summaryrefslogtreecommitdiff
path: root/include/configs/mcu25.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/mcu25.h')
-rw-r--r--include/configs/mcu25.h176
1 files changed, 88 insertions, 88 deletions
diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h
index 80011eb044..e4489696b2 100644
--- a/include/configs/mcu25.h
+++ b/include/configs/mcu25.h
@@ -45,46 +45,46 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
/* ... with on-chip memory here (4KBytes) */
-#define CFG_OCM_DATA_ADDR 0xF4000000
-#define CFG_OCM_DATA_SIZE 0x00001000
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
/* Do not set up locked dcache as init ram. */
-#undef CFG_INIT_DCACHE_CS
+#undef CONFIG_SYS_INIT_DCACHE_CS
/* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* OCM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* OCM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
/*
- * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
* The Linux BASE_BAUD define should match this configuration.
* baseBaud = cpuClock/(uartDivisor*16)
- * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
#define CONFIG_SERIAL_MULTI 1
/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */
-#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD 691200
+#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD 691200
/* Size (bytes) of interrupt driven serial port buffer.
* Set to 0 to use polling instead of interrupts.
@@ -96,7 +96,7 @@
#define CONFIG_BAUDRATE 9600
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
@@ -104,18 +104,18 @@
*----------------------------------------------------------------------*/
/* Use common CFI driver */
-#define CFG_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
/* board provides its own flash_init code */
#define CONFIG_FLASH_CFI_LEGACY 1
-#define CFG_FLASH_CFI_WIDTH FLASH_CFI_8BIT
-#define CFG_FLASH_LEGACY_512Kx8 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
/* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
/*-----------------------------------------------------------------------
* Environment
@@ -135,7 +135,7 @@
#ifdef CONFIG_ENV_IS_IN_FLASH
/* Put the environment in Flash */
#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
/* Address and size of Redundant Environment Sector */
@@ -147,22 +147,22 @@
* I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
* the first internal I2C controller of the PPC440EPx
*----------------------------------------------------------------------*/
-#define CFG_SPD_BUS_NUM 0
+#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/* This is the 7bit address of the device, not including P. */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CFG_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+#undef CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_PREBOOT "echo;" \
@@ -178,7 +178,7 @@
#define CONFIG_OVERWRITE_ETHADDR_ONCE
#define CONFIG_SERVERIP 172.25.1.3
-#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
@@ -208,7 +208,7 @@
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
@@ -216,7 +216,7 @@
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descr */
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descr */
/*
* BOOTP options
@@ -252,42 +252,42 @@
#define SPD_EEPROM_ADDRESS 0x50
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_UART | \
- CFG_POST_I2C | \
- CFG_POST_CACHE | \
- CFG_POST_ETHER | \
- CFG_POST_SPR)
-
-#define CFG_POST_UART_TABLE {UART0_BASE}
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_SPR)
+
+#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE}
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
#undef CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
@@ -297,55 +297,55 @@
* External Bus Controller (EBC) Setup
*/
-#define CFG_EBC_CFG 0x98400000
+#define CONFIG_SYS_EBC_CFG 0x98400000
/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CFG_EBC_PB0AP 0x02005400
-#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit*/
+#define CONFIG_SYS_EBC_PB0AP 0x02005400
+#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit*/
-#define CFG_EBC_PB1AP 0x03041200
-#define CFG_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */
+#define CONFIG_SYS_EBC_PB1AP 0x03041200
+#define CONFIG_SYS_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CFG_EBC_PB2AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CFG_EBC_PB2CR 0x7A09A000u
+#define CONFIG_SYS_EBC_PB2AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
+#define CONFIG_SYS_EBC_PB2CR 0x7A09A000u
-#define CFG_EBC_PB3AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CFG_EBC_PB3CR 0x7B09A000u
+#define CONFIG_SYS_EBC_PB3AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
+#define CONFIG_SYS_EBC_PB3CR 0x7B09A000u
-#define CFG_EBC_PB4AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
-#define CFG_EBC_PB4CR 0x7C09A000u
+#define CONFIG_SYS_EBC_PB4AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */
+#define CONFIG_SYS_EBC_PB4CR 0x7C09A000u
-#define CFG_EBC_PB5AP 0x00800200u
-#define CFG_EBC_PB5CR 0x7D81A000u
+#define CONFIG_SYS_EBC_PB5AP 0x00800200u
+#define CONFIG_SYS_EBC_PB5CR 0x7D81A000u
-#define CFG_EBC_PB6AP 0x01040200u
-#define CFG_EBC_PB6CR 0x7D91A000u
+#define CONFIG_SYS_EBC_PB6AP 0x01040200u
+#define CONFIG_SYS_EBC_PB6CR 0x7D91A000u
-#define CFG_GPIO0_OR 0x087FFFFF /* GPIO value */
-#define CFG_GPIO0_TCR 0x7FFF8000 /* GPIO value */
-#define CFG_GPIO0_ODR 0xFFFF0000 /* GPIO value */
+#define CONFIG_SYS_GPIO0_OR 0x087FFFFF /* GPIO value */
+#define CONFIG_SYS_GPIO0_TCR 0x7FFF8000 /* GPIO value */
+#define CONFIG_SYS_GPIO0_ODR 0xFFFF0000 /* GPIO value */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF0000500
-#define CFG_HUSH_PARSER /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)