diff options
Diffstat (limited to 'include/configs/ac14xx.h')
| -rw-r--r-- | include/configs/ac14xx.h | 516 |
1 files changed, 0 insertions, 516 deletions
diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h deleted file mode 100644 index 4eb8f39aaf..0000000000 --- a/include/configs/ac14xx.h +++ /dev/null @@ -1,516 +0,0 @@ -/* - * (C) Copyright 2009 Wolfgang Denk <wd@denx.de> - * (C) Copyright 2010 DAVE Srl <www.dave.eu> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * ifm AC14xx (MPC5121e based) board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_AC14XX 1 - -/* - * Memory map for the ifm AC14xx board: - * - * 0x0000_0000-0x0FFF_FFFF DDR RAM (256 MB) - * 0x3000_0000-0x3001_FFFF On Chip SRAM (128 KB) - * 0x8000_0000-0x803F_FFFF IMMR (4 MB) - * 0xE000_0000-0xEFFF_FFFF several LPB attached hardware (CSx) - * 0xFC00_0000-0xFFFF_FFFF NOR Boot FLASH (64 MB) - */ - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_SYS_MPC512X_CLKIN 25000000 /* in Hz */ -#define SCFR1_IPS_DIV 2 -#define SCFR1_LPC_DIV 2 -#define SCFR1_NFC_DIV 2 -#define SCFR1_DIU_DIV 240 - -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_IMMR 0x80000000 -#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR + 0x2100) - -/* more aggressive 'mtest' over a wider address range */ -#define CONFIG_SYS_ALT_MEMTEST -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x0FE00000 - -/* - * DDR Setup - manually set all parameters as there's no SPD etc. - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_MAX_RAM_SIZE 0x20000000 - -/* - * DDR Controller Configuration - * - * SYS_CFG: - * [31:31] MDDRC Soft Reset: Diabled - * [30:30] DRAM CKE pin: Enabled - * [29:29] DRAM CLK: Enabled - * [28:28] Command Mode: Enabled (For initialization only) - * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] - * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] - * [20:19] Read Test: DON'T USE - * [18:18] Self Refresh: Enabled - * [17:17] 16bit Mode: Disabled - * [16:13] Ready Delay: 2 - * [12:12] Half DQS Delay: Disabled - * [11:11] Quarter DQS Delay: Disabled - * [10:08] Write Delay: 2 - * [07:07] Early ODT: Disabled - * [06:06] On DIE Termination: Disabled - * [05:05] FIFO Overflow Clear: DON'T USE here - * [04:04] FIFO Underflow Clear: DON'T USE here - * [03:03] FIFO Overflow Pending: DON'T USE here - * [02:02] FIFO Underlfow Pending: DON'T USE here - * [01:01] FIFO Overlfow Enabled: Enabled - * [00:00] FIFO Underflow Enabled: Enabled - * TIME_CFG0 - * [31:16] DRAM Refresh Time: 0 CSB clocks - * [15:8] DRAM Command Time: 0 CSB clocks - * [07:00] DRAM Precharge Time: 0 CSB clocks - * TIME_CFG1 - * [31:26] DRAM tRFC: - * [25:21] DRAM tWR1: - * [20:17] DRAM tWRT1: - * [16:11] DRAM tDRR: - * [10:05] DRAM tRC: - * [04:00] DRAM tRAS: - * TIME_CFG2 - * [31:28] DRAM tRCD: - * [27:23] DRAM tFAW: - * [22:19] DRAM tRTW1: - * [18:15] DRAM tCCD: - * [14:10] DRAM tRTP: - * [09:05] DRAM tRP: - * [04:00] DRAM tRPA - */ - -/* - * NOTE: although this board uses DDR1 only, the common source brings defaults - * for DDR2 init sequences, that's why we have to keep those here as well - */ - -/* DDR1 -- 32bit, drive strength (pad configuration) 3 for control and data */ -#define CONFIG_SYS_IOCTRL_MUX_DDR ((0 << 6) | (3 << 3) | (3 << 0)) - -#define CONFIG_SYS_MDDRC_SYS_CFG (/* 0xEAA09100 */ 0 \ - | (1 << 31) /* RST_B */ \ - | (1 << 30) /* CKE */ \ - | (1 << 29) /* CLK_ON */ \ - | (0 << 28) /* CMD_MODE */ \ - | (5 << 25) /* DRAM_ROW_SELECT */ \ - | (5 << 21) /* DRAM_BANK_SELECT */ \ - | (0 << 18) /* SELF_REF_EN */ \ - | (0 << 17) /* 16BIT_MODE */ \ - | (4 << 13) /* RDLY */ \ - | (1 << 12) /* HALF_DQS_DLY */ \ - | (0 << 11) /* QUART_DQS_DLY */ \ - | (1 << 8) /* WDLY */ \ - | (0 << 7) /* EARLY_ODT */ \ - | (0 << 6) /* ON_DIE_TERMINATE */ \ - | (0 << 5) /* FIFO_OV_CLEAR */ \ - | (0 << 4) /* FIFO_UV_CLEAR */ \ - | (0 << 1) /* FIFO_OV_EN */ \ - | (0 << 0) /* FIFO_UV_EN */ \ - ) - -#define CONFIG_SYS_MDDRC_TIME_CFG0 0x04E03124 -#define CONFIG_SYS_MDDRC_TIME_CFG1 0x30CA1147 -#define CONFIG_SYS_MDDRC_TIME_CFG2 0x32B10864 - -/* register address only, i.e. template without values */ -#define CONFIG_SYS_MICRON_BMODE 0x01000000 -#define CONFIG_SYS_MICRON_EMODE 0x01010000 -#define CONFIG_SYS_MICRON_EMODE2 0x01020000 -#define CONFIG_SYS_MICRON_EMODE3 0x01030000 -/* - * values for mode registers (without mode register address) - */ -/* CAS 2.5 (6), burst seq (0) and length 4 (2) */ -#define CONFIG_SYS_MICRON_BMODE_PARAM 0x00000062 -#define CONFIG_SYS_MICRON_BMODE_RSTDLL 0x00000100 -/* DLL enable, reduced drive strength */ -#define CONFIG_SYS_MICRON_EMODE_PARAM 0x00000002 - -#define CONFIG_SYS_DDRCMD_NOP 0x01380000 -#define CONFIG_SYS_DDRCMD_PCHG_ALL 0x01100400 -#define CONFIG_SYS_MICRON_EMR ((1 << 24) | /* CMD_REQ */ \ - (0 << 22) | /* DRAM_CS */ \ - (0 << 21) | /* DRAM_RAS */ \ - (0 << 20) | /* DRAM_CAS */ \ - (0 << 19) | /* DRAM_WEB */ \ - (1 << 16) | /* DRAM_BS[2:0] */ \ - (0 << 15) | /* */ \ - (0 << 12) | /* A12->out */ \ - (0 << 11) | /* A11->RDQS */ \ - (0 << 10) | /* A10->DQS# */ \ - (0 << 7) | /* OCD program */ \ - (0 << 6) | /* Rtt1 */ \ - (0 << 3) | /* posted CAS# */ \ - (0 << 2) | /* Rtt0 */ \ - (1 << 1) | /* ODS */ \ - (0 << 0) /* DLL */ \ - ) -#define CONFIG_SYS_MICRON_EMR2 0x01020000 -#define CONFIG_SYS_MICRON_EMR3 0x01030000 -#define CONFIG_SYS_DDRCMD_RFSH 0x01080000 -#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 -#define CONFIG_SYS_MICRON_EMR_OCD ((1 << 24) | /* CMD_REQ */ \ - (0 << 22) | /* DRAM_CS */ \ - (0 << 21) | /* DRAM_RAS */ \ - (0 << 20) | /* DRAM_CAS */ \ - (0 << 19) | /* DRAM_WEB */ \ - (1 << 16) | /* DRAM_BS[2:0] */ \ - (0 << 15) | /* */ \ - (0 << 12) | /* A12->out */ \ - (0 << 11) | /* A11->RDQS */ \ - (1 << 10) | /* A10->DQS# */ \ - (7 << 7) | /* OCD program */ \ - (0 << 6) | /* Rtt1 */ \ - (0 << 3) | /* posted CAS# */ \ - (1 << 2) | /* Rtt0 */ \ - (0 << 1) | /* ODS */ \ - (0 << 0) /* DLL */ \ - ) - -/* - * Backward compatible definitions, - * so we do not have to change arch/powerpc/cpu/mpc512x/fixed_sdram.c - */ -#define CONFIG_SYS_DDRCMD_EM2 (CONFIG_SYS_MICRON_EMR2) -#define CONFIG_SYS_DDRCMD_EM3 (CONFIG_SYS_MICRON_EMR3) -#define CONFIG_SYS_DDRCMD_EN_DLL (CONFIG_SYS_MICRON_EMR) -#define CONFIG_SYS_DDRCMD_OCD_DEFAULT (CONFIG_SYS_MICRON_EMR_OCD) - -/* DDR Priority Manager Configuration */ -#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 -#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 -#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 -#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC -#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA -#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 -#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 -#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 - -/* - * NOR FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the CFI code */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* max flash size */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST { \ - CONFIG_SYS_FLASH_BASE + 0 * CONFIG_SYS_FLASH_SIZE, \ - } -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_PROTECTION - -/* - * SRAM support - */ -#define CONFIG_SYS_SRAM_BASE 0x30000000 -#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ - -/* - * CS related parameters - */ -/* CS0 Flash */ -#define CONFIG_SYS_CS0_CFG 0x00031110 -#define CONFIG_SYS_CS0_START 0xFC000000 -#define CONFIG_SYS_CS0_SIZE 0x04000000 -/* CS1 FRAM */ -#define CONFIG_SYS_CS1_CFG 0x00011000 -#define CONFIG_SYS_CS1_START 0xE0000000 -#define CONFIG_SYS_CS1_SIZE 0x00010000 -/* CS2 AS-i 1 */ -#define CONFIG_SYS_CS2_CFG 0x00009100 -#define CONFIG_SYS_CS2_START 0xE0100000 -#define CONFIG_SYS_CS2_SIZE 0x00080000 -/* CS3 netX */ -#define CONFIG_SYS_CS3_CFG 0x000A1140 -#define CONFIG_SYS_CS3_START 0xE0300000 -#define CONFIG_SYS_CS3_SIZE 0x00020000 -/* CS5 safety */ -#define CONFIG_SYS_CS5_CFG 0x0011F000 -#define CONFIG_SYS_CS5_START 0xE0400000 -#define CONFIG_SYS_CS5_SIZE 0x00010000 -/* CS6 AS-i 2 */ -#define CONFIG_SYS_CS6_CFG 0x00009100 -#define CONFIG_SYS_CS6_START 0xE0200000 -#define CONFIG_SYS_CS6_SIZE 0x00080000 - -/* Don't use alternative CS timing for any CS */ -#define CONFIG_SYS_CS_ALETIMING 0x00000000 -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x00000020 -#define CONFIG_SYS_CS_HOLDCYCLE 0x00000020 - -/* Use SRAM for initial stack */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) - -#ifdef CONFIG_FSL_DIU_FB -#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) -#else -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) -#endif - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 3 /* console on PSC3 */ -#define CONFIG_SYS_PSC3 -#if CONFIG_PSC_CONSOLE != 3 -#error CONFIG_PSC_CONSOLE must be 3 -#endif - -#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE -#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR -#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE -#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR - -/* - * Clocks in use - */ -#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \ - CLOCK_SCCR1_LPC_EN | \ - CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \ - CLOCK_SCCR1_PSC_EN(7) | \ - CLOCK_SCCR1_PSCFIFO_EN | \ - CLOCK_SCCR1_DDR_EN | \ - CLOCK_SCCR1_FEC_EN | \ - CLOCK_SCCR1_TPR_EN) - -#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \ - CLOCK_SCCR2_SPDIF_EN | \ - CLOCK_SCCR2_DIU_EN | \ - CLOCK_SCCR2_I2C_EN) - -#define CONFIG_CMDLINE_EDITING 1 /* command line history */ - -/* - * IIM - IC Identification Module - */ -#undef CONFIG_FSL_IIM - -/* - * Ethernet configuration - */ -#define CONFIG_MPC512x_FEC 1 -#define CONFIG_PHY_ADDR 0x1F -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_FEC_AN_TIMEOUT 1 -#define CONFIG_HAS_ETH0 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -/* This has to be a multiple of the flash sector size */ -#define CONFIG_ENV_ADDR 0xFFF40000 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_LOADS_ECHO 1 -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 - -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#ifdef CONFIG_CMD_KGDB -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 32 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* Cache Configuration */ -#define CONFIG_SYS_DCACHE_SIZE 32768 -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of 32 */ -#endif - -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ICE) -#define CONFIG_SYS_HID2 HID2_HBE - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_TIMESTAMP - -/* default load addr for tftp and bootm */ -#define CONFIG_LOADADDR 400000 - - -/* the builtin environment and standard greeting */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#define CONFIG_EXTRA_ENV_SETTINGS_DEVEL \ - "muster_nr=-00\0" \ - "fromram=run ramargs addip addtty; " \ - "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; " \ - "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; " \ - "tftp ${ramdisk_addr_r} ac14xx/uFS${muster_nr}; " \ - "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \ - "fromnfs=run nfsargs addip addtty; " \ - "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; " \ - "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; " \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "fromflash=run nfsargs addip addtty; " \ - "bootm fc020000 - fc000000\0" \ - "mtdargsrec=setenv bootargs root=/dev/mtdblock1 ro\0" \ - "recovery=run mtdargsrec addip addtty; " \ - "bootm ffd20000 - ffee0000\0" \ - "production=run ramargs addip addtty; " \ - "bootm fc020000 fc400000 fc000000\0" \ - "mtdargs=setenv bootargs root=/dev/mtdblock1 ro\0" \ - "prodmtd=run mtdargs addip addtty; " \ - "bootm fc020000 - fc000000\0" \ - "" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "u-boot_addr_r=200000\0" \ - "kernel_addr_r=600000\0" \ - "fdt_addr_r=a00000\0" \ - "ramdisk_addr_r=b00000\0" \ - "u-boot_addr=FFF00000\0" \ - "kernel_addr=FC020000\0" \ - "fdt_addr=FC000000\0" \ - "ramdisk_addr=FC400000\0" \ - "verify=n\0" \ - "ramdiskfile=ac14xx/uRamdisk\0" \ - "u-boot=ac14xx/u-boot.bin\0" \ - "bootfile=ac14xx/uImage\0" \ - "fdtfile=ac14xx/ac14xx.dtb\0" \ - "netdev=eth0\0" \ - "consdev=ttyPSC0\0" \ - "hostname=ac14xx\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}${muster_nr}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} " \ - "console=${consdev},${baudrate}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "net_self=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${ramdisk_addr_r} ${ramdiskfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run ramargs addip addtty;" \ - "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\ - "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ - "update=protect off ${u-boot_addr} +${filesize};" \ - "era ${u-boot_addr} +${filesize};" \ - "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \ - CONFIG_EXTRA_ENV_SETTINGS_DEVEL \ - "upd=run load update\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run production" - -#define CONFIG_ARP_TIMEOUT 200UL - -#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1 - -#define OF_CPU "PowerPC,5121@0" -#define OF_SOC_COMPAT "fsl,mpc5121-immr" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc@80000000/serial@11300" - -#endif /* __CONFIG_H */ |