diff options
Diffstat (limited to 'include/configs/katmai.h')
-rw-r--r-- | include/configs/katmai.h | 287 |
1 files changed, 0 insertions, 287 deletions
diff --git a/include/configs/katmai.h b/include/configs/katmai.h deleted file mode 100644 index 3f39a26d3b..0000000000 --- a/include/configs/katmai.h +++ /dev/null @@ -1,287 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * katmai.h - configuration for AMCC Katmai (440SPe) - ***********************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_KATMAI 1 /* Board is Katmai */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_440SPE 1 /* Specifc SPe support */ -#define CONFIG_440SPE_REVA 1 /* Support old Rev A. */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ -#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 - -/* - * Enable this board for more than 2GB of SDRAM - */ -#define CONFIG_VERY_BIG_RAM - -/* - * Include common defines/options for all AMCC eval boards - */ -#define CONFIG_HOSTNAME katmai -#include "amcc-common.h" - -#undef CONFIG_SHOW_BOOT_PROGRESS - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ -#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ - -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE - -#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ -#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ - -#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000 -#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000 -#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000 -#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000 -#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000 -#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000 - -/* base address of inbound PCIe window */ -#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL - -/* System RAM mapped to PCI space */ -#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE -#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE -#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) - -#define CONFIG_SYS_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in internal SRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ -#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/ -#define CONFIG_DDR_ECC 1 /* with ECC support */ -#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/ -#undef CONFIG_STRESS - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 - -#define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */ - -#define IIC0_BOOTPROM_ADDR 0x50 -#define IIC0_ALT_BOOTPROM_ADDR 0x54 - -#define CONFIG_SYS_I2C_EEPROM_ADDR (0x50) -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* I2C bootstrap EEPROM */ -#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50 -#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 -#define CONFIG_4xx_CONFIG_BLOCKSIZE 8 - -/* I2C RTC */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_POWERPC \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=ff000000\0" \ - "fdt_addr=ff1e0000\0" \ - "ramdisk_addr=ff200000\0" \ - "pciconfighost=1\0" \ - "pcie_mode=RP:RP:RP\0" \ - "" - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SDRAM - -#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ -#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ -#define CONFIG_HAS_ETH0 -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_RESET_DELAY 1000 -#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -/* General PCI */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CONFIG_PCI_CONFIG_HOST_BRIDGE - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -#undef CONFIG_SYS_PCI_MASTER_INIT - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */ - -/* - * NETWORK Support (PCI): - */ -/* Support for Intel 82557/82559/82559ER chips. */ -#define CONFIG_EEPRO100 - -/*----------------------------------------------------------------------- - * Xilinx System ACE support - *----------------------------------------------------------------------*/ -#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */ -#define CONFIG_SYS_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */ -#define CONFIG_SYS_SYSTEMACE_BASE CONFIG_SYS_ACE_BASE - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ - -/* Memory Bank 0 (Flash) initialization */ -#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ - EBC_BXAP_TWT_ENCODE(7) | \ - EBC_BXAP_BCE_DISABLE | \ - EBC_BXAP_BCT_2TRANS | \ - EBC_BXAP_CSN_ENCODE(0) | \ - EBC_BXAP_OEN_ENCODE(0) | \ - EBC_BXAP_WBN_ENCODE(0) | \ - EBC_BXAP_WBF_ENCODE(0) | \ - EBC_BXAP_TH_ENCODE(0) | \ - EBC_BXAP_RE_DISABLED | \ - EBC_BXAP_SOR_DELAYED | \ - EBC_BXAP_BEM_WRITEONLY | \ - EBC_BXAP_PEN_DISABLED) -#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ - EBC_BXCR_BS_16MB | \ - EBC_BXCR_BU_RW | \ - EBC_BXCR_BW_16BIT) - -/* Memory Bank 1 (Xilinx System ACE controller) initialization */ -#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ - EBC_BXAP_TWT_ENCODE(4) | \ - EBC_BXAP_BCE_DISABLE | \ - EBC_BXAP_BCT_2TRANS | \ - EBC_BXAP_CSN_ENCODE(0) | \ - EBC_BXAP_OEN_ENCODE(0) | \ - EBC_BXAP_WBN_ENCODE(0) | \ - EBC_BXAP_WBF_ENCODE(0) | \ - EBC_BXAP_TH_ENCODE(0) | \ - EBC_BXAP_RE_DISABLED | \ - EBC_BXAP_SOR_NONDELAYED | \ - EBC_BXAP_BEM_WRITEONLY | \ - EBC_BXAP_PEN_DISABLED) -#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_ACE_BASE) | \ - EBC_BXCR_BS_1MB | \ - EBC_BXCR_BU_RW | \ - EBC_BXCR_BW_16BIT) - -/*------------------------------------------------------------------------- - * Initialize EBC CONFIG - - * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC - * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 - *-------------------------------------------------------------------------*/ -#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_UNLOCK | \ - EBC_CFG_PTD_ENABLE | \ - EBC_CFG_RTC_16PERCLK | \ - EBC_CFG_ATC_PREVIOUS | \ - EBC_CFG_DTC_PREVIOUS | \ - EBC_CFG_CTC_PREVIOUS | \ - EBC_CFG_OEO_PREVIOUS | \ - EBC_CFG_EMC_DEFAULT | \ - EBC_CFG_PME_DISABLE | \ - EBC_CFG_PR_16) - -/*----------------------------------------------------------------------- - * GPIO Setup - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_GPIO_PCIE_PRESENT0 17 -#define CONFIG_SYS_GPIO_PCIE_PRESENT1 21 -#define CONFIG_SYS_GPIO_PCIE_PRESENT2 23 -#define CONFIG_SYS_GPIO_RS232_FORCEOFF 30 - -#define CONFIG_SYS_PFC0 (GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT0) | \ - GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT1) | \ - GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT2) | \ - GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)) -#define CONFIG_SYS_GPIO_OR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) -#define CONFIG_SYS_GPIO_TCR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) -#define CONFIG_SYS_GPIO_ODR 0 - -#endif /* __CONFIG_H */ |