diff options
Diffstat (limited to 'include/configs/ads5121.h')
| -rw-r--r-- | include/configs/ads5121.h | 401 |
1 files changed, 401 insertions, 0 deletions
diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h new file mode 100644 index 0000000000..22eac1b4b9 --- /dev/null +++ b/include/configs/ads5121.h @@ -0,0 +1,401 @@ +/* + * (C) Copyright 2007 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * ADS5121 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define DEBUG +#undef DEBUG + +/* + * Memory map for the ADS5121 board: + * + * 0x0000_0000 - 0x0FFF_FFFF DDR RAM (256 MB) + * 0x3000_0000 - 0x3001_FFFF SRAM (128 KB) + * 0x8000_0000 - 0x803F_FFFF IMMR (4 MB) + * 0x8200_0000 - 0x8200_001F CPLD (32 B) + * 0xFC00_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB) + */ + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_MPC512X 1 /* MPC512X family */ + +#undef CONFIG_PCI + +#define CFG_MPC512X_CLKIN 66000000 /* in Hz */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */ + +#define CFG_IMMR 0x80000000 + +#define CFG_MEMTEST_START 0x00200000 /* memtest region */ +#define CFG_MEMTEST_END 0x00400000 + +/* + * DDR Setup - manually set all parameters as there's no SPD etc. + */ +#define CFG_DDR_SIZE 256 /* MB */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_BASE + +/* DDR Controller Configuration + * + * SYS_CFG: + * [31:31] MDDRC Soft Reset: Diabled + * [30:30] DRAM CKE pin: Enabled + * [29:29] DRAM CLK: Enabled + * [28:28] Command Mode: Enabled (For initialization only) + * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] + * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] + * [20:19] Read Test: DON'T USE + * [18:18] Self Refresh: Enabled + * [17:17] 16bit Mode: Disabled + * [16:13] Ready Delay: 2 + * [12:12] Half DQS Delay: Disabled + * [11:11] Quarter DQS Delay: Disabled + * [10:08] Write Delay: 2 + * [07:07] Early ODT: Disabled + * [06:06] On DIE Termination: Disabled + * [05:05] FIFO Overflow Clear: DON'T USE here + * [04:04] FIFO Underflow Clear: DON'T USE here + * [03:03] FIFO Overflow Pending: DON'T USE here + * [02:02] FIFO Underlfow Pending: DON'T USE here + * [01:01] FIFO Overlfow Enabled: Enabled + * [00:00] FIFO Underflow Enabled: Enabled + * TIME_CFG0 + * [31:16] DRAM Refresh Time: 0 CSB clocks + * [15:8] DRAM Command Time: 0 CSB clocks + * [07:00] DRAM Precharge Time: 0 CSB clocks + * TIME_CFG1 + * [31:26] DRAM tRFC: + * [25:21] DRAM tWR1: + * [20:17] DRAM tWRT1: + * [16:11] DRAM tDRR: + * [10:05] DRAM tRC: + * [04:00] DRAM tRAS: + * TIME_CFG2 + * [31:28] DRAM tRCD: + * [27:23] DRAM tFAW: + * [22:19] DRAM tRTW1: + * [18:15] DRAM tCCD: + * [14:10] DRAM tRTP: + * [09:05] DRAM tRP: + * [04:00] DRAM tRPA + */ + +#define CFG_MDDRC_SYS_CFG 0xF8604200 +#define CFG_MDDRC_SYS_CFG_RUN 0xE8604200 +#define CFG_MDDRC_SYS_CFG_EN 0x30000000 +#define CFG_MDDRC_TIME_CFG0 0x0000281E +#define CFG_MDDRC_TIME_CFG0_RUN 0x01F4281E +#define CFG_MDDRC_TIME_CFG1 0x54EC1168 +#define CFG_MDDRC_TIME_CFG2 0x35210864 + +#define CFG_MICRON_NOP 0x01380000 +#define CFG_MICRON_PCHG_ALL 0x01100400 +#define CFG_MICRON_MR 0x01000022 +#define CFG_MICRON_EM2 0x01020000 +#define CFG_MICRON_EM3 0x01030000 +#define CFG_MICRON_EN_DLL 0x01010000 +#define CFG_MICRON_RST_DLL 0x01000932 +#define CFG_MICRON_RFSH 0x01080000 +#define CFG_MICRON_INIT_DEV_OP 0x01000832 +#define CFG_MICRON_OCD_DEFAULT 0x01010780 +#define CFG_MICRON_OCD_EXIT 0x01010400 + +/* DDR Priority Manager Configuration */ +#define CFG_MDDRCGRP_PM_CFG1 0x000777AA +#define CFG_MDDRCGRP_PM_CFG2 0x00000055 +#define CFG_MDDRCGRP_HIPRIO_CFG 0x00000000 +#define CFG_MDDRCGRP_LUT0_MU 0x11111117 +#define CFG_MDDRCGRP_LUT0_ML 0x7777777A +#define CFG_MDDRCGRP_LUT1_MU 0x4444EEEE +#define CFG_MDDRCGRP_LUT1_ML 0xEEEEEEEE +#define CFG_MDDRCGRP_LUT2_MU 0x44444444 +#define CFG_MDDRCGRP_LUT2_ML 0x44444444 +#define CFG_MDDRCGRP_LUT3_MU 0x55555555 +#define CFG_MDDRCGRP_LUT3_ML 0x55555558 +#define CFG_MDDRCGRP_LUT4_MU 0x11111111 +#define CFG_MDDRCGRP_LUT4_ML 0x1111117C +#define CFG_MDDRCGRP_LUT0_AU 0x33333377 +#define CFG_MDDRCGRP_LUT0_AL 0x7777EEEE +#define CFG_MDDRCGRP_LUT1_AU 0x11111111 +#define CFG_MDDRCGRP_LUT1_AL 0x11111111 +#define CFG_MDDRCGRP_LUT2_AU 0x11111111 +#define CFG_MDDRCGRP_LUT2_AL 0x11111111 +#define CFG_MDDRCGRP_LUT3_AU 0x11111111 +#define CFG_MDDRCGRP_LUT3_AL 0x11111111 +#define CFG_MDDRCGRP_LUT4_AU 0x11111111 +#define CFG_MDDRCGRP_LUT4_AL 0x11111111 + +/* + * NOR FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFC000000 /* start of FLASH */ +#define CFG_FLASH_SIZE 0x04000000 /* max flash size in bytes */ +#define CFG_FLASH_USE_BUFFER_WRITE + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} +#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CFG_FLASH_CHECKSUM + +/* + * CPLD registers area is really only 32 bytes in size, but the smallest possible LP + * window is 64KB + */ +#define CFG_CPLD_BASE 0x82000000 +#define CFG_CPLD_SIZE 0x00010000 /* 64 KB */ + +#define CFG_SRAM_BASE 0x30000000 +#define CFG_SRAM_SIZE 0x00020000 /* 128 KB */ + +#define CFG_CS0_CFG 0x05059310 /* ALE active low, data size 4bytes */ +#define CFG_CS2_CFG 0x05059010 /* ALE active low, data size 1byte */ + +/* Use SRAM for initial stack */ +#define CFG_INIT_RAM_ADDR CFG_SRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END CFG_SRAM_SIZE /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE /* Start of monitor */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ +#if CONFIG_PSC_CONSOLE != 3 +#error CONFIG_PSC_CONSOLE must be 3 +#endif +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE +#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR +#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE +#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#if 0 +#define CFG_I2C_NOPROBES {{0,0x69}} * Don't probe these addrs */ +#endif + +/* + * Ethernet configuration + */ +#define CONFIG_MPC512x_FEC 1 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_ADDR 0x1 +#define CONFIG_MII 1 /* MII PHY management */ + +#if 0 +/* + * Configure on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ +#endif + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +/* This has to be a multiple of the Flash sector size */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +/* + * Watchdog timeout = CFG_WATCHDOG_VALUE * 65536 / IPS clock. + * For example, when IPS is set to 66MHz and CFG_WATCHDOG_VALUE is set + * to 0xFFFF, watchdog timeouts after about 64s. For details refer + * to chapter 36 of the MPC5121e Reference Manual. + */ +#define CONFIG_WATCHDOG /* enable watchdog */ +#define CFG_WATCHDOG_VALUE 0xFFFF + + /* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#ifdef CONFIG_CMD_KGDB + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + + +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#ifdef CONFIG_CMD_KGDB +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_HOSTNAME ads5121 +#define CONFIG_BOOTFILE uImage + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "load=tftp 200000 /tftpboot/ads5121/u-boot.bin\0" \ + "update=protect off FFF00000 +${filesize};" \ + "era FFF00000 +${filesize};cp.b 200000 FFF00000 ${filesize}\0" \ + "upd=run load;run update\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#endif /* __CONFIG_H */ |