diff options
Diffstat (limited to 'include/configs/MPC8323ERDB.h')
| -rw-r--r-- | include/configs/MPC8323ERDB.h | 583 |
1 files changed, 583 insertions, 0 deletions
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h new file mode 100644 index 0000000000..376973b94d --- /dev/null +++ b/include/configs/MPC8323ERDB.h @@ -0,0 +1,583 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ +#define CONFIG_MPC83XX 1 /* MPC83xx family */ +#define CONFIG_MPC832X 1 /* MPC832x CPU specific */ + +#define CONFIG_PCI 1 +#define CONFIG_83XX_GENERIC_PCI 1 + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 66666667 /* in Hz */ + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN +#endif + +/* + * Hardware Reset Configuration Word + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_VCO_1X2 |\ + HRCWL_CSB_TO_CLKIN_2X1 |\ + HRCWL_CORE_TO_CSB_2_5X1 |\ + HRCWL_CE_PLL_VCO_DIV_2 |\ + HRCWL_CE_PLL_DIV_1X1 |\ + HRCWL_CE_TO_PLL_1X3) + +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_NORMAL) + +/* + * System IO Config + */ +#define CFG_SICRL 0x00000000 + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ + +#undef CONFIG_SPD_EEPROM +#if defined(CONFIG_SPD_EEPROM) +/* Determine DDR configuration from I2C interface + */ +#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ +#else +/* Manually set up DDR parameters + */ +#define CFG_DDR_SIZE 64 /* MB */ +#define CFG_DDR_CS0_CONFIG 0x80840101 +#define CFG_DDR_TIMING_0 0x00220802 +#define CFG_DDR_TIMING_1 0x3935d322 +#define CFG_DDR_TIMING_2 0x0f9048ca +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_CLK_CNTL 0x02000000 +#define CFG_DDR_MODE 0x44400232 +#define CFG_DDR_MODE2 0x8000c000 +#define CFG_DDR_INTERVAL 0x03200064 +#define CFG_DDR_CS0_BNDS 0x00000003 +#define CFG_DDR_SDRAM_CFG 0x43080000 +#define CFG_DDR_SDRAM_CFG2 0x00401000 +#endif + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00030000 /* memtest region */ +#define CFG_MEMTEST_END 0x03f00000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) +#define CFG_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM + +/* + * SDRAM on the Local Bus + */ +#undef CFG_LB_SDRAM /* The board has not SRDAM on local bus */ + +#ifdef CFG_LB_SDRAM +#define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +#define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE +#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ + +/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 + * + * CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * the top 17 bits of BR2. + */ + +#define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 + */ + +#define CFG_OR2_PRELIM 0xfc006901 + +#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +#define CFG_LBC_LSDMR_COMMON 0x0063b723 + +/* + * SDRAM Controller configuration sequence. + */ +#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_PCHALL) +#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_MRW) +#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_NORMAL) + +#endif + +/* + * Windows to access PIB via local bus + */ +#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ +#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,8323@0" +#define OF_SOC "soc8323@e0000000" +#define OF_QE "qe@e0100000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc8323@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_MMIO_BASE 0x90000000 +#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE +#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_IO_BASE 0xd0000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x04000000 /* 64M */ + +#ifdef CONFIG_PCI + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "Freescale GETH" + +#define CONFIG_UEC_ETH1 /* ETH3 */ + +#ifdef CONFIG_UEC_ETH1 +#define CFG_UEC1_UCC_NUM 2 /* UCC3 */ +#define CFG_UEC1_RX_CLK QE_CLK9 +#define CFG_UEC1_TX_CLK QE_CLK10 +#define CFG_UEC1_ETH_TYPE FAST_ETH +#define CFG_UEC1_PHY_ADDR 4 +#define CFG_UEC1_INTERFACE_MODE ENET_100_MII +#endif + +#define CONFIG_UEC_ETH2 /* ETH4 */ + +#ifdef CONFIG_UEC_ETH2 +#define CFG_UEC2_UCC_NUM 1 /* UCC2 */ +#define CFG_UEC2_RX_CLK QE_CLK16 +#define CFG_UEC2_TX_CLK QE_CLK3 +#define CFG_UEC2_ETH_TYPE FAST_ETH +#define CFG_UEC2_PHY_ADDR 0 +#define CFG_UEC2_INTERFACE_MODE ENET_100_MII +#endif + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_ASKENV + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif +#if defined(CFG_RAMBOOT) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Cache Config + */ +#define CFG_DCACHE_SIZE 16384 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +/* IMMRBAR & PCI IO: cache-inhibit and guarded */ +#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT2U CFG_IBAT2U + +#define CFG_IBAT3L (0) +#define CFG_IBAT3U (0) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT4L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT4U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT5L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT5U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT6L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT6U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#else +#define CFG_IBAT5L (0) +#define CFG_IBAT5U (0) +#define CFG_IBAT6L (0) +#define CFG_IBAT6U (0) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#endif + +/* Nothing in BAT7 */ +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ETHADDR 00:04:9f:ef:03:01 +#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */ +#define CONFIG_ETH1ADDR 00:04:9f:ef:03:02 + +#define CONFIG_IPADDR 10.0.0.2 +#define CONFIG_SERVERIP 10.0.0.1 +#define CONFIG_GATEWAYIP 10.0.0.1 +#define CONFIG_NETMASK 255.0.0.0 +#define CONFIG_NETDEV eth1 + +#define CONFIG_HOSTNAME mpc8323erdb +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_RAMDISKFILE rootfs.ext2.gz.uboot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ +#define CONFIG_FDTFILE mpc832x_rdb.dtb + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ +#define CONFIG_BAUDRATE 115200 + +#define XMK_STR(x) #x +#define MK_STR(x) XMK_STR(x) + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" MK_STR(CONFIG_NETDEV) "\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftp $loadaddr $uboot;" \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "fdtaddr=400000\0" \ + "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \ + "console=ttyS0\0" \ + "setbootargs=setenv bootargs " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ + "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setbootargs;" \ + "run setipargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv rootdev /dev/ram;" \ + "run setbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#undef MK_STR +#undef XMK_STR + +#endif /* __CONFIG_H */ |