diff options
Diffstat (limited to 'include/configs/ICU862.h')
-rw-r--r-- | include/configs/ICU862.h | 443 |
1 files changed, 0 insertions, 443 deletions
diff --git a/include/configs/ICU862.h b/include/configs/ICU862.h deleted file mode 100644 index 16af4bbcad..0000000000 --- a/include/configs/ICU862.h +++ /dev/null @@ -1,443 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <mpc8xx_irq.h> - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC860 1 -#define CONFIG_MPC860T 1 -#define CONFIG_ICU862 1 -#define CONFIG_MPC862 1 - -#define CONFIG_SYS_TEXT_BASE 0x40F00000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ - -#ifdef CONFIG_100MHz -#define MPC8XX_FACT 24 /* Multiply by 24 */ -#define MPC8XX_XIN 4165000 /* 4.165 MHz in */ -#define CONFIG_8xx_GCLK_FREQ (MPC8XX_FACT * MPC8XX_XIN) - /* define if cant' use get_gclk_freq */ -#else -#if 1 /* for 50MHz version of processor */ -#define MPC8XX_FACT 12 /* Multiply by 12 */ -#define MPC8XX_XIN 4000000 /* 4 MHz in */ -#define CONFIG_8xx_GCLK_FREQ 48000000 /* define if cant use get_gclk_freq */ -#else /* for 80MHz version of processor */ -#define MPC8XX_FACT 20 /* Multiply by 20 */ -#define MPC8XX_XIN 4000000 /* 4 MHz in */ -#define CONFIG_8xx_GCLK_FREQ 80000000 /* define if cant use get_gclk_freq */ -#endif -#endif - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */ -#define CONFIG_FEC_ENET 1 /* use FEC ethernet */ -#define CONFIG_MII 1 -#if 1 -#define CONFIG_SYS_DISCOVER_PHY 1 -#else -#undef CONFIG_SYS_DISCOVER_PHY -#endif - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/* - * Software (bit-bang) I2C driver configuration - */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#define CONFIG_SYS_EEPROM_X40430 /* Use a Xicor X40430 EEPROM */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16 bytes page write mode */ - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0000000 -#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#define CONFIG_SYS_FLASH_SIZE ((uint)(16 * 1024 * 1024)) /* max 16Mbyte */ - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -#if 0 -#if defined(DEBUG) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#endif -#else -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00F40000 - -#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * set the PLL, the low-power modes and the reset control (15-29) - */ -#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#ifdef CONFIG_100MHz /* for 100 MHz, external bus is half CPU clock */ -#define SCCR_MASK 0 -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ - SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ - SCCR_DFLCD000 |SCCR_DFALCD00 | SCCR_EBDF01) -#else /* up to 50 MHz we use a 1:1 clock */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ - SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ - SCCR_DFLCD000 |SCCR_DFALCD00 ) -#endif /* CONFIG_100MHz */ - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration Register 19-4 - *----------------------------------------------------------------------- - */ -/* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */ -#define CONFIG_SYS_RCCR 0x0020 - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * PCMCIA Power Switch - * - * The ICU862 uses a TPS2205 PC-Card Power-Interface Switch to - * control the voltages on the PCMCIA slot which is connected to Port B - *----------------------------------------------------------------------- - */ - /* Output pins */ -#define TPS2205_VCC5 0x00008000 /* PB.16: 5V Voltage Control */ -#define TPS2205_VCC3 0x00004000 /* PB.17: 3V Voltage Control */ -#define TPS2205_VPP_PGM 0x00002000 /* PB.18: PGM Voltage Control */ -#define TPS2205_VPP_VCC 0x00001000 /* PB.19: VPP Voltage Control */ -#define TPS2205_SHDN 0x00000200 /* PB.22: Shutdown */ -#define TPS2205_OUTPUTS ( TPS2205_VCC5 | TPS2205_VCC3 | \ - TPS2205_VPP_PGM | TPS2205_VPP_VCC | \ - TPS2205_SHDN) - - /* Input pins */ -#define TPS2205_OC 0x00000100 /* PB.23: Over-Current */ -#define TPS2205_INPUTS ( TPS2205_OC ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - - - /*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the -* entire address space, we have to set the memory controller -* differently. Normally, you write the option register -* first, and then enable the chip select by writing the -* base register. For CS0, you must write the base register -* first, followed by the option register. -*/ - -/* - * Init Memory Controller: - * - * BR0 and OR0 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x0 /* FLASH bank #1 */ - -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) - -#define CONFIG_SYS_OR0_PRELIM 0xFF000954 /* Real values for the board */ -#define CONFIG_SYS_BR0_PRELIM 0x40000001 /* Real values for the board */ - -/* - * BR1 and OR1 (SDRAM) - */ -#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank */ -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ - -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000800 /* BIH is not set */ - -#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM) -#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V) - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#define CONFIG_SYS_MAMR 0x13a01114 - -#ifdef CONFIG_MPC860T - -/* Interrupt level assignments. -*/ -#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ - -#endif /* CONFIG_MPC860T */ - - -#endif /* __CONFIG_H */ |