diff options
Diffstat (limited to 'include/configs/EP1C20.h')
| -rw-r--r-- | include/configs/EP1C20.h | 199 |
1 files changed, 199 insertions, 0 deletions
diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h new file mode 100644 index 0000000000..5507f352b9 --- /dev/null +++ b/include/configs/EP1C20.h @@ -0,0 +1,199 @@ +/* + * (C) Copyright 2005, Psyent Corporation <www.psyent.com> + * Scott McNutt <smcnutt@psyent.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*------------------------------------------------------------------------ + * BOARD/CPU + *----------------------------------------------------------------------*/ +#define CONFIG_EP1C20 1 /* EP1C20 board */ +#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ + +#define CFG_RESET_ADDR 0x00000000 /* Hard-reset address */ +#define CFG_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ +#define CFG_NIOS_SYSID_BASE 0x021208b8 /* System id address */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ + +/*------------------------------------------------------------------------ + * CACHE -- the following will support II/s and II/f. The II/s does not + * have dcache, so the cache instructions will behave as NOPs. + *----------------------------------------------------------------------*/ +#define CFG_ICACHE_SIZE 4096 /* 4 KByte total */ +#define CFG_ICACHELINE_SIZE 32 /* 32 bytes/line */ +#define CFG_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ +#define CFG_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ + +/*------------------------------------------------------------------------ + * MEMORY BASE ADDRESSES + *----------------------------------------------------------------------*/ +#define CFG_FLASH_BASE 0x00000000 /* FLASH base addr */ +#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */ +#define CFG_SDRAM_BASE 0x01000000 /* SDRAM base addr */ +#define CFG_SDRAM_SIZE 0x01000000 /* 16 MByte */ +#define CFG_SRAM_BASE 0x02000000 /* SRAM base addr */ +#define CFG_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ + +/*------------------------------------------------------------------------ + * MEMORY ORGANIZATION + * -Monitor at top. + * -The heap is placed below the monitor. + * -Global data is placed below the heap. + * -The stack is placed below global data (&grows down). + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 128k */ +#define CFG_GBL_DATA_SIZE 128 /* Global data size rsvd*/ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) + +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) +#define CFG_GBL_DATA_OFFSET (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP CFG_GBL_DATA_OFFSET + +/*------------------------------------------------------------------------ + * FLASH (AM29LV065D) + *----------------------------------------------------------------------*/ +#define CFG_MAX_FLASH_SECT 128 /* Max # sects per bank */ +#define CFG_MAX_FLASH_BANKS 1 /* Max # of flash banks */ +#define CFG_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ +#define CFG_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ +#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size */ + +/*------------------------------------------------------------------------ + * ENVIRONMENT -- Put environment in sector CFG_MONITOR_LEN above + * CFG_RESET_ADDR, since we assume the monitor is stored at the + * reset address, no? This will keep the environment in user region + * of flash. NOTE: the monitor length must be multiple of sector size + * (which is common practice). + *----------------------------------------------------------------------*/ +#define CFG_ENV_IS_IN_FLASH 1 /* Environment in flash */ +#define CFG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ +#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ +#define CFG_ENV_ADDR (CFG_RESET_ADDR + CFG_MONITOR_LEN) + +/*------------------------------------------------------------------------ + * CONSOLE + *----------------------------------------------------------------------*/ +#if defined(CONFIG_CONSOLE_JTAG) +#define CFG_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ +#else +#define CFG_NIOS_CONSOLE 0x02120840 /* UART base addr */ +#endif + +#define CFG_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ +#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ +#define CFG_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ + +#define CFG_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ + +/*------------------------------------------------------------------------ + * EPCS Device -- wne CFG_NIOS_EPCSBASE is defined code/commands for + * epcs device access is enabled. The base address is the epcs + * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. + * The register base is currently at offset 0x600 from the memory base. + *----------------------------------------------------------------------*/ +#define CFG_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ + +/*------------------------------------------------------------------------ + * DEBUG + *----------------------------------------------------------------------*/ +#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ + +/*------------------------------------------------------------------------ + * TIMEBASE -- + * + * The high res timer defaults to 1 msec. Since it includes the period + * registers, we can slow it down to 10 msec using TMRCNT. If the default + * period is acceptable, TMRCNT can be left undefined. + *----------------------------------------------------------------------*/ +#define CFG_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ +#define CFG_NIOS_TMRIRQ 3 /* Timer IRQ num */ +#define CFG_NIOS_TMRMS 10 /* 10 msec per tick */ +#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) +#define CFG_HZ (CONFIG_SYS_CLK_FREQ/(CFG_NIOS_TMRCNT + 1)) + +/*------------------------------------------------------------------------ + * STATUS LED -- Provides a simple blinking led. For Nios2 each board + * must implement its own led routines -- leds are, after all, + * board-specific, no? + *----------------------------------------------------------------------*/ +#define CFG_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ +#define CONFIG_STATUS_LED /* Enable status driver */ + +#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ +#define STATUS_LED_STATE 1 /* Blinking */ +#define STATUS_LED_PERIOD (500/CFG_NIOS_TMRMS) /* Every 500 msec */ + +/*------------------------------------------------------------------------ + * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... + * and really doesn't need any additional clutter. So I choose the lazy + * way out to avoid changes there -- define the base address to ensure + * cache bypass so there's no need to monkey with inx/outx macros. + *----------------------------------------------------------------------*/ +#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ +#define CONFIG_DRIVER_SMC91111 /* Using SMC91c111 */ +#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ +#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ + +#define CONFIG_ETHADDR 08:00:3e:26:0a:5b +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.2.21 +#define CONFIG_SERVERIP 192.168.2.16 + +/*------------------------------------------------------------------------ + * COMMANDS + *----------------------------------------------------------------------*/ +#define CONFIG_COMMANDS (CFG_CMD_BDI | \ + CFG_CMD_DHCP | \ + CFG_CMD_ECHO | \ + CFG_CMD_ENV | \ + CFG_CMD_FLASH | \ + CFG_CMD_IMI | \ + CFG_CMD_IRQ | \ + CFG_CMD_LOADS | \ + CFG_CMD_LOADB | \ + CFG_CMD_MEMORY | \ + CFG_CMD_MISC | \ + CFG_CMD_NET | \ + CFG_CMD_PING | \ + CFG_CMD_RUN | \ + CFG_CMD_SAVES ) +#include <cmd_confdefs.h> + +/*------------------------------------------------------------------------ + * MISC + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* Provide extended help*/ +#define CFG_PROMPT "==> " /* Command prompt */ +#define CFG_CBSIZE 256 /* Console I/O buf size */ +#define CFG_MAXARGS 16 /* Max command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot arg buf size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buf size */ +#define CFG_LOAD_ADDR CFG_SDRAM_BASE /* Default load address */ +#define CFG_MEMTEST_START CFG_SDRAM_BASE /* Start addr for test */ +#define CFG_MEMTEST_END CFG_INIT_SP - 0x00020000 + +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " + +#endif /* __CONFIG_H */ |