diff options
Diffstat (limited to 'include/configs/BC3450.h')
| -rw-r--r-- | include/configs/BC3450.h | 541 |
1 files changed, 0 insertions, 541 deletions
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h deleted file mode 100644 index 802e9cce1f..0000000000 --- a/include/configs/BC3450.h +++ /dev/null @@ -1,541 +0,0 @@ -/* - * -- Version 1.1 -- - * - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * (C) Copyright 2005 - * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de. - * - * History: - * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */ - -#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ -#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ -#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ -#define CONFIG_BC3450_USB 1 /* + USB support */ -# define CONFIG_FAT 1 /* + FAT support */ -# define CONFIG_EXT2 1 /* + EXT2 support */ -#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */ -#undef CONFIG_BC3450_CAN /* + CAN transceiver */ -#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */ -#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ -#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ -#define CONFIG_BC3450_FP 1 /* + enable FP O/P */ -#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFC000000 boot low (standard configuration with room for - * max 64 MByte Flash ROM) - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * AT-PS/2 Multiplexer - */ -#ifdef CONFIG_BC3450_PS2 -# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ -# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ -# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */ -# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ -# define CONFIG_BOARD_EARLY_INIT_R -#endif /* CONFIG_BC3450_PS2 */ - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -# define CONFIG_PCI 1 -# define CONFIG_PCI_PNP 1 -/* #define CONFIG_PCI_SCAN_SHOW 1 */ -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */ -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 - -/* - * Video console - */ -# define CONFIG_VIDEO -# define CONFIG_VIDEO_SM501 -# define CONFIG_VIDEO_SM501_32BPP -# define CONFIG_CFB_CONSOLE -# define CONFIG_VIDEO_LOGO -# define CONFIG_VGA_AS_SINGLE_DEVICE -# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */ -# define CONFIG_VIDEO_SW_CURSOR -# define CONFIG_SPLASH_SCREEN -# define CONFIG_SYS_CONSOLE_IS_IN_ENV - -/* - * Partitions - */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* - * USB - */ -#ifdef CONFIG_BC3450_USB -# define CONFIG_USB_OHCI -# define CONFIG_USB_STORAGE -#endif /* CONFIG_BC3450_USB */ - -/* - * POST support - */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif /* CONFIG_POST */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_BSP - -#ifdef CONFIG_VIDEO - #define CONFIG_CMD_BMP -#endif - -#ifdef CONFIG_BC3450_IDE - #define CONFIG_CMD_IDE -#endif - -#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB) - #ifdef CONFIG_FAT - #define CONFIG_CMD_FAT - #endif - - #ifdef CONFIG_EXT2 - #define CONFIG_CMD_EXT2 - #endif -#endif - -#ifdef CONFIG_BC3450_USB - #define CONFIG_CMD_USB -#endif - -#ifdef CONFIG_PCI - #define CONFIG_CMD_PCI -#endif - -#ifdef CONFIG_POST - #define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo;" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "ipaddr=192.168.1.10\0" \ - "serverip=192.168.1.3\0" \ - "netmask=255.255.255.0\0" \ - "hostname=bc3450\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "kernel_addr=fc0a0000\0" \ - "ramdisk_addr=fc1c0000\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "addcons=setenv bootargs $(bootargs) " \ - "console=ttyS0,$(baudrate) console=tty0\0" \ - "flash_self=run ramargs addip addcons;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile); " \ - "run nfsargs addip addcons; bootm\0" \ - "ide_nfs=run nfsargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ - "ide_ide=run ideargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ - "usb_self=run usbload; run ramargs addip addcons; " \ - "bootm 200000 400000\0" \ - "usbload=usb reset; usb scan; usbboot 200000 0:1; " \ - "usbboot 400000 0:2\0" \ - "bootfile=uImage\0" \ - "load=tftp 200000 $(u-boot)\0" \ - "u-boot=u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 $(filesize);" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for I²C EEPROM M24C32 - * M24C64 should work also. For other EEPROMs config should be verified. - * - * The TQM5200 module may hold an EEPROM at address 0x50. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231) -# define CONFIG_RTC_M41T11 1 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#else -# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */ -# define CONFIG_BOARD_EARLY_INIT_R -#endif - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* Dynamic MTD partition support */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=TQM5200-0" -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ - "1408k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif /*CONFIG_POST*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - * - * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#undef CONFIG_MPC5xxx_MII10 -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration on BC3450 - * - * PSC1: UART1 (Service-UART) [0x xxxxxxx4] - * PSC2: UART2 [0x xxxxxx4x] - * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] - * PSC3: USB2 [0x xxxxx1xx] - * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] - * (this has to match - * CONFIG_USB_CONFIG which is - * used by usb_ohci.c to set - * the USB ports) - * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] - * (this is reset to '5' - * in FEC driver: fec.c) - * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] - * ATA/CS: ??? [0x x1xxxxxx] - * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] - * CS1: Use Pin gpio_wkup_6 as second - * SDRAM chip select (mem_cs1) - * Timer: CAN2 / SPI - * I2C: CAN1 / I²C2 [0x bxxxxxxx] - */ -#ifdef CONFIG_BC3450_AC97 -# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124 -#else /* PSC2=UART2 */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144 -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max no of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */ - -#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */ - /* more extensive mem test */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* automatic configuration of chip selects */ -#ifdef CONFIG_TQM5200 -# define CONFIG_LAST_STAGE_INIT -#endif /* CONFIG_TQM5200 */ - -/* - * SRAM - Do not map below 2 GB in address space, because this area is used - * for SDRAM autosizing. - */ -#ifdef CONFIG_TQM5200 -# define CONFIG_SYS_CS2_START 0xE5000000 -# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */ -# define CONFIG_SYS_CS2_CFG 0x0004D930 -#endif /* CONFIG_TQM5200 */ - -/* - * Grafic controller - Do not map below 2 GB in address space, because this - * area is used for SDRAM autosizing. - */ -#ifdef CONFIG_TQM5200 -# define SM501_FB_BASE 0xE0000000 -# define CONFIG_SYS_CS1_START (SM501_FB_BASE) -# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ -# define CONFIG_SYS_CS1_CFG 0x8F48FF70 -# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 -#endif /* CONFIG_TQM5200 */ - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */ - /* flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * USB stuff - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ - -/* - * IDE/ATA stuff Supports IDE harddisk - */ -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ |