diff options
Diffstat (limited to 'include/configs/MPC8349EMDS_SDRAM.h')
| -rw-r--r-- | include/configs/MPC8349EMDS_SDRAM.h | 731 |
1 files changed, 731 insertions, 0 deletions
diff --git a/include/configs/MPC8349EMDS_SDRAM.h b/include/configs/MPC8349EMDS_SDRAM.h new file mode 100644 index 0000000000..b610b555a7 --- /dev/null +++ b/include/configs/MPC8349EMDS_SDRAM.h @@ -0,0 +1,731 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2006-2010 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + */ + +/* + * mpc8349emds board configuration file + * + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ + +#define CONFIG_PCI_66M +#ifdef CONFIG_PCI_66M +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#else +#define CONFIG_83XX_CLKIN 33000000 /* in Hz */ +#endif + +#ifdef CONFIG_PCISLAVE +#define CONFIG_83XX_PCICLK 66666666 /* in Hz */ +#endif /* CONFIG_PCISLAVE */ + +#ifndef CONFIG_SYS_CLK_FREQ +#ifdef CONFIG_PCI_66M +#define CONFIG_SYS_CLK_FREQ 66000000 +#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 +#else +#define CONFIG_SYS_CLK_FREQ 33000000 +#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 +#endif +#endif + +#define CONFIG_SYS_IMMR 0xE0000000 + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00100000 + +/* + * DDR Setup + */ +#define CONFIG_DDR_ECC /* support DDR ECC function */ +#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ +#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ + +/* + * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver + * unselect it to use old spd_sdram.c + */ +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS1 0x52 +#define SPD_EEPROM_ADDRESS2 0x51 +#define CONFIG_DIMM_SLOTS_PER_CTLR 2 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +/* + * 32-bit data path mode. + * + * Please note that using this mode for devices with the real density of 64-bit + * effectively reduces the amount of available memory due to the effect of + * wrapping around while translating address to row/columns, for example in the + * 256MB module the upper 128MB get aliased with contents of the lower + * 128MB); normally this define should be used for devices with real 32-bit + * data path. + */ +#undef CONFIG_DDR_32BIT + +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ + | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#undef CONFIG_DDR_2T_TIMING + +/* + * DDRCDR - DDR Control Driver Register + */ +#define CONFIG_SYS_DDRCDR_VALUE 0x80080001 + +#if defined(CONFIG_SPD_EEPROM) +/* + * Determine DDR configuration from I2C interface. + */ +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ +#else +/* + * Manually set up DDR parameters + */ +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#if defined(CONFIG_DDR_II) +#define CONFIG_SYS_DDRCDR 0x80080001 +#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102 +#define CONFIG_SYS_DDR_TIMING_0 0x00220802 +#define CONFIG_SYS_DDR_TIMING_1 0x38357322 +#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 +#define CONFIG_SYS_DDR_MODE 0x47d00432 +#define CONFIG_SYS_DDR_MODE2 0x8000c000 +#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 +#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#else +#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) +#define CONFIG_SYS_DDR_TIMING_1 0x36332321 +#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ +#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ +#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ + +#if defined(CONFIG_DDR_32BIT) +/* set burst length to 8 for 32-bit data path */ + /* DLL,normal,seq,4/2.5, 8 burst len */ +#define CONFIG_SYS_DDR_MODE 0x00000023 +#else +/* the default burst length is 4 - for 64-bit data path */ + /* DLL,normal,seq,4/2.5, 4 burst len */ +#define CONFIG_SYS_DDR_MODE 0x00000022 +#endif +#endif +#endif + +/* + * SDRAM on the Local Bus + */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */ + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET \ + | OR_GPCM_EAD) + + /* window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +/* + * BCSR register on local bus 32KB, 8-bit wide for MDS config reg + */ +#define CONFIG_SYS_BCSR 0xE2400000 + /* Access window base at BCSR base */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ + | BR_PS_8 \ + | BR_MS_GPCM \ + | BR_V) + /* 0x00000801 */ +#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ + | OR_GPCM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_CLEAR \ + | OR_GPCM_EHTR_CLEAR) + /* 0xFFFFE8F0 */ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ + +/* + * Local Bus LCRR and LBCR regs + * LCRR: DLL bypass, Clock divider is 4 + * External Local Bus rate is + * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory. + */ + +/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */ +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port-size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 + */ + +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \ + | BR_PS_32 /* 32-bit port */ \ + | BR_MS_SDRAM /* MSEL = SDRAM */ \ + | BR_V) /* Valid */ + /* 0xF0001861 */ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) + +/* + * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 + */ + +#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \ + | OR_SDRAM_XAM \ + | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \ + | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \ + | OR_SDRAM_EAD) + /* 0xFC006901 */ + + /* LB sdram refresh timer, about 6us */ +#define CONFIG_SYS_LBC_LSRT 0x32000000 + /* LB refresh timer prescal, 266MHz/32 */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 + +#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ + | LSDMR_BSMA1516 \ + | LSDMR_RFCR8 \ + | LSDMR_PRETOACT6 \ + | LSDMR_ACTTORW3 \ + | LSDMR_BL8 \ + | LSDMR_WRC3 \ + | LSDMR_CL3) + +/* + * SDRAM Controller configuration sequence. + */ +#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) +#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) +#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) +#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) +#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } + +/* SPI */ +#undef CONFIG_SOFT_SPI /* SPI bit-banged */ + +/* GPIOs. Used as SPI chip selects */ +#define CONFIG_SYS_GPIO1_PRELIM +#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */ +#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */ + +/* TSEC */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) + +/* USB */ +#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE +#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 +#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE +#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 +#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ + +#if defined(CONFIG_PCI) + +#define PCI_ONE_PCI1 +#if defined(PCI_64BIT) +#undef PCI_ALL_PCI1 +#undef PCI_TWO_PCI1 +#undef PCI_ONE_PCI1 +#endif + +#define CONFIG_83XX_PCI_STREAMING + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xFIXME + #define PCI_ENET0_MEMADDR 0xFIXME + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + +/* + * TSEC configuration + */ + +#if defined(CONFIG_TSEC_ENET) + +#define CONFIG_GMII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Configure on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * Environment + */ +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_ADDR \ + (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) + #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CONFIG_ENV_SIZE 0x2000 + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#else + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * Command line configuration. + */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ + /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ + +#if 1 /*528/264*/ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X2 |\ + HRCWL_CORE_TO_CSB_2X1) +#elif 0 /*396/132*/ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_3X1) +#elif 0 /*264/132*/ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_2X1) +#elif 0 /*132/132*/ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_1X1) +#elif 0 /*264/264 */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_1X1) +#endif + +#ifdef CONFIG_PCISLAVE +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_AGENT |\ + HRCWH_64_BIT_PCI |\ + HRCWH_PCI1_ARBITER_DISABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII) +#else +#if defined(PCI_64BIT) +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_64_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII) +#else +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_32_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII) +#endif /* PCI_64BIT */ +#endif /* CONFIG_PCISLAVE */ + +/* + * System performance + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ +#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ +#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ +#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ + +/* System IO Config */ +#define CONFIG_SYS_SICRH 0 +#define CONFIG_SYS_SICRL SICRL_LDP_A + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ + | HID0_ENABLE_INSTRUCTION_CACHE) + +/* #define CONFIG_SYS_HID0_FINAL (\ + HID0_ENABLE_INSTRUCTION_CACHE |\ + HID0_ENABLE_M_BIT |\ + HID0_ENABLE_ADDRESS_BROADCAST) */ + +#define CONFIG_SYS_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR @ 0x00000000 */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +/* PCI @ 0x80000000 */ +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#else +#define CONFIG_SYS_IBAT1L (0) +#define CONFIG_SYS_IBAT1U (0) +#define CONFIG_SYS_IBAT2L (0) +#define CONFIG_SYS_IBAT2U (0) +#endif + +#ifdef CONFIG_MPC83XX_PCI2 +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#else +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) +#endif + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ +#define CONFIG_SYS_IBAT6L (0xF0000000 \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6U (0xF0000000 \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH0 +#endif + +#define CONFIG_HOSTNAME "mpc8349emds" +#define CONFIG_ROOTPATH "/nfsroot/rootfs" +#define CONFIG_BOOTFILE "uImage" + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=mpc8349emds\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \ + "update=protect off fe000000 fe03ffff; " \ + "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\ + "upd=run load update\0" \ + "fdtaddr=780000\0" \ + "fdtfile=mpc834x_mds.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ + "$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#endif /* __CONFIG_H */ |