diff options
Diffstat (limited to 'include/configs/TQM5200.h')
| -rw-r--r-- | include/configs/TQM5200.h | 101 |
1 files changed, 68 insertions, 33 deletions
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index e0de5c1b36..897d1b262b 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -285,7 +285,7 @@ */ #define CFG_IPBSPEED_133 /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200) /* * PCI Bus clocking configuration * @@ -349,13 +349,29 @@ */ #define CFG_FLASH_BASE 0xFC000000 +#ifndef CONFIG_CAM5200 /* use CFI flash driver */ #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ #define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#else /* CONFIG_CAM5200 */ +#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks + (= chip selects) */ +#define CFG_FLASH_WORD_SIZE unsigned int /* main flash device with */ +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_ADDR0 0x555 +#define CFG_FLASH_ADDR1 0x2AA +#define CFG_FLASH_2ND_16BIT_DEV 1 /* NIOS flash is a 16bit device */ +#define CFG_MAX_FLASH_SECT 128 +#endif /* ifndef CONFIG_CAM5200 */ + #define CFG_FLASH_EMPTY_INFO #define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ #define CFG_FLASH_USE_BUFFER_WRITE 1 #if defined (CONFIG_CAM5200) @@ -366,9 +382,6 @@ # define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) #endif -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ - /* Dynamic MTD partition support */ #define CONFIG_JFFS2_CMDLINE #define MTDIDS_DEFAULT "nor0=TQM5200-0" @@ -401,10 +414,8 @@ #elif defined (CONFIG_CAM5200) # define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \ "1792k(kernel)," \ - "3584k(small-fs)," \ - "2m(initrd)," \ - "8m(misc)," \ - "16m(big-fs)" + "5632k(rootfs)," \ + "24m(home)" #elif defined (CONFIG_FO300) # define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ "1408k(kernel)," \ @@ -479,31 +490,43 @@ /* * GPIO configuration * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 + * use CS1: Bit 0 (mask: 0x80000000): + * 1 -> Pin gpio_wkup_6 as second SDRAM chip select (mem_cs1). * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards and FO300 boards. Do not use - * with REV100 modules (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * 01x -> Use AC97 - * use PSC3: Bits 20-23 (mask: 0x00000f00) - * 1100 -> UART/SPI (on FO300 board) - * use PSC6: - * on STK52xx and FO300: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. + * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. + * SPI on PSC3 according to PSC3 setting. Use for CAM5200. + * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. + * Use for REV200 STK52XX boards and FO300 boards. Do not use + * with REV100 modules (because, there I2C1 is used as I2C bus). + * use ATA: Bits 6-7 (mask 0x03000000): + * 00 -> No ATA chip selects, csb_4/5 used as normal chip selects. + * Use for CAM5200 board. + * 01 -> ATA cs0/1 on csb_4/5. Use for the remaining boards. + * use PSC6: Bits 9-11 (mask 0x00700000): + * 000 -> use PSC6_0 to PSC6_3 as GPIO, PSC6 could not be used as + * UART, CODEC or IrDA. + * GPIO on PSC6_3 is used in post_hotkeys_pressed() to + * enable extended POST tests. + * Use for MINI-FAP and TQM5200_IB boards. + * 101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used. + * Extended POST test is not available. + * Use for STK52xx, FO300 and CAM5200 boards. + * use PCI_DIS: Bit 16 (mask 0x00008000): + * 1 -> disable PCI controller (on CAM5200 board). + * use USB: Bits 18-19 (mask 0x00003000): + * 10 -> two UARTs (on FO300 and CAM5200). + * use PSC3: Bits 20-23 (mask: 0x00000f00): + * 0000 -> All PSC3 pins are GPIOs. + * 1100 -> UART/SPI (on FO300 board). + * 0100 -> UART (on CAM5200 board). + * use PSC2: Bits 25:27 (mask: 0x00000030): + * 000 -> All PSC2 pins are GPIOs. + * 100 -> UART (on CAM5200 board). + * 001 -> CAN1/2 on PSC2 pins. + * Use for REV100 STK52xx boards + * 01x -> Use AC97 (on FO300 board). + * use PSC1: Bits 29-31 (mask: 0x00000007): + * 100 -> UART (on all boards). */ #if defined (CONFIG_MINIFAP) # define CFG_GPS_PORT_CONFIG 0x91000004 @@ -519,6 +542,8 @@ # endif #elif defined (CONFIG_FO300) # define CFG_GPS_PORT_CONFIG 0x91502c24 +#elif defined (CONFIG_CAM5200) +# define CFG_GPS_PORT_CONFIG 0x8050A444 #else /* TMQ5200 Inbetriebnahme-Board */ # define CFG_GPS_PORT_CONFIG 0x81000004 #endif @@ -613,6 +638,16 @@ #define CFG_CS_BURST 0x00000000 #define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ +#if defined(CONFIG_CAM5200) +#define CFG_CS4_START 0xB0000000 +#define CFG_CS4_SIZE 0x00010000 +#define CFG_CS4_CFG 0x01019C10 + +#define CFG_CS5_START 0xD0000000 +#define CFG_CS5_SIZE 0x01208000 +#define CFG_CS5_CFG 0x1414BF10 +#endif + #define CFG_RESET_ADDRESS 0xff000000 /*----------------------------------------------------------------------- |