diff options
Diffstat (limited to 'include/configs/CPCI405.h')
| -rw-r--r-- | include/configs/CPCI405.h | 87 |
1 files changed, 41 insertions, 46 deletions
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 7c600d92ed..b159182eb5 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -44,30 +44,17 @@ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#if 0 -#define CONFIG_PREBOOT \ - "crc32 f0207004 ffc 0;" \ - "if cmp 0 f0207000 1;" \ - "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \ - "else;echo Old CRC is bad;fi" -#endif - #undef CONFIG_BOOTARGS -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ - "bootm ffc00000 ffca0000" -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ - "bootm ffc00000" -#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ #define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ CONFIG_BOOTP_DNS | \ @@ -79,6 +66,7 @@ CFG_CMD_PCI | \ CFG_CMD_IRQ | \ CFG_CMD_IDE | \ + CFG_CMD_FAT | \ CFG_CMD_ELF | \ CFG_CMD_MII | \ CFG_CMD_EEPROM ) @@ -86,6 +74,8 @@ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_VFAT + /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -134,35 +124,39 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_LOOPW 1 /* enable loopw command */ + #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ -#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ -#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + +#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ + +#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ +#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * IDE/ATA stuff @@ -221,23 +215,24 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ + #if 1 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- * NVRAM organization */ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ -#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ -#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ #define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ -#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */ #else /* Use EEPROM for environment variables */ -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x200 /* 512 bytes may be used for env vars */ +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */ /* total size of a CAT24WC08 is 1024 bytes */ #endif |