
-#if defined(CONFIG_FPGA_SPARTAN3)
- Spartan3_info (desc);
-#else
- /* just in case */
- printf ("%s: No support for Spartan-III devices.\n",
- __FUNCTION__);
-#endif
- break;
- case Xilinx_Virtex2:
-#if defined(CONFIG_FPGA_VIRTEX2)
- Virtex2_info (desc);
-#else
- /* just in case */
- printf ("%s: No support for Virtex-II devices.\n",
- __FUNCTION__);
-#endif
- break;
- case xilinx_zynq:
-#if defined(CONFIG_FPGA_ZYNQPL)
- zynq_info(desc);
-#else
- /* just in case */
- printf("%s: No support for Zynq devices.\n",
- __func__);
-#endif
- /* Add new family types here */
- default:
- /* we don't need a message here - we give one up above */
- ;
- }
+ desc->operations->info(desc);
} else
printf ("No Device Function Table.\n");
@@ -369,7 +224,7 @@ int xilinx_info (Xilinx_desc * desc)
/* ------------------------------------------------------------------------- */
-static int xilinx_validate (Xilinx_desc * desc, char *fn)
+static int xilinx_validate(xilinx_desc *desc, char *fn)
{
int ret_val = false;
diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
index 923a1586d8..c066f21d79 100644
--- a/drivers/fpga/zynqpl.c
+++ b/drivers/fpga/zynqpl.c
@@ -36,7 +36,7 @@
#define CONFIG_SYS_FPGA_PROG_TIME (CONFIG_SYS_HZ * 4) /* 4 s */
#endif
-int zynq_info(Xilinx_desc *desc)
+static int zynq_info(xilinx_desc *desc)
{
return FPGA_SUCCESS;
}
@@ -147,76 +147,57 @@ static void *check_data(u8 *buf, size_t bsize, u32 *swap)
}
/* Loop can be huge - support CTRL + C */
if (ctrlc())
- return 0;
+ return NULL;
}
- return 0;
+ return NULL;
}
-
-int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int zynq_dma_transfer(u32 srcbuf, u32 srclen, u32 dstbuf, u32 dstlen)
{
- unsigned long ts; /* Timestamp */
- u32 partialbit = 0;
- u32 i, control, isr_status, status, swap, diff;
- u32 *buf_start;
-
- /* Detect if we are going working with partial or full bitstream */
- if (bsize != desc->size) {
- printf("%s: Working with partial bitstream\n", __func__);
- partialbit = 1;
- }
+ unsigned long ts;
+ u32 isr_status;
- buf_start = check_data((u8 *)buf, bsize, &swap);
- if (!buf_start)
- return FPGA_FAIL;
-
- /* Check if data is postpone from start */
- diff = (u32)buf_start - (u32)buf;
- if (diff) {
- printf("%s: Bitstream is not validated yet (diff %x)\n",
- __func__, diff);
- return FPGA_FAIL;
- }
+ /* Set up the transfer */
+ writel((u32)srcbuf, &devcfg_base->dma_src_addr);
+ writel(dstbuf, &devcfg_base->dma_dst_addr);
+ writel(srclen, &devcfg_base->dma_src_len);
+ writel(dstlen, &devcfg_base->dma_dst_len);
- if ((u32)buf < SZ_1M) {
- printf("%s: Bitstream has to be placed up to 1MB (%x)\n",
- __func__, (u32)buf);
- return FPGA_FAIL;
- }
+ isr_status = readl(&devcfg_base->int_sts);
- if ((u32)buf != ALIGN((u32)buf, ARCH_DMA_MINALIGN)) {
- u32 *new_buf = (u32 *)ALIGN((u32)buf, ARCH_DMA_MINALIGN);
+ /* Polling the PCAP_INIT status for Set */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
+ if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
+ debug("%s: Error: isr = 0x%08X\n", __func__,
+ isr_status);
+ debug("%s: Write count = 0x%08X\n", __func__,
+ readl(&devcfg_base->write_count));
+ debug("%s: Read count = 0x%08X\n", __func__,
+ readl(&devcfg_base->read_count));
- /*
- * This might be dangerous but permits to flash if
- * ARCH_DMA_MINALIGN is greater than header size
- */
- if (new_buf > buf_start) {
- debug("%s: Aligned buffer is after buffer start\n",
- __func__);
- new_buf -= ARCH_DMA_MINALIGN;
+ return FPGA_FAIL;
}
+ if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
+ printf("%s: Timeout wait for DMA to complete\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
- printf("%s: Align buffer at %x to %x(swap %d)\n", __func__,
- (u32)buf_start, (u32)new_buf, swap);
-
- for (i = 0; i < (bsize/4); i++)
- new_buf[i] = load_word(&buf_start[i], swap);
-
- swap = SWAP_DONE;
- buf = new_buf;
- } else if (swap != SWAP_DONE) {
- /* For bitstream which are aligned */
- u32 *new_buf = (u32 *)buf;
+ debug("%s: DMA transfer is done\n", __func__);
- printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__,
- swap);
+ /* Clear out the DMA status */
+ writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
- for (i = 0; i < (bsize/4); i++)
- new_buf[i] = load_word(&buf_start[i], swap);
+ return FPGA_SUCCESS;
+}
- swap = SWAP_DONE;
- }
+static int zynq_dma_xfer_init(u32 partialbit)
+{
+ u32 status, control, isr_status;
+ unsigned long ts;
/* Clear loopback bit */
clrbits_le32(&devcfg_base->mctrl, DEVCFG_MCTRL_PCAP_LPBK);
@@ -298,6 +279,101 @@ int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status);
}
+ return FPGA_SUCCESS;
+}
+
+static u32 *zynq_align_dma_buffer(u32 *buf, u32 len, u32 swap)
+{
+ u32 *new_buf;
+ u32 i;
+
+ if ((u32)buf != ALIGN((u32)buf, ARCH_DMA_MINALIGN)) {
+ new_buf = (u32 *)ALIGN((u32)buf, ARCH_DMA_MINALIGN);
+
+ /*
+ * This might be dangerous but permits to flash if
+ * ARCH_DMA_MINALIGN is greater than header size
+ */
+ if (new_buf > buf) {
+ debug("%s: Aligned buffer is after buffer start\n",
+ __func__);
+ new_buf -= ARCH_DMA_MINALIGN;
+ }
+ printf("%s: Align buffer at %x to %x(swap %d)\n", __func__,
+ (u32)buf, (u32)new_buf, swap);
+
+ for (i = 0; i < (len/4); i++)
+ new_buf[i] = load_word(&buf[i], swap);
+
+ buf = new_buf;
+ } else if (swap != SWAP_DONE) {
+ /* For bitstream which are aligned */
+ u32 *new_buf = (u32 *)buf;
+
+ printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__,
+ swap);
+
+ for (i = 0; i < (len/4); i++)
+ new_buf[i] = load_word(&buf[i], swap);
+ }
+
+ return buf;
+}
+
+static int zynq_validate_bitstream(xilinx_desc *desc, const void *buf,
+ size_t bsize, u32 blocksize, u32 *swap,
+ u32 *partialbit)
+{
+ u32 *buf_start;
+ u32 diff;
+
+ /* Detect if we are going working with partial or full bitstream */
+ if (bsize != desc->size) {
+ printf("%s: Working with partial bitstream\n", __func__);
+ *partialbit = 1;
+ }
+ buf_start = check_data((u8 *)buf, blocksize, swap);
+
+ if (!buf_start)
+ return FPGA_FAIL;
+
+ /* Check if data is postpone from start */
+ diff = (u32)buf_start - (u32)buf;
+ if (diff) {
+ printf("%s: Bitstream is not validated yet (diff %x)\n",
+ __func__, diff);
+ return FPGA_FAIL;
+ }
+
+ if ((u32)buf < SZ_1M) {
+ printf("%s: Bitstream has to be placed up to 1MB (%x)\n",
+ __func__, (u32)buf);
+ return FPGA_FAIL;
+ }
+
+ if (zynq_dma_xfer_init(*partialbit))
+ return FPGA_FAIL;
+
+ return 0;
+}
+
+
+static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize)
+{
+ unsigned long ts; /* Timestamp */
+ u32 partialbit = 0;
+ u32 isr_status, swap;
+
+ /*
+ * send bsize inplace of blocksize as it was not a bitstream
+ * in chunks
+ */
+ if (zynq_validate_bitstream(desc, buf, bsize, bsize, &swap,
+ &partialbit))
+ return FPGA_FAIL;
+
+ buf = zynq_align_dma_buffer((u32 *)buf, bsize, swap);
+
debug("%s: Source = 0x%08X\n", __func__, (u32)buf);
debug("%s: Size = %zu\n", __func__, bsize);
@@ -305,37 +381,10 @@ int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
flush_dcache_range((u32)buf, (u32)buf +
roundup(bsize, ARCH_DMA_MINALIGN));
- /* Set up the transfer */
- writel((u32)buf | 1, &devcfg_base->dma_src_addr);
- writel(0xFFFFFFFF, &devcfg_base->dma_dst_addr);
- writel(bsize >> 2, &devcfg_base->dma_src_len);
- writel(0, &devcfg_base->dma_dst_len);
+ if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
+ return FPGA_FAIL;
isr_status = readl(&devcfg_base->int_sts);
-
- /* Polling the PCAP_INIT status for Set */
- ts = get_timer(0);
- while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
- if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
- debug("%s: Error: isr = 0x%08X\n", __func__,
- isr_status);
- debug("%s: Write count = 0x%08X\n", __func__,
- readl(&devcfg_base->write_count));
- debug("%s: Read count = 0x%08X\n", __func__,
- readl(&devcfg_base->read_count));
-
- return FPGA_FAIL;
- }
- if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
- printf("%s: Timeout wait for DMA to complete\n",
- __func__);
- return FPGA_FAIL;
- }
- isr_status = readl(&devcfg_base->int_sts);
- }
-
- debug("%s: DMA transfer is done\n", __func__);
-
/* Check FPGA configuration completion */
ts = get_timer(0);
while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
@@ -349,16 +398,19 @@ int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
debug("%s: FPGA config done\n", __func__);
- /* Clear out the DMA status */
- writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
-
if (!partialbit)
zynq_slcr_devcfg_enable();
return FPGA_SUCCESS;
}
-int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+static int zynq_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
return FPGA_FAIL;
}
+
+struct xilinx_fpga_op zynq_op = {
+ .load = zynq_load,
+ .dump = zynq_dump,
+ .info = zynq_info,
+};
diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
index 90c8387918..5ba0e03862 100644
--- a/drivers/i2c/mvtwsi.c
+++ b/drivers/i2c/mvtwsi.c
@@ -216,21 +216,7 @@ static int twsi_stop(int status)
*/
#define TWSI_FREQUENCY(m, n) \
- ((u8) (CONFIG_SYS_TCLK / (10 * (m + 1) * 2 * (1 << n))))
-
-/*
- * These are required to be reprogrammed before enabling the controller
- * because a reset loses them.
- * Default values come from the spec, but a twsi_reset will change them.
- * twsi_slave_address left uninitialized lest checkpatch.pl complains.
- */
-
-/* Baudrate generator: m (bits 7..4) =4, n (bits 3..0) =4 */
-static u8 twsi_baud_rate = 0x44; /* baudrate at controller reset */
-/* Default frequency corresponding to default m=4, n=4 */
-static u8 twsi_actual_speed = TWSI_FREQUENCY(4, 4);
-/* Default slave address is 0 (so is an uninitialized static) */
-static u8 twsi_slave_address;
+ (CONFIG_SYS_TCLK / (10 * (m + 1) * (1 << n)))
/*
* Reset controller.
@@ -238,7 +224,7 @@ static u8 twsi_slave_address;
* Controller reset also resets the baud rate and slave address, so
* re-establish them.
*/
-static void twsi_reset(void)
+static void twsi_reset(u8 baud_rate, u8 slave_address)
{
/* ensure controller will be enabled by any twsi*() function */
twsi_control_flags = MVTWSI_CONTROL_TWSIEN;
@@ -247,9 +233,9 @@ static void twsi_reset(void)
/* wait 2 ms -- this is what the Marvell LSP does */
udelay(20000);
/* set baud rate */
- writel(twsi_baud_rate, &twsi->baudrate);
+ writel(baud_rate, &twsi->baudrate);
/* set slave address even though we don't use it */
- writel(twsi_slave_address, &twsi->slave_address);
+ writel(slave_address, &twsi->slave_address);
writel(0, &twsi->xtnd_slave_addr);
/* assert STOP but don't care for the result */
(void) twsi_stop(0);
@@ -277,12 +263,8 @@ void i2c_init(int requested_speed, int slaveadd)
}
}
}
- /* save baud rate and slave for later calls to twsi_reset */
- twsi_baud_rate = baud;
- twsi_actual_speed = highest_speed;
- twsi_slave_address = slaveadd;
/* reset controller */
- twsi_reset();
+ twsi_reset(baud, slaveadd);
}
/*
diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c
index f1f65131a2..b3264af452 100644
--- a/drivers/i2c/zynq_i2c.c
+++ b/drivers/i2c/zynq_i2c.c
@@ -142,7 +142,7 @@ static u32 zynq_i2c_wait(struct zynq_i2c_registers *zynq_i2c, u32 mask)
break;
}
#ifdef DEBUG
- zynq_i2c_debug_status(zynq_i2c));
+ zynq_i2c_debug_status(zynq_i2c);
#endif
/* Clear interrupt status flags */
writel(int_status & mask, &zynq_i2c->interrupt_status);
@@ -235,7 +235,7 @@ static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr,
clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD);
#ifdef DEBUG
- zynq_i2c_debug_status();
+ zynq_i2c_debug_status(zynq_i2c);
#endif
return 0;
}
diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 4c3b93d413..50cba64d99 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -96,7 +96,7 @@ static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data)
else if (cmd->resp_type & MMC_RSP_PRESENT)
xfertyp |= XFERTYP_RSPTYP_48;
-#if defined(CONFIG_MX53) || defined(CONFIG_T4240QDS)
+#if defined(CONFIG_MX53) || defined(CONFIG_PPC_T4240)
if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
xfertyp |= XFERTYP_CMDTYP_ABORT;
#endif
diff --git a/drivers/net/designware.c b/drivers/net/designware.c
index c45593bcc0..78751b2600 100644
--- a/drivers/net/designware.c
+++ b/drivers/net/designware.c
@@ -390,6 +390,8 @@ static int dw_phy_init(struct eth_device *dev)
if (!phydev)
return -1;
+ phy_connect_dev(phydev, dev);
+
phydev->supported &= PHY_GBIT_FEATURES;
phydev->advertising = phydev->supported;
diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c
index b68d808c74..4de9d41642 100644
--- a/drivers/net/dm9000x.c
+++ b/drivers/net/dm9000x.c
@@ -345,7 +345,7 @@ static int dm9000_init(struct eth_device *dev, bd_t *bd)
if (!is_valid_ether_addr(dev->enetaddr)) {
#ifdef CONFIG_RANDOM_MACADDR
printf("Bad MAC address (uninitialized EEPROM?), randomizing\n");
- eth_random_enetaddr(dev->enetaddr);
+ eth_random_addr(dev->enetaddr);
printf("MAC: %pM\n", dev->enetaddr);
#else
printf("WARNING: Bad MAC address (uninitialized EEPROM?)\n");
diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile
index ee5d768937..5ae3b167a9 100644
--- a/drivers/net/fm/Makefile
+++ b/drivers/net/fm/Makefile
@@ -32,5 +32,6 @@ obj-$(CONFIG_PPC_T2080) += t2080.o
obj-$(CONFIG_PPC_T2081) += t2080.o
obj-$(CONFIG_PPC_T4240) += t4240.o
obj-$(CONFIG_PPC_T4160) += t4240.o
+obj-$(CONFIG_PPC_T4080) += t4240.o
obj-$(CONFIG_PPC_B4420) += b4860.o
obj-$(CONFIG_PPC_B4860) += b4860.o
diff --git a/drivers/net/fm/memac_phy.c b/drivers/net/fm/memac_phy.c
index 2f4bc11a6c..de9c0e9cd2 100644
--- a/drivers/net/fm/memac_phy.c
+++ b/drivers/net/fm/memac_phy.c
@@ -29,10 +29,8 @@ int memac_mdio_write(struct mii_dev *bus, int port_addr, int dev_addr,
c45 = 0; /* clause 22 */
dev_addr = regnum & 0x1f;
clrbits_be32(&regs->mdio_stat, MDIO_STAT_ENC);
- } else {
+ } else
setbits_be32(&regs->mdio_stat, MDIO_STAT_ENC);
- setbits_be32(&regs->mdio_stat, MDIO_STAT_HOLD_15_CLK);
- }
/* Wait till the bus is free */
while ((in_be32(&regs->mdio_stat)) & MDIO_STAT_BSY)
@@ -76,10 +74,8 @@ int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr,
c45 = 0; /* clause 22 */
dev_addr = regnum & 0x1f;
clrbits_be32(&regs->mdio_stat, MDIO_STAT_ENC);
- } else {
+ } else
setbits_be32(&regs->mdio_stat, MDIO_STAT_ENC);
- setbits_be32(&regs->mdio_stat, MDIO_STAT_HOLD_15_CLK);
- }
/* Wait till the bus is free */
while ((in_be32(&regs->mdio_stat)) & MDIO_STAT_BSY)
diff --git a/drivers/net/ftmac110.c b/drivers/net/ftmac110.c
index 8eee272cf1..98c4f09629 100644
--- a/drivers/net/ftmac110.c
+++ b/drivers/net/ftmac110.c
@@ -425,7 +425,7 @@ int ftmac110_initialize(bd_t *bis)
dev->recv = ftmac110_recv;
if (!eth_getenv_enetaddr_by_index("eth", card_nr, dev->enetaddr))
- eth_random_enetaddr(dev->enetaddr);
+ eth_random_addr(dev->enetaddr);
/* allocate tx descriptors (it must be 16 bytes aligned) */
chip->txd = dma_alloc_coherent(
diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c
index abd4e5b463..d509e30d35 100644
--- a/drivers/net/phy/atheros.c
+++ b/drivers/net/phy/atheros.c
@@ -31,9 +31,7 @@ static int ar8035_config(struct phy_device *phydev)
regval = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, (regval|0x0100));
- genphy_config_aneg(phydev);
-
- phy_reset(phydev);
+ phydev->supported = phydev->drv->features;
return 0;
}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index c691fbbbc6..230ed97dd1 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -18,6 +18,7 @@
#include <phy.h>
#include <errno.h>
#include <linux/err.h>
+#include <linux/compiler.h>
/* Generic PHY support and helper functions */
@@ -577,7 +578,7 @@ static struct phy_device *phy_device_create(struct mii_dev *bus, int addr,
* Description: Reads the ID registers of the PHY at @addr on the
* @bus, stores it in @phy_id and returns zero on success.
*/
-static int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+int __weak get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
{
int phy_reg;
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
index 3a55d271a5..c58fe50b72 100644
--- a/drivers/net/phy/vitesse.c
+++ b/drivers/net/phy/vitesse.c
@@ -58,6 +58,14 @@
#define MIIM_VSC8514_18G_QSGMII 0x80e0
#define MIIM_VSC8514_18G_CMDSTAT 0x8000
+/* Vitesse VSC8664 Control/Status Register */
+#define MIIM_VSC8664_SERDES_AND_SIGDET 0x13
+#define MIIM_VSC8664_ADDITIONAL_DEV 0x16
+#define MIIM_VSC8664_EPHY_CON 0x17
+#define MIIM_VSC8664_LED_CON 0x1E
+
+#define PHY_EXT_PAGE_ACCESS_EXTENDED 0x0001
+
/* CIS8201 */
static int vitesse_config(struct phy_device *phydev)
{
@@ -244,6 +252,33 @@ static int vsc8514_config(struct phy_device *phydev)
return 0;
}
+static int vsc8664_config(struct phy_device *phydev)
+{
+ u32 val;
+
+ /* Enable MAC interface auto-negotiation */
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON);
+ val |= (1 << 13);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON, val);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
+ PHY_EXT_PAGE_ACCESS_EXTENDED);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET);
+ val |= (1 << 11);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET, val);
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+
+ /* Enable LED blink */
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON);
+ val &= ~(1 << 2);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON, val);
+
+ genphy_config_aneg(phydev);
+
+ return 0;
+}
+
static struct phy_driver VSC8211_driver = {
.name = "Vitesse VSC8211",
.uid = 0xfc4b0,
@@ -334,6 +369,16 @@ static struct phy_driver VSC8662_driver = {
.shutdown = &genphy_shutdown,
};
+static struct phy_driver VSC8664_driver = {
+ .name = "Vitesse VSC8664",
+ .uid = 0x70660,
+ .mask = 0xffff0,
+ .features = PHY_GBIT_FEATURES,
+ .config = &vsc8664_config,
+ .startup = &vitesse_startup,
+ .shutdown = &genphy_shutdown,
+};
+
/* Vitesse bought Cicada, so we'll put these here */
static struct phy_driver cis8201_driver = {
.name = "CIS8201",
@@ -366,6 +411,7 @@ int phy_vitesse_init(void)
phy_register(&VSC8574_driver);
phy_register(&VSC8514_driver);
phy_register(&VSC8662_driver);
+ phy_register(&VSC8664_driver);
phy_register(&cis8201_driver);
phy_register(&cis8204_driver);
diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c
index 6317fb1324..3a41b0ec17 100644
--- a/drivers/pci/fsl_pci_init.c
+++ b/drivers/pci/fsl_pci_init.c
@@ -49,8 +49,13 @@ static void set_inbound_window(volatile pit_t *pi,
u64 size)
{
u32 sz = (__ilog2_u64(size) - 1);
- u32 flag = PIWAR_EN | PIWAR_LOCAL |
- PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP;
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
+ u32 flag = 0;
+#else
+ u32 flag = PIWAR_LOCAL;
+#endif
+
+ flag |= PIWAR_EN | PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP;
out_be32(&pi->pitar, r->phys_start >> 12);
out_be32(&pi->piwbar, r->bus_start >> 12);
diff --git a/drivers/power/tps6586x.c b/drivers/power/tps6586x.c
index 704c2439b1..d29d969533 100644
--- a/drivers/power/tps6586x.c
+++ b/drivers/power/tps6586x.c
@@ -32,7 +32,7 @@ enum {
};
#define MAX_I2C_RETRY 3
-int tps6586x_read(int reg)
+static int tps6586x_read(int reg)
{
int i;
uchar data;
@@ -61,7 +61,7 @@ exit:
return retval;
}
-int tps6586x_write(int reg, uchar *data, uint len)
+static int tps6586x_write(int reg, uchar *data, uint len)
{
int i;
int retval = -1;
diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c
index b1da75ec4d..9c5fbd1d69 100644
--- a/drivers/qe/qe.c
+++ b/drivers/qe/qe.c
@@ -14,6 +14,8 @@
#include "asm/immap_qe.h"
#include "qe.h"
+#define MPC85xx_DEVDISR_QE_DISABLE 0x1
+
qe_map_t *qe_immr = NULL;
static qe_snum_t snums[QE_NUM_OF_SNUM];
@@ -317,7 +319,9 @@ int qe_upload_firmware(const struct qe_firmware *firmware)
size_t calc_size = sizeof(struct qe_firmware);
size_t length;
const struct qe_header *hdr;
-
+#ifdef CONFIG_DEEP_SLEEP
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
if (!firmware) {
printf("Invalid address\n");
return -EINVAL;
@@ -330,6 +334,9 @@ int qe_upload_firmware(const struct qe_firmware *firmware)
if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') ||
(hdr->magic[2] != 'F')) {
printf("Not a microcode\n");
+#ifdef CONFIG_DEEP_SLEEP
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_QE_DISABLE);
+#endif
return -EPERM;
}
diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
index 8a13454943..f26979dbe1 100644
--- a/drivers/serial/ns16550.c
+++ b/drivers/serial/ns16550.c
@@ -33,6 +33,12 @@
#if defined(CONFIG_K2HK_EVM)
#define UART_REG_VAL_PWREMU_MGMT_UART_DISABLE 0
#define UART_REG_VAL_PWREMU_MGMT_UART_ENABLE ((1 << 14) | (1 << 13) | (1 << 0))
+#undef UART_MCRVAL
+#ifdef CONFIG_SERIAL_HW_FLOW_CONTROL
+#define UART_MCRVAL (UART_MCR_RTS | UART_MCR_AFE)
+#else
+#define UART_MCRVAL (UART_MCR_RTS)
+#endif
#endif
#ifndef CONFIG_SYS_NS16550_IER
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index c4fb59cfb3..fd61a5e545 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -74,9 +74,6 @@ static int on_baudrate(const char *name, const char *value, enum env_op op,
}
gd->baudrate = baudrate;
-#if defined(CONFIG_PPC) || defined(CONFIG_MCF52x2)
- gd->bd->bi_baudrate = baudrate;
-#endif
serial_setbrg();
@@ -502,12 +499,11 @@ int uart_post_test(int flags)
unsigned char c;
int ret, saved_baud, b;
struct serial_device *saved_dev, *s;
- bd_t *bd = gd->bd;
/* Save current serial state */
ret = 0;
saved_dev = serial_current;
- saved_baud = bd->bi_baudrate;
+ saved_baud = gd->baudrate;
for (s = serial_devices; s; s = s->next) {
/* If this driver doesn't support loop back, skip it */
@@ -530,7 +526,7 @@ int uart_post_test(int flags)
/* Test every available baud rate */
for (b = 0; b < ARRAY_SIZE(bauds); ++b) {
- bd->bi_baudrate = bauds[b];
+ gd->baudrate = bauds[b];
serial_setbrg();
/*
@@ -572,7 +568,7 @@ int uart_post_test(int flags)
done:
/* Restore previous serial state */
serial_current = saved_dev;
- bd->bi_baudrate = saved_baud;
+ gd->baudrate = saved_baud;
serial_reinit_all();
serial_setbrg();
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 6cb4d98668..45062e699b 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -104,15 +104,20 @@ int ehci_hcd_init(int index, enum usb_init_type init,
if (!strncmp(phy_type, "utmi", 4)) {
#if defined(CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY)
- setbits_be32(&ehci->control, PHY_CLK_SEL_UTMI);
- setbits_be32(&ehci->control, UTMI_PHY_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ PHY_CLK_SEL_UTMI);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ UTMI_PHY_EN);
udelay(1000); /* delay required for PHY Clk to appear */
#endif
out_le32(&(*hcor)->or_portsc[0], PORT_PTS_UTMI);
- setbits_be32(&ehci->control, USB_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ USB_EN);
} else {
- setbits_be32(&ehci->control, PHY_CLK_SEL_ULPI);
- clrsetbits_be32(&ehci->control, UTMI_PHY_EN, USB_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ PHY_CLK_SEL_ULPI);
+ clrsetbits_be32(&ehci->control, UTMI_PHY_EN |
+ CONTROL_REGISTER_W1C_MASK, USB_EN);
udelay(1000); /* delay required for PHY Clk to appear */
if (!usb_phy_clk_valid(ehci))
return -EINVAL;
diff --git a/drivers/video/atmel_hlcdfb.c b/drivers/video/atmel_hlcdfb.c
index 853303b5e5..bb4d7d8c14 100644
--- a/drivers/video/atmel_hlcdfb.c
+++ b/drivers/video/atmel_hlcdfb.c
@@ -128,12 +128,12 @@ void lcd_ctrl_init(void *lcdbase)
value |= LCDC_LCDCFG1_HSPW(panel_info.vl_hsync_len - 1);
lcdc_writel(&regs->lcdc_lcdcfg1, value);
- value = LCDC_LCDCFG2_VBPW(panel_info.vl_lower_margin);
- value |= LCDC_LCDCFG2_VFPW(panel_info.vl_upper_margin - 1);
+ value = LCDC_LCDCFG2_VBPW(panel_info.vl_upper_margin);
+ value |= LCDC_LCDCFG2_VFPW(panel_info.vl_lower_margin - 1);
lcdc_writel(&regs->lcdc_lcdcfg2, value);
- value = LCDC_LCDCFG3_HBPW(panel_info.vl_right_margin - 1);
- value |= LCDC_LCDCFG3_HFPW(panel_info.vl_left_margin - 1);
+ value = LCDC_LCDCFG3_HBPW(panel_info.vl_left_margin - 1);
+ value |= LCDC_LCDCFG3_HFPW(panel_info.vl_right_margin - 1);
lcdc_writel(&regs->lcdc_lcdcfg3, value);
/* Display size */
diff --git a/drivers/video/mxc_ipuv3_fb.c b/drivers/video/mxc_ipuv3_fb.c
index 3e21fb2306..f75d77064e 100644
--- a/drivers/video/mxc_ipuv3_fb.c
+++ b/drivers/video/mxc_ipuv3_fb.c
@@ -13,6 +13,7 @@
#include <common.h>
#include <asm/errno.h>
+#include <asm/global_data.h>
#include <linux/string.h>
#include <linux/list.h>
#include <linux/fb.h>
@@ -24,6 +25,8 @@
#include "mxcfb.h"
#include "ipu_regs.h"
+DECLARE_GLOBAL_DATA_PTR;
+
static int mxcfb_map_video_memory(struct fb_info *fbi);
static int mxcfb_unmap_video_memory(struct fb_info *fbi);
@@ -415,6 +418,8 @@ static int mxcfb_map_video_memory(struct fb_info *fbi)
fbi->screen_size = fbi->fix.smem_len;
+ gd->fb_base = fbi->fix.smem_start;
+
/* Clear the screen */
memset((char *)fbi->screen_base, 0, fbi->fix.smem_len);
generated by cgit (git 2.34.1) at 2024-12-25 14:29:08 +0000