diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/block/Makefile | 1 | ||||
| -rw-r--r-- | drivers/block/fsl_sata.c | 8 | ||||
| -rw-r--r-- | drivers/block/sata_sil3114.c | 839 | ||||
| -rw-r--r-- | drivers/block/sata_sil3114.h | 147 | ||||
| -rw-r--r-- | drivers/pcmcia/Makefile | 6 | ||||
| -rw-r--r-- | drivers/pcmcia/marubun_pcmcia.c | 7 | ||||
| -rw-r--r-- | drivers/pcmcia/pxa_pcmcia.c | 4 | ||||
| -rw-r--r-- | drivers/pcmcia/ti_pci1410a.c | 4 | ||||
| -rw-r--r-- | drivers/serial/serial_pl010.c | 8 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 2 | ||||
| -rw-r--r-- | drivers/spi/mpc8xxx_spi.c | 2 |
11 files changed, 1010 insertions, 18 deletions
diff --git a/drivers/block/Makefile b/drivers/block/Makefile index 5f1298dcdc..a09cd2a603 100644 --- a/drivers/block/Makefile +++ b/drivers/block/Makefile @@ -29,6 +29,7 @@ COBJS-y += ahci.o COBJS-y += ata_piix.o COBJS-$(CONFIG_FSL_SATA) += fsl_sata.o COBJS-$(CONFIG_LIBATA) += libata.o +COBJS-$(CONFIG_SATA_SIL3114) += sata_sil3114.o COBJS-y += sil680.o COBJS-y += sym53c8xx.o COBJS-y += systemace.o diff --git a/drivers/block/fsl_sata.c b/drivers/block/fsl_sata.c index d14f5bc6bf..d441a30ed5 100644 --- a/drivers/block/fsl_sata.c +++ b/drivers/block/fsl_sata.c @@ -248,6 +248,10 @@ int init_sata(int dev) else printf(" %s ", sata->name); + /* Wait PHY RDY signal changed for 500ms */ + ata_wait_register(®->hstatus, HSTATUS_PHY_RDY, + HSTATUS_PHY_RDY, 500); + /* Check PHYRDY */ val32 = in_le32(®->hstatus); if (val32 & HSTATUS_PHY_RDY) { @@ -258,6 +262,10 @@ int init_sata(int dev) return -1; } + /* Wait for signature updated, which is 1st D2H */ + ata_wait_register(®->hstatus, HSTATUS_SIGNATURE, + HSTATUS_SIGNATURE, 10000); + if (val32 & HSTATUS_SIGNATURE) { sig = in_le32(®->sig); debug("Signature updated, the sig =%08x\n\r", sig); diff --git a/drivers/block/sata_sil3114.c b/drivers/block/sata_sil3114.c new file mode 100644 index 0000000000..8399737ff5 --- /dev/null +++ b/drivers/block/sata_sil3114.c @@ -0,0 +1,839 @@ +/* + * Copyright (C) Excito Elektronik i Skåne AB, All rights reserved. + * Author: Tor Krill <tor@excito.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * This is a driver for Silicon Image sil3114 sata chip modelled on + * the ata_piix driver + */ + +#include <common.h> +#include <pci.h> +#include <command.h> +#include <config.h> +#include <asm/byteorder.h> +#include <asm/io.h> +#include <ide.h> +#include <libata.h> +#include "sata_sil3114.h" + +/* Convert sectorsize to wordsize */ +#define ATA_SECTOR_WORDS (ATA_SECT_SIZE/2) + +/* Forwards */ +u8 sil3114_spin_up (int num); +u8 sil3114_spin_down (int num); +static int sata_bus_softreset (int num); +static void sata_identify (int num, int dev); +static u8 check_power_mode (int num); +static void sata_port (struct sata_ioports *ioport); +static void set_Feature_cmd (int num, int dev); +static u8 sata_busy_wait (struct sata_ioports *ioaddr, int bits, + unsigned int max, u8 usealtstatus); +static u8 sata_chk_status (struct sata_ioports *ioaddr, u8 usealtstatus); +static void msleep (int count); + +static u32 iobase[6] = { 0, 0, 0, 0, 0, 0}; /* PCI BAR registers for device */ +extern block_dev_desc_t sata_dev_desc[CFG_SATA_MAX_DEVICE]; + +static struct sata_port port[CFG_SATA_MAX_DEVICE]; + +static void output_data (struct sata_ioports *ioaddr, u16 * sect_buf, int words) +{ + while (words--) { + __raw_writew (*sect_buf++, (void *)ioaddr->data_addr); + } +} + +static int input_data (struct sata_ioports *ioaddr, u16 * sect_buf, int words) +{ + while (words--) { + *sect_buf++ = __raw_readw ((void *)ioaddr->data_addr); + } + return 0; +} + +static int sata_bus_softreset (int num) +{ + u8 status = 0; + + port[num].dev_mask = 1; + + port[num].ctl_reg = 0x08; /*Default value of control reg */ + writeb (port[num].ctl_reg, port[num].ioaddr.ctl_addr); + udelay (10); + writeb (port[num].ctl_reg | ATA_SRST, port[num].ioaddr.ctl_addr); + udelay (10); + writeb (port[num].ctl_reg, port[num].ioaddr.ctl_addr); + + /* spec mandates ">= 2ms" before checking status. + * We wait 150ms, because that was the magic delay used for + * ATAPI devices in Hale Landis's ATADRVR, for the period of time + * between when the ATA command register is written, and then + * status is checked. Because waiting for "a while" before + * checking status is fine, post SRST, we perform this magic + * delay here as well. + */ + msleep (150); + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 300, 0); + while ((status & ATA_BUSY)) { + msleep (100); + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 3, 0); + } + + if (status & ATA_BUSY) { + printf ("ata%u is slow to respond,plz be patient\n", port); + } + + while ((status & ATA_BUSY)) { + msleep (100); + status = sata_chk_status (&port[num].ioaddr, 0); + } + + if (status & ATA_BUSY) { + printf ("ata%u failed to respond : ", port); + printf ("bus reset failed\n"); + port[num].dev_mask = 0; + return 1; + } + return 0; +} + +static void sata_identify (int num, int dev) +{ + u8 cmd = 0, status = 0, devno = num; + u16 iobuf[ATA_SECTOR_WORDS]; + u64 n_sectors = 0; + + memset (iobuf, 0, sizeof (iobuf)); + + if (!(port[num].dev_mask & 0x01)) { + printf ("dev%d is not present on port#%d\n", dev, num); + return; + } + + debug ("port=%d dev=%d\n", num, dev); + + status = 0; + cmd = ATA_CMD_ID_ATA; /*Device Identify Command */ + writeb (cmd, port[num].ioaddr.command_addr); + readb (port[num].ioaddr.altstatus_addr); + udelay (10); + + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 1000, 0); + if (status & ATA_ERR) { + printf ("\ndevice not responding\n"); + port[num].dev_mask &= ~0x01; + return; + } + + input_data (&port[num].ioaddr, iobuf, ATA_SECTOR_WORDS); + + ata_swap_buf_le16 (iobuf, ATA_SECTOR_WORDS); + + debug ("Specific config: %x\n", iobuf[2]); + + /* we require LBA and DMA support (bits 8 & 9 of word 49) */ + if (!ata_id_has_dma (iobuf) || !ata_id_has_lba (iobuf)) { + debug ("ata%u: no dma/lba\n", num); + } +#ifdef DEBUG + ata_dump_id (iobuf); +#endif + n_sectors = ata_id_n_sectors (iobuf); + + if (n_sectors == 0) { + port[num].dev_mask &= ~0x01; + return; + } + ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].revision, + ATA_ID_FW_REV, sizeof (sata_dev_desc[devno].revision)); + ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].vendor, + ATA_ID_PROD, sizeof (sata_dev_desc[devno].vendor)); + ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].product, + ATA_ID_SERNO, sizeof (sata_dev_desc[devno].product)); + + /* TODO - atm we asume harddisk ie not removable */ + sata_dev_desc[devno].removable = 0; + + sata_dev_desc[devno].lba = (u32) n_sectors; + debug ("lba=0x%x\n", sata_dev_desc[devno].lba); + +#ifdef CONFIG_LBA48 + if (iobuf[83] & (1 << 10)) { + sata_dev_desc[devno].lba48 = 1; + } else { + sata_dev_desc[devno].lba48 = 0; + } +#endif + + /* assuming HD */ + sata_dev_desc[devno].type = DEV_TYPE_HARDDISK; + sata_dev_desc[devno].blksz = ATA_SECT_SIZE; + sata_dev_desc[devno].lun = 0; /* just to fill something in... */ +} + +static void set_Feature_cmd (int num, int dev) +{ + u8 status = 0; + + if (!(port[num].dev_mask & 0x01)) { + debug ("dev%d is not present on port#%d\n", dev, num); + return; + } + + writeb (SETFEATURES_XFER, port[num].ioaddr.feature_addr); + writeb (XFER_PIO_4, port[num].ioaddr.nsect_addr); + writeb (0, port[num].ioaddr.lbal_addr); + writeb (0, port[num].ioaddr.lbam_addr); + writeb (0, port[num].ioaddr.lbah_addr); + + writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr); + writeb (ATA_CMD_SET_FEATURES, port[num].ioaddr.command_addr); + + udelay (50); + msleep (150); + + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 5000, 0); + if ((status & (ATA_BUSY | ATA_ERR))) { + printf ("Error : status 0x%02x\n", status); + port[num].dev_mask &= ~0x01; + } +} + +u8 sil3114_spin_down (int num) +{ + u8 status = 0; + + debug ("Spin down disk\n"); + + if (!(port[num].dev_mask & 0x01)) { + debug ("Device ata%d is not present\n", num); + return 1; + } + + if ((status = check_power_mode (num)) == 0x00) { + debug ("Already in standby\n"); + return 0; + } + + if (status == 0x01) { + printf ("Failed to check power mode on ata%d\n", num); + return 1; + } + + if (!((status = sata_chk_status (&port[num].ioaddr, 0)) & ATA_DRDY)) { + printf ("Device ata%d not ready\n", num); + return 1; + } + + writeb (0x00, port[num].ioaddr.feature_addr); + + writeb (0x00, port[num].ioaddr.nsect_addr); + writeb (0x00, port[num].ioaddr.lbal_addr); + writeb (0x00, port[num].ioaddr.lbam_addr); + writeb (0x00, port[num].ioaddr.lbah_addr); + + writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr); + writeb (ATA_CMD_STANDBY, port[num].ioaddr.command_addr); + + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 30000, 0); + if ((status & (ATA_BUSY | ATA_ERR))) { + printf ("Error waiting for disk spin down: status 0x%02x\n", + status); + port[num].dev_mask &= ~0x01; + return 1; + } + return 0; +} + +u8 sil3114_spin_up (int num) +{ + u8 status = 0; + + debug ("Spin up disk\n"); + + if (!(port[num].dev_mask & 0x01)) { + debug ("Device ata%d is not present\n", num); + return 1; + } + + if ((status = check_power_mode (num)) != 0x00) { + if (status == 0x01) { + printf ("Failed to check power mode on ata%d\n", num); + return 1; + } else { + /* should be up and running already */ + return 0; + } + } + + if (!((status = sata_chk_status (&port[num].ioaddr, 0)) & ATA_DRDY)) { + printf ("Device ata%d not ready\n", num); + return 1; + } + + debug ("Stautus of device check: %d\n", status); + + writeb (0x00, port[num].ioaddr.feature_addr); + + writeb (0x00, port[num].ioaddr.nsect_addr); + writeb (0x00, port[num].ioaddr.lbal_addr); + writeb (0x00, port[num].ioaddr.lbam_addr); + writeb (0x00, port[num].ioaddr.lbah_addr); + + writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr); + writeb (ATA_CMD_IDLE, port[num].ioaddr.command_addr); + + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 30000, 0); + if ((status & (ATA_BUSY | ATA_ERR))) { + printf ("Error waiting for disk spin up: status 0x%02x\n", + status); + port[num].dev_mask &= ~0x01; + return 1; + } + + /* Wait for disk to enter Active state */ + do { + msleep (10); + status = check_power_mode (num); + } while ((status == 0x00) || (status == 0x80)); + + if (status == 0x01) { + printf ("Falied waiting for disk to spin up\n"); + return 1; + } + + return 0; +} + +/* Return value is not the usual here + * 0x00 - Device stand by + * 0x01 - Operation failed + * 0x80 - Device idle + * 0xff - Device active +*/ +static u8 check_power_mode (int num) +{ + u8 status = 0; + u8 res = 0; + if (!(port[num].dev_mask & 0x01)) { + debug ("Device ata%d is not present\n", num); + return 1; + } + + if (!(sata_chk_status (&port[num].ioaddr, 0) & ATA_DRDY)) { + printf ("Device ata%d not ready\n", num); + return 1; + } + + writeb (0, port[num].ioaddr.feature_addr); + writeb (0, port[num].ioaddr.nsect_addr); + writeb (0, port[num].ioaddr.lbal_addr); + writeb (0, port[num].ioaddr.lbam_addr); + writeb (0, port[num].ioaddr.lbah_addr); + + writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr); + writeb (ATA_CMD_CHK_POWER, port[num].ioaddr.command_addr); + + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 5000, 0); + if ((status & (ATA_BUSY | ATA_ERR))) { + printf + ("Error waiting for check power mode complete : status 0x%02x\n", + status); + port[num].dev_mask &= ~0x01; + return 1; + } + res = readb (port[num].ioaddr.nsect_addr); + debug ("Check powermode: %d\n", res); + return res; + +} + +static void sata_port (struct sata_ioports *ioport) +{ + ioport->data_addr = ioport->cmd_addr + ATA_REG_DATA; + ioport->error_addr = ioport->cmd_addr + ATA_REG_ERR; + ioport->feature_addr = ioport->cmd_addr + ATA_REG_FEATURE; + ioport->nsect_addr = ioport->cmd_addr + ATA_REG_NSECT; + ioport->lbal_addr = ioport->cmd_addr + ATA_REG_LBAL; + ioport->lbam_addr = ioport->cmd_addr + ATA_REG_LBAM; + ioport->lbah_addr = ioport->cmd_addr + ATA_REG_LBAH; + ioport->device_addr = ioport->cmd_addr + ATA_REG_DEVICE; + ioport->status_addr = ioport->cmd_addr + ATA_REG_STATUS; + ioport->command_addr = ioport->cmd_addr + ATA_REG_CMD; +} + +static u8 wait_for_irq (int num, unsigned int max) +{ + + u32 port = iobase[5]; + switch (num) { + case 0: + port += VND_TF_CNST_CH0; + break; + case 1: + port += VND_TF_CNST_CH1; + break; + case 2: + port += VND_TF_CNST_CH2; + break; + case 3: + port += VND_TF_CNST_CH3; + break; + default: + return 1; + } + + do { + if (readl (port) & VND_TF_CNST_INTST) { + break; + } + udelay (1000); + max--; + } while ((max > 0)); + + return (max == 0); +} + +static u8 sata_busy_wait (struct sata_ioports *ioaddr, int bits, + unsigned int max, u8 usealtstatus) +{ + u8 status; + + do { + if (!((status = sata_chk_status (ioaddr, usealtstatus)) & bits)) { + break; + } + udelay (1000); + max--; + } while ((status & bits) && (max > 0)); + + return status; +} + +static u8 sata_chk_status (struct sata_ioports *ioaddr, u8 usealtstatus) +{ + if (!usealtstatus) { + return readb (ioaddr->status_addr); + } else { + return readb (ioaddr->altstatus_addr); + } +} + +static void msleep (int count) +{ + int i; + + for (i = 0; i < count; i++) + udelay (1000); +} + +/* Read up to 255 sectors + * + * Returns sectors read +*/ +static u8 do_one_read (int device, ulong block, u8 blkcnt, u16 * buff, + uchar lba48) +{ + + u8 sr = 0; + u8 status; + u64 blknr = (u64) block; + + if (!(sata_chk_status (&port[device].ioaddr, 0) & ATA_DRDY)) { + printf ("Device ata%d not ready\n", device); + return 0; + } + + /* Set up transfer */ +#ifdef CONFIG_LBA48 + if (lba48) { + /* write high bits */ + writeb (0, port[device].ioaddr.nsect_addr); + writeb ((blknr >> 24) & 0xFF, port[device].ioaddr.lbal_addr); + writeb ((blknr >> 32) & 0xFF, port[device].ioaddr.lbam_addr); + writeb ((blknr >> 40) & 0xFF, port[device].ioaddr.lbah_addr); + } +#endif + writeb (blkcnt, port[device].ioaddr.nsect_addr); + writeb (((blknr) >> 0) & 0xFF, port[device].ioaddr.lbal_addr); + writeb ((blknr >> 8) & 0xFF, port[device].ioaddr.lbam_addr); + writeb ((blknr >> 16) & 0xFF, port[device].ioaddr.lbah_addr); + +#ifdef CONFIG_LBA48 + if (lba48) { + writeb (ATA_LBA, port[device].ioaddr.device_addr); + writeb (ATA_CMD_PIO_READ_EXT, port[device].ioaddr.command_addr); + } else +#endif + { + writeb (ATA_LBA | ((blknr >> 24) & 0xF), + port[device].ioaddr.device_addr); + writeb (ATA_CMD_PIO_READ, port[device].ioaddr.command_addr); + } + + status = sata_busy_wait (&port[device].ioaddr, ATA_BUSY, 10000, 1); + + if (status & ATA_BUSY) { + u8 err = 0; + + printf ("Device %d not responding status %d\n", device, status); + err = readb (port[device].ioaddr.error_addr); + printf ("Error reg = 0x%x\n", err); + + return (sr); + } + while (blkcnt--) { + + if (wait_for_irq (device, 500)) { + printf ("ata%u irq failed\n", device); + return sr; + } + + status = sata_chk_status (&port[device].ioaddr, 0); + if (status & ATA_ERR) { + printf ("ata%u error %d\n", device, + readb (port[device].ioaddr.error_addr)); + return sr; + } + /* Read one sector */ + input_data (&port[device].ioaddr, buff, ATA_SECTOR_WORDS); + buff += ATA_SECTOR_WORDS; + sr++; + + } + return sr; +} + +ulong sata_read (int device, ulong block, lbaint_t blkcnt, void *buff) +{ + ulong n = 0, sread; + u16 *buffer = (u16 *) buff; + u8 status = 0; + u64 blknr = (u64) block; + unsigned char lba48 = 0; + +#ifdef CONFIG_LBA48 + if (blknr > 0xfffffff) { + if (!sata_dev_desc[device].lba48) { + printf ("Drive doesn't support 48-bit addressing\n"); + return 0; + } + /* more than 28 bits used, use 48bit mode */ + lba48 = 1; + } +#endif + + while (blkcnt > 0) { + + if (blkcnt > 255) { + sread = 255; + } else { + sread = blkcnt; + } + + status = do_one_read (device, blknr, sread, buffer, lba48); + if (status != sread) { + printf ("Read failed\n"); + return n; + } + + blkcnt -= sread; + blknr += sread; + n += sread; + buffer += sread * ATA_SECTOR_WORDS; + } + return n; +} + +ulong sata_write (int device, ulong block, lbaint_t blkcnt, const void *buff) +{ + ulong n = 0; + u16 *buffer = (u16 *) buff; + unsigned char status = 0, num = 0; + u64 blknr = (u64) block; +#ifdef CONFIG_LBA48 + unsigned char lba48 = 0; + + if (blknr > 0xfffffff) { + if (!sata_dev_desc[device].lba48) { + printf ("Drive doesn't support 48-bit addressing\n"); + return 0; + } + /* more than 28 bits used, use 48bit mode */ + lba48 = 1; + } +#endif + /*Port Number */ + num = device; + + while (blkcnt-- > 0) { + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500, 0); + if (status & ATA_BUSY) { + printf ("ata%u failed to respond\n", port[num].port_no); + return n; + } +#ifdef CONFIG_LBA48 + if (lba48) { + /* write high bits */ + writeb (0, port[num].ioaddr.nsect_addr); + writeb ((blknr >> 24) & 0xFF, + port[num].ioaddr.lbal_addr); + writeb ((blknr >> 32) & 0xFF, + port[num].ioaddr.lbam_addr); + writeb ((blknr >> 40) & 0xFF, + port[num].ioaddr.lbah_addr); + } +#endif + writeb (1, port[num].ioaddr.nsect_addr); + writeb ((blknr >> 0) & 0xFF, port[num].ioaddr.lbal_addr); + writeb ((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr); + writeb ((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr); +#ifdef CONFIG_LBA48 + if (lba48) { + writeb (ATA_LBA, port[num].ioaddr.device_addr); + writeb (ATA_CMD_PIO_WRITE_EXT, port[num].ioaddr.command_addr); + } else +#endif + { + writeb (ATA_LBA | ((blknr >> 24) & 0xF), + port[num].ioaddr.device_addr); + writeb (ATA_CMD_PIO_WRITE, port[num].ioaddr.command_addr); + } + + msleep (50); + /*may take up to 4 sec */ + status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 4000, 0); + if ((status & (ATA_DRQ | ATA_BUSY | ATA_ERR)) != ATA_DRQ) { + printf ("Error no DRQ dev %d blk %ld: sts 0x%02x\n", + device, (ulong) blknr, status); + return (n); + } + + output_data (&port[num].ioaddr, buffer, ATA_SECTOR_WORDS); + readb (port[num].ioaddr.altstatus_addr); + udelay (50); + + ++n; + ++blknr; + buffer += ATA_SECTOR_WORDS; + } + return n; +} + +/* Driver implementation */ +static u8 sil_get_device_cache_line (pci_dev_t pdev) +{ + u8 cache_line = 0; + pci_read_config_byte (pdev, PCI_CACHE_LINE_SIZE, &cache_line); + return cache_line; +} + +int init_sata (int dev) +{ + static u8 init_done = 0; + static int res = 1; + pci_dev_t devno; + u8 cls = 0; + u16 cmd = 0; + u32 sconf = 0; + + if (init_done) { + return res; + } + + init_done = 1; + + if ((devno = pci_find_device (SIL_VEND_ID, SIL3114_DEVICE_ID, 0)) == -1) { + res = 1; + return res; + } + + /* Read out all BARs, even though we only use MMIO from BAR5 */ + pci_read_config_dword (devno, PCI_BASE_ADDRESS_0, &iobase[0]); + pci_read_config_dword (devno, PCI_BASE_ADDRESS_1, &iobase[1]); + pci_read_config_dword (devno, PCI_BASE_ADDRESS_2, &iobase[2]); + pci_read_config_dword (devno, PCI_BASE_ADDRESS_3, &iobase[3]); + pci_read_config_dword (devno, PCI_BASE_ADDRESS_4, &iobase[4]); + pci_read_config_dword (devno, PCI_BASE_ADDRESS_5, &iobase[5]); + + if ((iobase[0] == 0xFFFFFFFF) || (iobase[1] == 0xFFFFFFFF) || + (iobase[2] == 0xFFFFFFFF) || (iobase[3] == 0xFFFFFFFF) || + (iobase[4] == 0xFFFFFFFF) || (iobase[5] == 0xFFFFFFFF)) { + printf ("Error no base addr for SATA controller\n"); + res = 1; + return res; + } + + /* mask off unused bits */ + iobase[0] &= 0xfffffffc; + iobase[1] &= 0xfffffff8; + iobase[2] &= 0xfffffffc; + iobase[3] &= 0xfffffff8; + iobase[4] &= 0xfffffff0; + iobase[5] &= 0xfffffc00; + + /* from sata_sil in Linux kernel */ + cls = sil_get_device_cache_line (devno); + if (cls) { + cls >>= 3; + cls++; /* cls = (line_size/8)+1 */ + writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH0); + writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH1); + writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH2); + writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH3); + } else { + printf ("Cache line not set. Driver may not function\n"); + } + + /* Enable operation */ + pci_read_config_word (devno, PCI_COMMAND, &cmd); + cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY; + pci_write_config_word (devno, PCI_COMMAND, cmd); + + /* Disable interrupt usage */ + pci_read_config_dword (devno, VND_SYSCONFSTAT, &sconf); + sconf |= (VND_SYSCONFSTAT_CHN_0_INTBLOCK | VND_SYSCONFSTAT_CHN_1_INTBLOCK); + pci_write_config_dword (devno, VND_SYSCONFSTAT, sconf); + + res = 0; + return res; +} + +/* Check if device is connected to port */ +int sata_bus_probe (int portno) +{ + u32 port = iobase[5]; + u32 val; + switch (portno) { + case 0: + port += VND_SSTATUS_CH0; + break; + case 1: + port += VND_SSTATUS_CH1; + break; + case 2: + port += VND_SSTATUS_CH2; + break; + case 3: + port += VND_SSTATUS_CH3; + break; + default: + return 0; + } + val = readl (port); + if ((val & SATA_DET_PRES) == SATA_DET_PRES) { + return 1; + } else { + return 0; + } +} + +int sata_phy_reset (int portno) +{ + u32 port = iobase[5]; + u32 val; + switch (portno) { + case 0: + port += VND_SCONTROL_CH0; + break; + case 1: + port += VND_SCONTROL_CH1; + break; + case 2: + port += VND_SCONTROL_CH2; + break; + case 3: + port += VND_SCONTROL_CH3; + break; + default: + return 0; + } + val = readl (port); + writel (val | SATA_SC_DET_RST, port); + msleep (150); + writel (val & ~SATA_SC_DET_RST, port); + return 0; +} + +int scan_sata (int dev) +{ + /* A bit brain dead, but the code has a legacy */ + switch (dev) { + case 0: + port[0].port_no = 0; + port[0].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH0; + port[0].ioaddr.altstatus_addr = port[0].ioaddr.ctl_addr = + (iobase[5] + VND_TF2_CH0) | ATA_PCI_CTL_OFS; + port[0].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH0; + break; + case 1: + port[1].port_no = 0; + port[1].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH1; + port[1].ioaddr.altstatus_addr = port[1].ioaddr.ctl_addr = + (iobase[5] + VND_TF2_CH1) | ATA_PCI_CTL_OFS; + port[1].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH1; + break; + case 2: + port[2].port_no = 0; + port[2].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH2; + port[2].ioaddr.altstatus_addr = port[2].ioaddr.ctl_addr = + (iobase[5] + VND_TF2_CH2) | ATA_PCI_CTL_OFS; + port[2].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH2; + break; + case 3: + port[3].port_no = 0; + port[3].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH3; + port[3].ioaddr.altstatus_addr = port[3].ioaddr.ctl_addr = + (iobase[5] + VND_TF2_CH3) | ATA_PCI_CTL_OFS; + port[3].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH3; + break; + default: + printf ("Tried to scan unknown port: ata%d\n", dev); + return 1; + } + + /* Initialize other registers */ + sata_port (&port[dev].ioaddr); + + /* Check for attached device */ + if (!sata_bus_probe (dev)) { + port[dev].port_state = 0; + debug ("SATA#%d port is not present\n", dev); + } else { + debug ("SATA#%d port is present\n", dev); + if (sata_bus_softreset (dev)) { + /* soft reset failed, try a hard one */ + sata_phy_reset (dev); + if (sata_bus_softreset (dev)) { + port[dev].port_state = 0; + } else { + port[dev].port_state = 1; + } + } else { + port[dev].port_state = 1; + } + } + if (port[dev].port_state == 1) { + /* Probe device and set xfer mode */ + sata_identify (dev, 0); + set_Feature_cmd (dev, 0); + } + + return 0; +} diff --git a/drivers/block/sata_sil3114.h b/drivers/block/sata_sil3114.h new file mode 100644 index 0000000000..8f2301ac95 --- /dev/null +++ b/drivers/block/sata_sil3114.h @@ -0,0 +1,147 @@ +/* + * Copyright (C) Excito Elektronik i Skåne AB, All rights reserved. + * Author: Tor Krill <tor@excito.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef SATA_SIL3114_H +#define SATA_SIL3114_H + +struct sata_ioports { + unsigned long cmd_addr; + unsigned long data_addr; + unsigned long error_addr; + unsigned long feature_addr; + unsigned long nsect_addr; + unsigned long lbal_addr; + unsigned long lbam_addr; + unsigned long lbah_addr; + unsigned long device_addr; + unsigned long status_addr; + unsigned long command_addr; + unsigned long altstatus_addr; + unsigned long ctl_addr; + unsigned long bmdma_addr; + unsigned long scr_addr; +}; + +struct sata_port { + unsigned char port_no; /* primary=0, secondary=1 */ + struct sata_ioports ioaddr; /* ATA cmd/ctl/dma reg blks */ + unsigned char ctl_reg; + unsigned char last_ctl; + unsigned char port_state; /* 1-port is available and */ + /* 0-port is not available */ + unsigned char dev_mask; +}; + +/* Missing ata defines */ +#define ATA_CMD_STANDBY 0xE2 +#define ATA_CMD_STANDBYNOW1 0xE0 +#define ATA_CMD_IDLE 0xE3 +#define ATA_CMD_IDLEIMMEDIATE 0xE1 + +/* Defines for SIL3114 chip */ + +/* PCI defines */ +#define SIL_VEND_ID 0x1095 +#define SIL3114_DEVICE_ID 0x3114 + +/* some vendor specific registers */ +#define VND_SYSCONFSTAT 0x88 /* System Configuration Status and Command */ +#define VND_SYSCONFSTAT_CHN_0_INTBLOCK (1<<22) +#define VND_SYSCONFSTAT_CHN_1_INTBLOCK (1<<23) +#define VND_SYSCONFSTAT_CHN_2_INTBLOCK (1<<24) +#define VND_SYSCONFSTAT_CHN_3_INTBLOCK (1<<25) + +/* internal registers mapped by BAR5 */ +/* SATA Control*/ +#define VND_SCONTROL_CH0 0x100 +#define VND_SCONTROL_CH1 0x180 +#define VND_SCONTROL_CH2 0x300 +#define VND_SCONTROL_CH3 0x380 + +#define SATA_SC_IPM_T2P (1<<16) +#define SATA_SC_IPM_T2S (2<<16) +#define SATA_SC_SPD_1_5 (1<<4) +#define SATA_SC_SPD_3_0 (2<<4) +#define SATA_SC_DET_RST (1) /* ATA Reset sequence */ +#define SATA_SC_DET_PDIS (4) /* PHY Disable */ + +/* SATA Status */ +#define VND_SSTATUS_CH0 0x104 +#define VND_SSTATUS_CH1 0x184 +#define VND_SSTATUS_CH2 0x304 +#define VND_SSTATUS_CH3 0x384 + +#define SATA_SS_IPM_ACTIVE (1<<8) +#define SATA_SS_IPM_PARTIAL (2<<8) +#define SATA_SS_IPM_SLUMBER (6<<8) +#define SATA_SS_SPD_1_5 (1<<4) +#define SATA_SS_SPD_3_0 (2<<4) +#define SATA_DET_P_NOPHY (1) /* Device presence but no PHY connection established */ +#define SATA_DET_PRES (3) /* Device presence and active PHY */ +#define SATA_DET_OFFLINE (4) /* Device offline or in loopback mode */ + +/* Task file registers in BAR5 mapping */ +#define VND_TF0_CH0 0x80 +#define VND_TF0_CH1 0xc0 +#define VND_TF0_CH2 0x280 +#define VND_TF0_CH3 0x2c0 +#define VND_TF1_CH0 0x88 +#define VND_TF1_CH1 0xc8 +#define VND_TF1_CH2 0x288 +#define VND_TF1_CH3 0x2c8 +#define VND_TF2_CH0 0x88 +#define VND_TF2_CH1 0xc8 +#define VND_TF2_CH2 0x288 +#define VND_TF2_CH3 0x2c8 + +#define VND_BMDMA_CH0 0x00 +#define VND_BMDMA_CH1 0x08 +#define VND_BMDMA_CH2 0x200 +#define VND_BMDMA_CH3 0x208 +#define VND_BMDMA2_CH0 0x10 +#define VND_BMDMA2_CH1 0x18 +#define VND_BMDMA2_CH2 0x210 +#define VND_BMDMA2_CH3 0x218 + +/* FIFO control */ +#define VND_FIFOCFG_CH0 0x40 +#define VND_FIFOCFG_CH1 0x44 +#define VND_FIFOCFG_CH2 0x240 +#define VND_FIFOCFG_CH3 0x244 + +/* Task File configuration and status */ +#define VND_TF_CNST_CH0 0xa0 +#define VND_TF_CNST_CH1 0xe0 +#define VND_TF_CNST_CH2 0x2a0 +#define VND_TF_CNST_CH3 0x2e0 + +#define VND_TF_CNST_BFCMD (1<<1) +#define VND_TF_CNST_CHNRST (1<<2) +#define VND_TF_CNST_VDMA (1<<10) +#define VND_TF_CNST_INTST (1<<11) +#define VND_TF_CNST_WDTO (1<<12) +#define VND_TF_CNST_WDEN (1<<13) +#define VND_TF_CNST_WDIEN (1<<14) + +/* for testing */ +#define VND_SSDR 0x04c /* System Software Data Register */ +#define VND_FMACS 0x050 /* Flash Memory Address control and status */ + +#endif diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile index ac4378a0bd..ba251d0984 100644 --- a/drivers/pcmcia/Makefile +++ b/drivers/pcmcia/Makefile @@ -27,11 +27,11 @@ LIB := $(obj)libpcmcia.a COBJS-$(CONFIG_I82365) += i82365.o COBJS-y += mpc8xx_pcmcia.o -COBJS-y += pxa_pcmcia.o +COBJS-$(CONFIG_PXA_PCMCIA) += pxa_pcmcia.o COBJS-y += rpx_pcmcia.o -COBJS-y += ti_pci1410a.o +COBJS-$(CONFIG_IDE_TI_CARDBUS) += ti_pci1410a.o COBJS-y += tqm8xx_pcmcia.o -COBJS-y += marubun_pcmcia.o +COBJS-$(CONFIG_MARUBUN_PCCARD) += marubun_pcmcia.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/pcmcia/marubun_pcmcia.c b/drivers/pcmcia/marubun_pcmcia.c index a213092334..d075ba37cd 100644 --- a/drivers/pcmcia/marubun_pcmcia.c +++ b/drivers/pcmcia/marubun_pcmcia.c @@ -31,12 +31,11 @@ #define CONFIG_PCMCIA #endif -#if defined(CONFIG_CMD_IDE) +#if defined(CONFIG_CMD_IDE) #define CONFIG_PCMCIA #endif -#if defined(CONFIG_PCMCIA) \ - && (defined(CONFIG_MARUBUN_PCCARD)) +#if defined(CONFIG_PCMCIA) /* MR-SHPC-01 register */ #define MRSHPC_MODE (CFG_MARUBUN_MRSHPC + 4) @@ -112,4 +111,4 @@ int pcmcia_off (void) return 0; } -#endif /* CONFIG_MARUBUN_PCCARD */ +#endif /* CONFIG_PCMCIA */ diff --git a/drivers/pcmcia/pxa_pcmcia.c b/drivers/pcmcia/pxa_pcmcia.c index 65427efdbd..11d8590d7b 100644 --- a/drivers/pcmcia/pxa_pcmcia.c +++ b/drivers/pcmcia/pxa_pcmcia.c @@ -1,8 +1,6 @@ #include <common.h> #include <config.h> -#ifdef CONFIG_PXA_PCMCIA - #include <pcmcia.h> #include <asm/arch/pxa-regs.h> #include <asm/io.h> @@ -93,5 +91,3 @@ int pcmcia_off (void) return 0; } #endif - -#endif /* CONFIG_PXA_PCMCIA */ diff --git a/drivers/pcmcia/ti_pci1410a.c b/drivers/pcmcia/ti_pci1410a.c index 208ca50a74..c876d0c402 100644 --- a/drivers/pcmcia/ti_pci1410a.c +++ b/drivers/pcmcia/ti_pci1410a.c @@ -64,7 +64,7 @@ #include <pcmcia.h> -#if defined(CONFIG_CMD_PCMCIA) && defined(CONFIG_IDE_TI_CARDBUS) +#if defined(CONFIG_CMD_PCMCIA) int pcmcia_on(int ide_base_bus); @@ -662,4 +662,4 @@ static int identify(volatile uchar *p) return 0; /* don't know */ } -#endif /* CONFIG_IDE_TI_CARDBUS */ +#endif /* CONFIG_CMD_PCMCIA */ diff --git a/drivers/serial/serial_pl010.c b/drivers/serial/serial_pl010.c index 417b6aeda6..134ed0967f 100644 --- a/drivers/serial/serial_pl010.c +++ b/drivers/serial/serial_pl010.c @@ -29,6 +29,7 @@ /* Should be fairly simple to make it work with the PL010 as well */ #include <common.h> +#include <watchdog.h> #ifdef CFG_PL010_SERIAL @@ -137,7 +138,8 @@ void serial_setbrg (void) static void pl010_putc (int portnum, char c) { /* Wait until there is space in the FIFO */ - while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF); + while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF) + WATCHDOG_RESET(); /* Send the character */ IO_WRITE (port[portnum] + UART_PL01x_DR, c); @@ -148,7 +150,8 @@ static int pl010_getc (int portnum) unsigned int data; /* Wait until there is data in the FIFO */ - while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE); + while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE) + WATCHDOG_RESET(); data = IO_READ (port[portnum] + UART_PL01x_DR); @@ -164,6 +167,7 @@ static int pl010_getc (int portnum) static int pl010_tstc (int portnum) { + WATCHDOG_RESET(); return !(IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE); } diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index e66e0ee092..4f7b679eeb 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)libspi.a -COBJS-y += mpc8xxx_spi.o +COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o diff --git a/drivers/spi/mpc8xxx_spi.c b/drivers/spi/mpc8xxx_spi.c index 136fb50052..9eaf9860b4 100644 --- a/drivers/spi/mpc8xxx_spi.c +++ b/drivers/spi/mpc8xxx_spi.c @@ -22,7 +22,6 @@ */ #include <common.h> -#if defined(CONFIG_MPC8XXX_SPI) && defined(CONFIG_HARD_SPI) #include <malloc.h> #include <spi.h> @@ -180,4 +179,3 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, return 0; } -#endif /* CONFIG_HARD_SPI */ |