diff options
Diffstat (limited to 'include/configs/V38B.h')
| -rw-r--r-- | include/configs/V38B.h | 368 |
1 files changed, 368 insertions, 0 deletions
diff --git a/include/configs/V38B.h b/include/configs/V38B.h new file mode 100644 index 0000000000..9b8fc699a9 --- /dev/null +++ b/include/configs/V38B.h @@ -0,0 +1,368 @@ +/* + * (C) Copyright 2003-2004 Wolfgang Denk, DENX Software Engineering, + * wd@denx.de. + * + * See file CREDITS for list of people who contributed to this project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#if 0 +#define DEBUG 0xFFF +#endif + +#if 0 +#define DEBUG 0x01 +#endif + +/* + * High Level Configuration Options + * (easy to change) +*/ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ +#define CONFIG_V38B 1 /* ... on V38B board */ +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ +#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ +#define CONFIG_HW_WATCHDOG 1 /* has watchdog */ + +#define CONFIG_NETCONSOLE 1 + +#define CONFIG_BOARD_EARLY_INIT_R 1 /* make flash read/write */ + +#define CFG_XLB_PIPELINING 1 /* gives better performance */ + + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + + +/* + * DDR + */ +#define SDRAM_DDR 1 /* is DDR */ +/* Settings for XLB = 132 MHz */ +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x704f0f00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x47770000 +#define SDRAM_TAPDELAY 0x10000000 + + +/* + * PCI - no suport + */ +#undef CONFIG_PCI + +/* + * Partitions + */ +#define CONFIG_MAC_PARTITION 1 +#define CONFIG_DOS_PARTITION 1 + +/* + * USB + */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IDE | \ + CFG_CMD_PING | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_IRQ | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_MII | \ + CFG_CMD_SDRAMi | \ + CFG_CMD_DATE | \ + CFG_CMD_USB | \ + CFG_CMD_FAT) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Boot low with 16 MB Flash + */ +# define CFG_LOWBOOT 1 +# define CFG_LOWBOOT16 1 + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "devno=5\0" \ + "hostname=V38B_$(devno)\0" \ + "ipaddr=10.100.99.$(devno)\0" \ + "netmask=255.255.0.0\0" \ + "serverip=10.100.10.90\0" \ + "gatewayip=10.100.254.254\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=mpc5200/uImage\0" \ + "bootcmd=run net_nfs\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):" \ + "$(netmask):$(hostname):$(netdev):off panic=1\0" \ + "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;bootm $(kernel_addr) " \ + "$(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs " \ + "addip;bootm\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +#if defined(CONFIG_MPC5200) +/* + * IPB Bus clocking configuration. + */ +#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#endif +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */ + +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 + +/* + * RTC configuration + */ +#define CFG_I2C_RTC_ADDR 0x51 + +/* + * Flash configuration - use CFI driver + */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_CFI_AMD_RESET 1 +#define CFG_FLASH_BASE 0xFF000000 +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_FLASH_SIZE 0x01000000 /* 16 MiB */ +#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000) +#define CFG_ENV_SIZE 0x10000 +#define CFG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_OVERWRITE 1 + +/* + * Memory map + */ +#define CFG_MBAR 0xF0000000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_DEFAULT_MBAR 0x80000000 + +/* Use SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII 1 + +/* + * GPIO configuration + */ +#define CFG_GPS_PORT_CONFIG 0x90000404 + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE +#else +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL 0 +#endif + + +#define CFG_BOOTCS_START CFG_FLASH_BASE +#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE +#define CFG_BOOTCS_CFG 0x00047801 +#define CFG_CS0_START CFG_FLASH_BASE +#define CFG_CS0_SIZE CFG_FLASH_SIZE + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333333 + +#define CFG_RESET_ADDRESS 0xff000000 + +/*----------------------------------------------------------------------- + * USB stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_USB_CLOCK 0x0001BBBB +#define CONFIG_USB_CONFIG 0x00001000 + + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_RESET /* reset for ide supported */ +#define CONFIG_IDE_PREINIT + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CFG_ATA_STRIDE 4 + +/* Status LED */ + +#define CONFIG_STATUS_LED /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ + +#define CFG_LED_BASE (0xf0000600 + 0x70) /* Timer 7 GPIO */ + +#ifndef __ASSEMBLY__ +/* LEDs */ +typedef unsigned int led_id_t; + +#define __led_toggle(_msk) \ + do { \ + *((volatile long *) (CFG_LED_BASE)) ^= (_msk); \ + } while(0) + +#define __led_set(_msk, _st) \ + do { \ + if ((_st)) \ + *((volatile long *) (CFG_LED_BASE)) &= ~(_msk); \ + else \ + *((volatile long *) (CFG_LED_BASE)) |= (_msk); \ + } while(0) + +#define __led_init(_msk, st) \ + { \ + *((volatile long *) (CFG_LED_BASE)) |= 0x34; \ + } + +#endif + +#endif /* __CONFIG_H */ |