diff options
Diffstat (limited to 'include/configs/PPChameleonEVB.h')
| -rw-r--r-- | include/configs/PPChameleonEVB.h | 149 |
1 files changed, 108 insertions, 41 deletions
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 0c9b6dd7e4..bb8ce43bab 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -38,6 +38,18 @@ #define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA #endif + +/* Only one of the following two symbols must be defined (default is 25 MHz) + * CONFIG_PPCHAMELEON_CLK_25 + * CONFIG_PPCHAMELEON_CLK_33 + */ + +#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) +#error "* Two external frequencies (SysClk) are defined! *" +#endif + +#undef CONFIG_PPCHAMELEON_SMI712 + /* * Debug stuff */ @@ -60,7 +72,14 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#ifdef CONFIG_PPCHAMELEON_CLK_25 + #define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ +#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#else +#error "* External frequency (SysClk) not defined! *" +#endif #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ @@ -75,7 +94,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - #undef CONFIG_EXT_PHY #define CONFIG_NET_MULTI 1 @@ -184,7 +202,6 @@ #define CFG_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ #define CFG_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ - #define NAND_DISABLE_CE(nand) do \ { \ switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \ @@ -211,7 +228,6 @@ } \ } while(0) - #define NAND_CTL_CLRALE(nandptr) do \ { \ switch((unsigned long)nandptr) \ @@ -292,9 +308,10 @@ #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ #define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ + #define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ #define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ @@ -349,12 +366,23 @@ /*----------------------------------------------------------------------- * Environment Variable setup */ +#ifdef ENVIRONMENT_IN_EEPROM + +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x700 /* 2048-256 bytes may be used for env vars (total size of a CAT24WC16 is 2048 bytes)*/ + +#else /* DEFAULT: environment in flash, using redundand flash sectors */ + #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CFG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ #define CFG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ #define CFG_ENV_ADDR_REDUND 0xFFFFA000 #define CFG_ENV_SIZE_REDUND 0x2000 +#endif /* ENVIRONMENT_IN_EEPROM */ + + #define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ #define CFG_NVRAM_SIZE 242 /* NVRAM size */ @@ -414,23 +442,21 @@ #define CFG_EBC_PB3AP 0x92015480 #define CFG_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#if 0 /* Roese */ -/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x92015480 -#define CFG_EBC_PB1CR 0xFF858000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (CAN0, 1) initialization */ -#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (CompactFlash IDE) initialization */ -#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ - -/* Memory Bank 4 (NVRAM/RTC) initialization */ -#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */ -#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ +#ifdef CONFIG_PPCHAMELEON_SMI712 +/* + * Video console (graphic: SMI LynxEM) + */ +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SMI_LYNXEM +#define CONFIG_VIDEO_LOGO +/*#define CONFIG_VIDEO_BMP_LOGO*/ +#define CONFIG_CONSOLE_EXTRA_INFO +#define CONFIG_VGA_AS_SINGLE_DEVICE +/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ +#define CFG_ISA_IO 0xE8000000 +/* see also drivers/videomodes.c */ +#define CFG_DEFAULT_VIDEO_MODE 0x303 #endif /*----------------------------------------------------------------------- @@ -485,6 +511,7 @@ #define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ #define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ + #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -525,7 +552,6 @@ /*--------------------------------------------------------------------*/ #ifdef CONFIG_NO_SERIAL_EEPROM - /* !----------------------------------------------------------------------- ! Defines for entry options. @@ -537,7 +563,6 @@ #define DIMM_READ_ADDR 0xAB #define DIMM_WRITE_ADDR 0xAA - #define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ #define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ #define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ @@ -649,50 +674,92 @@ #define PLL_PCIDIV_3 0x00000002 #define PLL_PCIDIV_4 0x00000003 + +#ifdef CONFIG_PPCHAMELEON_CLK_25 +/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ +#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_2) +#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) + +#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) + /* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ +#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ +#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + +#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ +#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + +#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ +#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + +#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ +#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) +#else +#error "* External frequency (SysClk) not defined! *" +#endif + #if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) /* Model HI */ -#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55 +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 +#define CFG_OPB_FREQ 55555555 /* Model ME */ #elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33 +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 +#define CFG_OPB_FREQ 66666666 #else /* Model BA (default) */ -#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33 - +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 +#define CFG_OPB_FREQ 66666666 #endif -#endif /* CONFIG_NO_SERIAL_EEPROM */ +#endif -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ +#define CONFIG_JFFS2_NAND 0 /* jffs2 on nand support */ #define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */ #define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */ #define CONFIG_JFFS2_NAND_SIZE 2*1024*1024 /* size of jffs2 partition */ |