diff options
Diffstat (limited to 'include/configs/PIP405.h')
| -rw-r--r-- | include/configs/PIP405.h | 157 |
1 files changed, 78 insertions, 79 deletions
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index 2ceda001ca..5c4d69b207 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -79,8 +79,8 @@ #define CONFIG_NAND_LEGACY -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /************************************************************** * I2C Stuff: * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address @@ -90,21 +90,20 @@ * The Atmel EEPROM uses 16Bit addressing. ***************************************************************/ #define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CFG_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CFG_I2C_EEPROM_ADDR 0x53 -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */ -#undef CFG_I2C_EEPROM_ADDR_OVERFLOW -#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */ +#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */ /* 64 byte page write mode using*/ /* last 6 bits of the address */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE /* enable Page write */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ /*************************************************************** @@ -135,54 +134,54 @@ /*************************************************************** * defines if the console is stored in the environment ***************************************************************/ -#define CFG_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */ /*************************************************************** * defines if an overwrite_console function exists *************************************************************/ -#define CFG_CONSOLE_OVERWRITE_ROUTINE -#define CFG_CONSOLE_INFO_QUIET +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#define CONFIG_SYS_CONSOLE_INFO_QUIET /*************************************************************** * defines if the overwrite_console should be stored in the * environment **************************************************************/ -#undef CFG_CONSOLE_ENV_OVERWRITE +#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE /************************************************************** * loads config *************************************************************/ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MISC_INIT_R /*********************************************************** * Miscellaneous configurable options **********************************************************/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_BASE_BAUD 691200 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } -#define CFG_LOAD_ADDR 0x400000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff @@ -196,40 +195,40 @@ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */ #define CONFIG_PCI_PNP /* pci plug-and-play */ /* resource configuration */ -#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFF80000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* * Init Memory Controller: @@ -249,14 +248,14 @@ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in On Chip SRAM) */ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR 0xF0000000 -#define CFG_OCM_DATA_SIZE 0x1000 -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of On Chip SRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Internal Definitions @@ -270,7 +269,7 @@ /*********************************************************************** * External peripheral base address ***********************************************************************/ -#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000 +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000 /*********************************************************************** * Last Stage Init @@ -279,9 +278,9 @@ /************************************************************ * Ethernet Stuff ***********************************************************/ +#define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ -#define CONFIG_CS8952_PHY 1 /* its a CS8952 PHY */ /************************************************************ * RTC ***********************************************************/ @@ -291,15 +290,15 @@ /************************************************************ * IDE/ATA stuff ************************************************************/ -#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */ -#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ -#define CFG_ATA_BASE_ADDR CFG_ISA_IO_BASE_ADDRESS /* base address */ -#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ -#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ -#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */ -#define CFG_ATA_REG_OFFSET 0 /* reg offset */ -#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */ +#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */ +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ +#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ +#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ @@ -316,18 +315,18 @@ * SCSI support (experimental) only SYM53C8xx supported ************************************************************/ #define CONFIG_SCSI_SYM53C8XX -#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */ -#define CFG_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */ -#define CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */ -#define CFG_SCSI_SPIN_UP_TIME 2 +#define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */ +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */ +#define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */ +#define CONFIG_SYS_SCSI_SPIN_UP_TIME 2 /************************************************************ * Disk-On-Chip configuration ************************************************************/ -#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ -#define CFG_DOC_SHORT_TIMEOUT -#define CFG_DOC_SUPPORT_2000 -#define CFG_DOC_SUPPORT_MILLENNIUM +#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ +#define CONFIG_SYS_DOC_SHORT_TIMEOUT +#define CONFIG_SYS_DOC_SUPPORT_2000 +#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM /************************************************************ * DISK Partition support @@ -361,7 +360,7 @@ #define CONFIG_USB_STORAGE /* Enable needed helper functions */ -#define CFG_DEVICE_DEREGISTER /* needs device_deregister */ +#define CONFIG_SYS_DEVICE_DEREGISTER /* needs device_deregister */ /************************************************************ * Debug support |