diff options
Diffstat (limited to 'include/configs/eXalion.h')
| -rw-r--r-- | include/configs/eXalion.h | 454 |
1 files changed, 454 insertions, 0 deletions
diff --git a/include/configs/eXalion.h b/include/configs/eXalion.h new file mode 100644 index 0000000000..5ebc7a9cc8 --- /dev/null +++ b/include/configs/eXalion.h @@ -0,0 +1,454 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC824X 1 +/* #define CONFIG_MPC8240 1 */ +#define CONFIG_MPC8245 1 +#define CONFIG_EXALION 1 + +#if defined (CONFIG_MPC8240) + /* #warning ---------- eXalion with MPC8240 --------------- */ +#elif defined (CONFIG_MPC8245) + /* #warning ++++++++++ eXalion with MPC8245 +++++++++++++++ */ +#elif defined (CONFIG_MPC8245) && defined (CONFIG_MPC8245) +#error #### Both types of MPC824x defined (CONFIG_8240 and CONFIG_8245) +#else +#error #### Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif +/* older kernels need clock in MHz newer in Hz */ + /* #define CONFIG_CLOCKS_IN_MHZ 1 *//* clocks passsed to Linux in MHz */ +#undef CONFIG_CLOCKS_IN_MHZ + +#define CONFIG_BOOTDELAY 10 + + + /*#define CONFIG_DRAM_SPEED 66 *//* MHz */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_FLASH | \ + CFG_CMD_SDRAM | \ + CFG_CMD_I2C | \ + CFG_CMD_IDE | \ + CFG_CMD_FAT | \ + CFG_CMD_ENV | \ + CFG_CMD_PCI ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + */ +#define CFG_LONGHELP 1 /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 8 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_MISC_INIT_R 1 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_MAX_RAM_SIZE 0x10000000 /* 1 GBytes - initdram() will */ + /* return real value. */ + +#define CFG_RESET_ADDRESS 0xFFF00100 + +#undef CFG_RAMBOOT +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE TEXT_BASE + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + */ +#define CFG_INIT_DATA_SIZE 128 + +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x1000 +#define CFG_INIT_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE) + +#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + +#if defined (CONFIG_MPC8240) +#define CFG_FLASH_BASE 0xFFE00000 +#define CFG_FLASH_SIZE (2 * 1024 * 1024) /* onboard 2MByte flash */ +#elif defined (CONFIG_MPC8245) +#define CFG_FLASH_BASE 0xFFC00000 +#define CFG_FLASH_SIZE (4 * 1024 * 1024) /* onboard 4MByte flash */ +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SECT_SIZE 0x20000 /* Size of one Flash sector */ +#define CFG_ENV_SIZE CFG_ENV_SECT_SIZE /* Use one Flash sector for enviroment */ +#define CFG_ENV_ADDR 0xFFFC0000 +#define CFG_ENV_OFFSET 0 /* starting right at the beginning */ + +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +#define CFG_ALT_MEMTEST 1 /* use real memory test */ +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ + +#define CFG_EUMB_ADDR 0xFC000000 + +/* #define CFG_ISA_MEM 0xFD000000 */ +#define CFG_ISA_IO 0xFE000000 + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors per flash */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define FLASH_BASE0_PRELIM CFG_FLASH_BASE +#define FLASH_BASE1_PRELIM 0 + + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_FLASH_INCREMENT 0 /* there is only one bank */ +#define CFG_FLASH_PROTECTION 1 /* use hardware protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + + +/*----------------------------------------------------------------------- + * PCI stuff + */ +#define CONFIG_PCI 1 /* include pci support */ +#undef CONFIG_PCI_PNP + +#define CONFIG_NET_MULTI 1 /* Multi ethernet cards support */ + +#define CONFIG_EEPRO100 1 + +#define PCI_ENET0_MEMADDR 0x80000000 /* Intel 82559ER */ +#define PCI_ENET0_IOADDR 0x80000000 +#define PCI_ENET1_MEMADDR 0x81000000 /* Intel 82559ER */ +#define PCI_ENET1_IOADDR 0x81000000 +#define PCI_ENET2_MEMADDR 0x82000000 /* Broadcom BCM569xx */ +#define PCI_ENET2_IOADDR 0x82000000 +#define PCI_ENET3_MEMADDR 0x83000000 /* Broadcom BCM56xx */ +#define PCI_ENET3_IOADDR 0x83000000 + +/*----------------------------------------------------------------------- + * NS16550 Configuration + */ +#define CFG_NS16550 1 +#define CFG_NS16550_SERIAL 1 + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 38400 + +#define CFG_NS16550_REG_SIZE 1 + +#if (CONFIG_CONS_INDEX == 1) +#define CFG_NS16550_CLK 1843200 /* COM1 only ! */ +#else +#define CFG_NS16550_CLK ({ extern ulong get_bus_freq (ulong); get_bus_freq (0); }) +#endif + +#define CFG_NS16550_COM1 (CFG_ISA_IO + 0x3F8) +#define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4500) +#define CFG_NS16550_COM3 (CFG_EUMB_ADDR + 0x4600) + +/*----------------------------------------------------------------------- + * select i2c support configuration + * + * Supported configurations are {none, software, hardware} drivers. + * If the software driver is chosen, there are some additional + * configuration items that the driver uses to drive the port pins. + */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/*----------------------------------------------------------------------- + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +#define CFG_HZ 1000 + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 /* for MPC8240 only */ + + /*#define CONFIG_133MHZ_DRAM 1 *//* For 133 MHZ DRAM only !!!!!!!!!!! */ + +#if defined (CONFIG_MPC8245) +/* Bit-field values for PMCR2. */ +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_DLL_EXTEND 0x80 /* use DLL extended range - 133MHz only */ +#define CFG_PCI_HOLD_DEL 0x20 /* delay and hold timing - 133MHz only */ +#endif + +/* Bit-field values for MIOCR1. */ +#if !defined (CONFIG_133MHZ_DRAM) +#define CFG_DLL_MAX_DELAY 0x04 /* longer DLL delay line - 66MHz only */ +#endif +/* Bit-field values for MIOCR2. */ +#define CFG_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay */ + /* - note bottom 3 bits MUST be 0 */ +#endif + +/* Bit-field values for MCCR1. */ +#define CFG_ROMNAL 7 /*rom/flash next access time */ +#define CFG_ROMFAL 11 /*rom/flash access time */ + +/* Bit-field values for MCCR2. */ +#define CFG_TSWAIT 0x5 /* Transaction Start Wait States timer */ +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_REFINT 1300 /* no of clock cycles between CBR */ +#else /* refresh cycles */ +#define CFG_REFINT 750 +#endif + +/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_BSTOPRE 1023 +#else +#define CFG_BSTOPRE 250 +#endif + +/* Bit-field values for MCCR3. */ +/* the following are for SDRAM only */ + +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_REFREC 9 /* Refresh to activate interval */ +#else +#define CFG_REFREC 5 /* Refresh to activate interval */ +#endif +#if defined (CONFIG_MPC8240) +#define CFG_RDLAT 2 /* data latency from read command */ +#endif + +/* Bit-field values for MCCR4. */ +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_PRETOACT 3 /* Precharge to activate interval */ +#define CFG_ACTTOPRE 7 /* Activate to Precharge interval */ +#define CFG_ACTORW 5 /* Activate to R/W */ +#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ +#else +#if 0 +#define CFG_PRETOACT 2 /* Precharge to activate interval */ +#define CFG_ACTTOPRE 3 /* Activate to Precharge interval */ +#define CFG_ACTORW 3 /* Activate to R/W */ +#define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */ +#endif +#define CFG_PRETOACT 2 /* Precharge to activate interval */ +#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */ +#define CFG_ACTORW 3 /* Activate to R/W */ +#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ +#endif +#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ +#define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ +#define CFG_REGDIMM 0 +#if defined (CONFIG_MPC8240) +#define CFG_REGISTERD_TYPE_BUFFER 0 +#elif defined (CONFIG_MPC8245) +#define CFG_REGISTERD_TYPE_BUFFER 1 +#define CFG_EXTROM 0 +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + + +/*----------------------------------------------------------------------- + memory bank settings + * only bits 20-29 are actually used from these vales to set the + * start/end address the upper two bits will be 0, and the lower 20 + * bits will be set to 0x00000 for a start address, or 0xfffff for an + * end address + */ +#define CFG_BANK0_START 0x00000000 +#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) +#define CFG_BANK0_ENABLE 1 +#define CFG_BANK1_START 0x3ff00000 +#define CFG_BANK1_END 0x3fffffff +#define CFG_BANK1_ENABLE 0 +#define CFG_BANK2_START 0x3ff00000 +#define CFG_BANK2_END 0x3fffffff +#define CFG_BANK2_ENABLE 0 +#define CFG_BANK3_START 0x3ff00000 +#define CFG_BANK3_END 0x3fffffff +#define CFG_BANK3_ENABLE 0 +#define CFG_BANK4_START 0x00000000 +#define CFG_BANK4_END 0x00000000 +#define CFG_BANK4_ENABLE 0 +#define CFG_BANK5_START 0x00000000 +#define CFG_BANK5_END 0x00000000 +#define CFG_BANK5_ENABLE 0 +#define CFG_BANK6_START 0x00000000 +#define CFG_BANK6_END 0x00000000 +#define CFG_BANK6_ENABLE 0 +#define CFG_BANK7_START 0x00000000 +#define CFG_BANK7_END 0x00000000 +#define CFG_BANK7_ENABLE 0 + +/*----------------------------------------------------------------------- + * Memory bank enable bitmask, specifying which of the banks defined above + are actually present. MSB is for bank #7, LSB is for bank #0. + */ +#define CFG_BANK_ENABLE 0x01 + +#if defined (CONFIG_MPC8240) +#define CFG_ODCR 0xDF /* configures line driver impedances, */ + /* see 8240 book for bit definitions */ +#elif defined (CONFIG_MPC8245) +#if defined (CONFIG_133MHZ_DRAM) +#define CFG_ODCR 0xFE /* configures line driver impedances - 133MHz */ +#else +#define CFG_ODCR 0xDE /* configures line driver impedances - 66MHz */ +#endif +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + +#define CFG_PGMAX 0x32 /* how long the 8240 retains the */ + /* currently accessed page in memory */ + /* see 8240 book for details */ + +/*----------------------------------------------------------------------- + * Block Address Translation (BAT) register settings. + */ +/* SDRAM 0 - 256MB */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* stack in DCACHE @ 1GB (no backing mem) */ +#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) + +/* PCI memory */ +#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +/* Flash, config addrs, etc */ +#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +/*----------------------------------------------------------------------- + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/* values according to the manual */ +#define CONFIG_DRAM_50MHZ 1 +#define CONFIG_SDRAM_50MHZ + +#undef NR_8259_INTS +#define NR_8259_INTS 1 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + */ +#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */ +#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 2 drives per IDE bus */ + +#define CFG_ATA_BASE_ADDR CFG_ISA_IO /* base address */ +#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ +#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ +#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */ +#define CFG_ATA_REG_OFFSET 0 /* reg offset */ +#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */ + +#define CONFIG_ATAPI + +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* reset for ide supported... */ +#undef CONFIG_IDE_RESET_ROUTINE /* with a special reset function */ + +/*----------------------------------------------------------------------- + * DISK Partition support + */ +#define CONFIG_DOS_PARTITION + +/*----------------------------------------------------------------------- + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#endif /* __CONFIG_H */ |