diff options
Diffstat (limited to 'include/configs/lx2160a_common.h')
| -rw-r--r-- | include/configs/lx2160a_common.h | 289 |
1 files changed, 289 insertions, 0 deletions
diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h new file mode 100644 index 0000000000..4b5608b5a3 --- /dev/null +++ b/include/configs/lx2160a_common.h @@ -0,0 +1,289 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#ifndef __LX2_COMMON_H +#define __LX2_COMMON_H + +#include <asm/arch/stream_id_lsch3.h> +#include <asm/arch/config.h> +#include <asm/arch/soc.h> + +#define CONFIG_REMAKE_ELF +#define CONFIG_FSL_LAYERSCAPE +#define CONFIG_GICV3 +#define CONFIG_FSL_TZPC_BP147 +#define CONFIG_FSL_MEMAC + +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_FLASH_BASE 0x20000000 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F 1 + +/* DDR */ +#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ +#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 +#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL +#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 +#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL +#define CONFIG_DDR_SPD +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS3 0x53 +#define SPD_EEPROM_ADDRESS4 0x54 +#define SPD_EEPROM_ADDRESS5 0x55 +#define SPD_EEPROM_ADDRESS6 0x56 +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 +#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 2 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 +#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ +#define CONFIG_SYS_MONITOR_LEN (936 * 1024) + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) + +/* SMP Definitinos */ +#define CPU_RELEASE_ADDR secondary_boot_func + +/* Generic Timer Definitions */ +/* + * This is not an accurate number. It is used in start.S. The frequency + * will be udpated later when get_bus_freq(0) is available. + */ + +#define COUNTER_FREQUENCY 25000000 /* 25MHz */ + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) + +/* Serial Port */ +#define CONFIG_PL01X_SERIAL +#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4) +#define CONFIG_SYS_SERIAL0 0x21c0000 +#define CONFIG_SYS_SERIAL1 0x21d0000 +#define CONFIG_SYS_SERIAL2 0x21e0000 +#define CONFIG_SYS_SERIAL3 0x21f0000 +/*below might needs to be removed*/ +#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ + (void *)CONFIG_SYS_SERIAL1, \ + (void *)CONFIG_SYS_SERIAL2, \ + (void *)CONFIG_SYS_SERIAL3 } +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* MC firmware */ +#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 +#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 +#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 + +/* Define phy_reset function to boot the MC based on mcinitcmd. + * This happens late enough to properly fixup u-boot env MAC addresses. + */ +#define CONFIG_RESET_PHY_R + +/* + * Carve out a DDR region which will not be used by u-boot/Linux + * + * It will be used by MC and Debug Server. The MC region must be + * 512MB aligned, so the min size to hide is 512MB. + */ +#ifdef CONFIG_FSL_MC_ENET +#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024) +#endif + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* RTC */ +#define RTC +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Qixis */ +#define CONFIG_FSL_QIXIS +#define CONFIG_QIXIS_I2C_ACCESS +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 + +/* PCI */ +#ifdef CONFIG_PCI +#define CONFIG_SYS_PCI_64BIT +#define CONFIG_PCI_SCAN_SHOW +#endif + +/* MMC */ +#ifdef CONFIG_MMC +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#endif + +/* SATA */ + +#ifdef CONFIG_SCSI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 +#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) +#endif + +/* USB */ +#ifdef CONFIG_USB +#define CONFIG_HAS_FSL_XHCI_USB +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif + +/* FlexSPI */ +#ifdef CONFIG_NXP_FSPI +#define NXP_FSPI_FLASH_SIZE SZ_64M +#define NXP_FSPI_FLASH_NUM 1 +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() +#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4) + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 128 + +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OFFSET 0x500000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_ENV_OFFSET) + +/* Allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_MAXARGS 64 /* max command args */ + +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +/* Initial environment variables */ +#define XSPI_MC_INIT_CMD \ + "env exists secureboot && " \ + "esbc_validate 0x20700000 && " \ + "esbc_validate 0x20740000 ;" \ + "fsl_mc start mc 0x20a00000 0x20e00000\0" + +#define SD_MC_INIT_CMD \ + "mmc read 0x80000000 0x5000 0x800;" \ + "mmc read 0x80100000 0x7000 0x800;" \ + "env exists secureboot && " \ + "mmc read 0x80700000 0x3800 0x10 && " \ + "mmc read 0x80740000 0x3A00 0x10 && " \ + "esbc_validate 0x80700000 && " \ + "esbc_validate 0x80740000 ;" \ + "fsl_mc start mc 0x80000000 0x80100000\0" + +#define EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xa0000000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "fdt_addr=0x64f00000\0" \ + "kernel_start=0x1000000\0" \ + "kernelheader_start=0x7C0000\0" \ + "scriptaddr=0x80000000\0" \ + "scripthdraddr=0x80080000\0" \ + "fdtheader_addr_r=0x80100000\0" \ + "kernelheader_addr_r=0x80200000\0" \ + "kernel_addr_r=0x81000000\0" \ + "kernelheader_size=0x40000\0" \ + "fdt_addr_r=0x90000000\0" \ + "load_addr=0xa0000000\0" \ + "kernel_size=0x2800000\0" \ + "kernel_addr_sd=0x8000\0" \ + "kernelhdr_addr_sd=0x3E00\0" \ + "kernel_size_sd=0x1d000\0" \ + "kernelhdr_size_sd=0x10\0" \ + "console=ttyAMA0,38400n8\0" \ + BOOTENV \ + "mcmemsize=0x70000000\0" \ + XSPI_MC_INIT_CMD \ + "boot_scripts=lx2160ardb_boot.scr\0" \ + "boot_script_hdr=hdr_lx2160ardb_bs.out\0" \ + "scan_dev_for_boot_part=" \ + "part list ${devtype} ${devnum} devplist; " \ + "env exists devplist || setenv devplist 1; " \ + "for distro_bootpart in ${devplist}; do " \ + "if fstype ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "bootfstype; then " \ + "run scan_dev_for_boot; " \ + "fi; " \ + "done\0" \ + "scan_dev_for_boot=" \ + "echo Scanning ${devtype} " \ + "${devnum}:${distro_bootpart}...; " \ + "for prefix in ${boot_prefixes}; do " \ + "run scan_dev_for_scripts; " \ + "done;\0" \ + "boot_a_script=" \ + "load ${devtype} ${devnum}:${distro_bootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "env exists secureboot && load ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "${scripthdraddr} ${prefix}${boot_script_hdr} " \ + "&& esbc_validate ${scripthdraddr};" \ + "source ${scriptaddr}\0" + +#define XSPI_NOR_BOOTCOMMAND \ + "env exists mcinitcmd && env exists secureboot "\ + "&& esbc_validate 0x20780000; " \ + "env exists mcinitcmd && " \ + "fsl_mc lazyapply dpl 0x20d00000; " \ + "run distro_bootcmd;run xspi_bootcmd; " \ + "env exists secureboot && esbc_halt;" + +#define SD_BOOTCOMMAND \ + "env exists mcinitcmd && mmcinfo; " \ + "mmc read 0x80001000 0x6800 0x800; " \ + "env exists mcinitcmd && env exists secureboot " \ + " && mmc read 0x80780000 0x3C00 0x10 " \ + "&& esbc_validate 0x80780000;env exists mcinitcmd " \ + "&& fsl_mc lazyapply dpl 0x80001000;" \ + "run distro_bootcmd;run sd_bootcmd;" \ + "env exists secureboot && esbc_halt;" + +#define BOOT_TARGET_DEVICES(func) \ + func(USB, usb, 0) \ + func(MMC, mmc, 0) \ + func(SCSI, scsi, 0) +#include <config_distro_bootcmd.h> + +#endif /* __LX2_COMMON_H */ |