summaryrefslogtreecommitdiff
path: root/include/configs/acadia.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/acadia.h')
-rw-r--r--include/configs/acadia.h217
1 files changed, 108 insertions, 109 deletions
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index ed2754d66a..52ccdb5b9d 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -42,7 +42,7 @@
#include "amcc-common.h"
/* Detect Acadia PLL input clock automatically via CPLD bit */
-#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
+#define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_CPLD_BASE + 0) == 0x0c) ? \
66666666 : 33333000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
@@ -66,71 +66,71 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_FLASH_BASE 0xfe000000
-#define CFG_CPLD_BASE 0x80000000
-#define CFG_NAND_ADDR 0xd0000000
-#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
+#define CONFIG_SYS_FLASH_BASE 0xfe000000
+#define CONFIG_SYS_CPLD_BASE 0x80000000
+#define CONFIG_SYS_NAND_ADDR 0xd0000000
+#define CONFIG_SYS_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
-#define CFG_TEMP_STACK_OCM 1 /* OCM as init ram */
+#define CONFIG_SYS_TEMP_STACK_OCM 1 /* OCM as init ram */
/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xf8000000
-#define CFG_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xf8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SRAM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#define CFG_BASE_BAUD 691200
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_SYS_BASE_BAUD 691200
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#else
-#define CFG_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */
+#define CONFIG_SYS_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */
#endif
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
/*
@@ -151,69 +151,68 @@
* set up. While still running from cache, I experienced problems accessing
* the NAND controller. sr - 2006-08-25
*/
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
-
-#define CFG_NAND_ECCSIZE 256
-#define CFG_NAND_ECCBYTES 3
-#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
-#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
-
-#ifdef CFG_ENV_IS_IN_NAND
+#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 16
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* RAM (CRAM)
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_RAM 64 /* 64MB */
+#define CONFIG_SYS_MBYTES_RAM 64 /* 64MB */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
/*-----------------------------------------------------------------------
* Ethernet
@@ -262,64 +261,64 @@
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_NAND_CS 3
+#define CONFIG_SYS_NAND_CS 3
/* Memory Bank 0 (Flash) initialization */
-#define CFG_EBC_PB0AP 0x03337200
-#define CFG_EBC_PB0CR 0xfe0bc000
+#define CONFIG_SYS_EBC_PB0AP 0x03337200
+#define CONFIG_SYS_EBC_PB0CR 0xfe0bc000
/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB3AP 0x018003c0
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
/* Memory Bank 1 (CRAM) initialization */
-#define CFG_EBC_PB1AP 0x030400c0
-#define CFG_EBC_PB1CR 0x000bc000
+#define CONFIG_SYS_EBC_PB1AP 0x030400c0
+#define CONFIG_SYS_EBC_PB1CR 0x000bc000
/* Memory Bank 2 (CRAM) initialization */
-#define CFG_EBC_PB2AP 0x030400c0
-#define CFG_EBC_PB2CR 0x020bc000
+#define CONFIG_SYS_EBC_PB2AP 0x030400c0
+#define CONFIG_SYS_EBC_PB2CR 0x020bc000
#else
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
/*
* When NAND-booting the CRAM EBC setup must be done in sync mode, since the
* NAND-SPL already initialized the CRAM and EBC to sync mode.
*/
/* Memory Bank 1 (CRAM) initialization */
-#define CFG_EBC_PB1AP 0x9C0201C0
-#define CFG_EBC_PB1CR 0x000bc000
+#define CONFIG_SYS_EBC_PB1AP 0x9C0201C0
+#define CONFIG_SYS_EBC_PB1CR 0x000bc000
/* Memory Bank 2 (CRAM) initialization */
-#define CFG_EBC_PB2AP 0x9C0201C0
-#define CFG_EBC_PB2CR 0x020bc000
+#define CONFIG_SYS_EBC_PB2AP 0x9C0201C0
+#define CONFIG_SYS_EBC_PB2CR 0x020bc000
#endif
/* Memory Bank 4 (CPLD) initialization */
-#define CFG_EBC_PB4AP 0x04006000
-#define CFG_EBC_PB4CR (CFG_CPLD_BASE | 0x18000)
+#define CONFIG_SYS_EBC_PB4AP 0x04006000
+#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_CPLD_BASE | 0x18000)
-#define CFG_EBC_CFG 0xf8400000
+#define CONFIG_SYS_EBC_CFG 0xf8400000
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-#define CFG_GPIO_CRAM_CLK 8
-#define CFG_GPIO_CRAM_WAIT 9 /* GPIO-In */
-#define CFG_GPIO_CRAM_ADV 10
-#define CFG_GPIO_CRAM_CRE (32 + 21) /* GPIO-Out */
+#define CONFIG_SYS_GPIO_CRAM_CLK 8
+#define CONFIG_SYS_GPIO_CRAM_WAIT 9 /* GPIO-In */
+#define CONFIG_SYS_GPIO_CRAM_ADV 10
+#define CONFIG_SYS_GPIO_CRAM_CRE (32 + 21) /* GPIO-Out */
/*-----------------------------------------------------------------------
* Definitions for GPIO_0 setup (PPC405EZ specific)
@@ -341,13 +340,13 @@
* GPIO0[28-30] - Trace Outputs / PWM Inputs
* GPIO0[31] - PWM_8 I/O
*/
-#define CFG_GPIO0_TCR 0xC0A00000
-#define CFG_GPIO0_OSRL 0x50004400
-#define CFG_GPIO0_OSRH 0x02000055
-#define CFG_GPIO0_ISR1L 0x00001000
-#define CFG_GPIO0_ISR1H 0x00000055
-#define CFG_GPIO0_TSRL 0x02000000
-#define CFG_GPIO0_TSRH 0x00000055
+#define CONFIG_SYS_GPIO0_TCR 0xC0A00000
+#define CONFIG_SYS_GPIO0_OSRL 0x50004400
+#define CONFIG_SYS_GPIO0_OSRH 0x02000055
+#define CONFIG_SYS_GPIO0_ISR1L 0x00001000
+#define CONFIG_SYS_GPIO0_ISR1H 0x00000055
+#define CONFIG_SYS_GPIO0_TSRL 0x02000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000055
/*-----------------------------------------------------------------------
* Definitions for GPIO_1 setup (PPC405EZ specific)
@@ -363,12 +362,12 @@
* GPIO1[16] - SPI_SS_1_N Output
* GPIO1[17-20] - Trace Output/External Interrupts IRQ0 - IRQ3 inputs
*/
-#define CFG_GPIO1_TCR 0xFFFF8414
-#define CFG_GPIO1_OSRL 0x40000110
-#define CFG_GPIO1_OSRH 0x55455555
-#define CFG_GPIO1_ISR1L 0x15555445
-#define CFG_GPIO1_ISR1H 0x00000000
-#define CFG_GPIO1_TSRL 0x00000000
-#define CFG_GPIO1_TSRH 0x00000000
+#define CONFIG_SYS_GPIO1_TCR 0xFFFF8414
+#define CONFIG_SYS_GPIO1_OSRL 0x40000110
+#define CONFIG_SYS_GPIO1_OSRH 0x55455555
+#define CONFIG_SYS_GPIO1_ISR1L 0x15555445
+#define CONFIG_SYS_GPIO1_ISR1H 0x00000000
+#define CONFIG_SYS_GPIO1_TSRL 0x00000000
+#define CONFIG_SYS_GPIO1_TSRH 0x00000000
#endif /* __CONFIG_H */