diff options
Diffstat (limited to 'include/configs/pdm360ng.h')
| -rw-r--r-- | include/configs/pdm360ng.h | 420 |
1 files changed, 0 insertions, 420 deletions
diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h deleted file mode 100644 index 676d55f5e8..0000000000 --- a/include/configs/pdm360ng.h +++ /dev/null @@ -1,420 +0,0 @@ -/* - * (C) Copyright 2009-2010 - * Michael Weiß, ifm ecomatic gmbh, michael.weiss@ifm.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * pdm360ng board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PDM360NG 1 - -/* - * Memory map for the PDM360NG board: - * - * 0x0000_0000 - 0x1FFF_FFFF DDR RAM (512 MB) - * 0x2000_0000 - 0x3FFF_FFFF reserved (DDR RAM (512 MB) - * 0x5000_0000 - 0x5001_FFFF SRAM (128 KB) - * 0x5004_0000 - 0x5005_FFFF MRAM (CS2) (128 KB) - * 0x8000_0000 - 0x803F_FFFF IMMR (4 MB) - * 0xF000_0000 - 0xF7FF_FFFF NOR FLASH (CS0) (128 MB) - * 0xF800_0000 - 0xFFFF_FFFF NOR FLASH (CS1) (128 MB) optional - */ - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ -#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ - -#define CONFIG_SYS_TEXT_BASE 0xF0000000 - -/* Used for silent command in environment */ -#define CONFIG_SYS_DEVICE_NULLDEV - -/* Video */ - -#if defined(CONFIG_VIDEO) -#define CONFIG_SPLASH_SCREEN -#define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_BMP_RLE8 -#endif - -#define CONFIG_SYS_MPC512X_CLKIN 33333333 /* in Hz */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_IMMR 0x80000000 -#define CONFIG_SYS_DIU_ADDR ((CONFIG_SYS_IMMR) + 0x2100) - -/* - * DDR Setup - */ - -/* DDR is system memory */ -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_MAX_RAM_SIZE 0x40000000 - -/* DDR pin mux and slew rate */ -#define CONFIG_SYS_IOCTRL_MUX_DDR 0x00000012 - -/* Manually set all parameters as there's no SPD etc. */ -/* - * DDR Controller Configuration for Micron DDR2 SDRAM MT47H128M8-3 - * - * SYS_CFG: - * [31:31] MDDRC Soft Reset: Diabled - * [30:30] DRAM CKE pin: Enabled - * [29:29] DRAM CLK: Enabled - * [28:28] Command Mode: Enabled (For initialization only) - * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] - * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] - * [20:19] Read Test: DON'T USE - * [18:18] Self Refresh: Enabled - * [17:17] 16bit Mode: Disabled - * [16:13] Read Delay: 3 - * [12:12] Half DQS Delay: Disabled - * [11:11] Quarter DQS Delay: Disabled - * [10:08] Write Delay: 2 - * [07:07] Early ODT: Disabled - * [06:06] On DIE Termination: Enabled - * [05:05] FIFO Overflow Clear: DON'T USE here - * [04:04] FIFO Underflow Clear: DON'T USE here - * [03:03] FIFO Overflow Pending: DON'T USE here - * [02:02] FIFO Underlfow Pending: DON'T USE here - * [01:01] FIFO Overlfow Enabled: Enabled - * [00:00] FIFO Underflow Enabled: Enabled - * TIME_CFG0 - * [31:16] DRAM Refresh Time: 0 CSB clocks - * [15:8] DRAM Command Time: 0 CSB clocks - * [07:00] DRAM Precharge Time: 0 CSB clocks - * TIME_CFG1 - * [31:26] DRAM tRFC: - * [25:21] DRAM tWR1: - * [20:17] DRAM tWRT1: - * [16:11] DRAM tDRR: - * [10:05] DRAM tRC: - * [04:00] DRAM tRAS: - * TIME_CFG2 - * [31:28] DRAM tRCD: - * [27:23] DRAM tFAW: - * [22:19] DRAM tRTW1: - * [18:15] DRAM tCCD: - * [14:10] DRAM tRTP: - * [09:05] DRAM tRP: - * [04:00] DRAM tRPA - */ -#define CONFIG_SYS_MDDRC_SYS_CFG 0xEA804A40 -#define CONFIG_SYS_MDDRC_TIME_CFG0 0x030C3D2E -#define CONFIG_SYS_MDDRC_TIME_CFG1 0x68EC1168 -#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34310864 - -/* - * Alternative 1: small RAM (128 MB) configuration - */ -#define CONFIG_SYS_MDDRC_SYS_CFG_ALT1 0xE8604A40 -#define CONFIG_SYS_MDDRC_TIME_CFG0_ALT1 0x030C3D2E -#define CONFIG_SYS_MDDRC_TIME_CFG1_ALT1 0x3CEC1168 -#define CONFIG_SYS_MDDRC_TIME_CFG2_ALT1 0x33310863 - -#define CONFIG_SYS_MDDRC_SYS_CFG_EN 0xF0000000 - -#define CONFIG_SYS_DDRCMD_NOP 0x01380000 -#define CONFIG_SYS_DDRCMD_PCHG_ALL 0x01100400 -#define CONFIG_SYS_DDRCMD_EM2 0x01020000 /* EMR2 */ -#define CONFIG_SYS_DDRCMD_EM3 0x01030000 /* EMR3 */ -/* EMR with 150 ohm ODT todo: verify */ -#define CONFIG_SYS_DDRCMD_EN_DLL 0x01010040 -#define CONFIG_SYS_DDRCMD_RES_DLL 0x01000100 -#define CONFIG_SYS_DDRCMD_RFSH 0x01080000 -#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 -/* EMR with 150 ohm ODT todo: verify */ -#define CONFIG_SYS_DDRCMD_OCD_DEFAULT 0x010107C0 -/* EMR new command with 150 ohm ODT todo: verify */ -#define CONFIG_SYS_DDRCMD_OCD_EXIT 0x01010440 - -/* DDR Priority Manager Configuration */ -#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 -#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 -#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 -#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC -#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA -#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 -#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 -#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 - -/* - * NOR FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE - -#define CONFIG_SYS_FLASH_BASE 0xF0000000 /* start of FLASH-Bank0 */ -#define CONFIG_SYS_FLASH_SIZE 0x08000000 /* max size of a Bank */ -/* start of FLASH-Bank1 */ -#define CONFIG_SYS_FLASH1_BASE (CONFIG_SYS_FLASH_BASE + \ - CONFIG_SYS_FLASH_SIZE) -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST \ - {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH1_BASE} - -#define CONFIG_SYS_SRAM_BASE 0x50000000 -#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ - -#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH1_BASE -#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE - -/* ALE active low, data size 4 bytes */ -#define CONFIG_SYS_CS0_CFG 0x05059350 -/* ALE active low, data size 4 bytes */ -#define CONFIG_SYS_CS1_CFG 0x05059350 - -#define CONFIG_SYS_MRAM_BASE 0x50040000 -#define CONFIG_SYS_MRAM_SIZE 0x00020000 -#define CONFIG_SYS_CS2_START CONFIG_SYS_MRAM_BASE -#define CONFIG_SYS_CS2_SIZE CONFIG_SYS_MRAM_SIZE - -/* ALE active low, data size 4 bytes */ -#define CONFIG_SYS_CS2_CFG 0x05059110 - -/* alt. CS timing for CS0, CS1, CS2 */ -#define CONFIG_SYS_CS_ALETIMING 0x00000007 - -/* - * NAND FLASH - */ -#define CONFIG_CMD_NAND /* enable NAND support */ -#define CONFIG_NAND_MPC5121_NFC -#define CONFIG_SYS_NAND_BASE 0x40000000 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_SELECT_DEVICE /* driver supports mutipl. chips */ - -/* - * Configuration parameters for MPC5121 NAND driver - */ -#define CONFIG_FSL_NFC_WIDTH 1 -#define CONFIG_FSL_NFC_WRITE_SIZE 2048 -#define CONFIG_FSL_NFC_SPARE_SIZE 64 -#define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE - -/* - * Dynamic MTD partition support - */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=f0000000.flash,nor1=f8000000.flash," \ - "nand0=MPC5121 NAND" - -/* - * Flash layout - */ -#define MTDPARTS_DEFAULT "mtdparts=f0000000.flash:512k(u-boot)," \ - "256k(environment1)," \ - "256k(environment2)," \ - "256k(splash-factory)," \ - "2m(FIT: recovery)," \ - "4608k(fs-recovery)," \ - "256k(splash-customer),"\ - "5m(FIT: kernel+dtb)," \ - "64m(rootfs squash)ro," \ - "51m(userfs ubi);" \ - "f8000000.flash:-(unused);" \ - "MPC5121 NAND:1024m(extended-userfs)" - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of monitor */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* 512 kB for monitor */ -#ifdef CONFIG_FSL_DIU_FB -#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* for malloc */ -#else -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) -#endif - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 6 /* console is on PSC6 */ -#if CONFIG_PSC_CONSOLE != 6 -#error CONFIG_PSC_CONSOLE must be 6 -#endif - -#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC6_TX_SIZE -#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC6_TX_ADDR -#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC6_RX_SIZE -#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC6_RX_ADDR - -/* - * Clocks in use - */ -#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \ - CLOCK_SCCR1_LPC_EN | \ - CLOCK_SCCR1_NFC_EN | \ - CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \ - CLOCK_SCCR1_PSCFIFO_EN | \ - CLOCK_SCCR1_DDR_EN | \ - CLOCK_SCCR1_FEC_EN | \ - CLOCK_SCCR1_TPR_EN) - -#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \ - CLOCK_SCCR2_SPDIF_EN | \ - CLOCK_SCCR2_DIU_EN | \ - CLOCK_SCCR2_I2C_EN) - -/* - * Used PSC UART devices - */ -#define CONFIG_SYS_PSC1 -#define CONFIG_SYS_PSC4 -#define CONFIG_SYS_PSC6 - -/* - * Co-processor communication parameters - */ -#define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000 -#define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400 - -/* - * IIM - IC Identification Module - */ -#undef CONFIG_FSL_IIM - -/* - * Enabled only to delete "ethaddr" before testing - * "ethaddr" setting from EEPROM - */ -#define CONFIG_ENV_OVERWRITE - -/* - * Ethernet configuration - */ -#define CONFIG_MPC512x_FEC 1 -#define CONFIG_PHY_ADDR 0x1F -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_FEC_AN_TIMEOUT 1 -#define CONFIG_HAS_ETH0 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -/* This has to be a multiple of the Flash sector size */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_CMD_REGINFO - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#ifdef CONFIG_CMD_KGDB - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -/* Max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -/* Decrementer freq: 1ms ticks */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -/* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -/* Cache Configuration */ -#define CONFIG_SYS_DCACHE_SIZE 32768 -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -/* log base 2 of the above value */ -#define CONFIG_SYS_CACHELINE_SHIFT 5 -#endif - -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | HID0_ICE) -#define CONFIG_SYS_HID2 HID2_HBE - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_COPROC) - -/* - * Environment Configuration - */ -#define CONFIG_TIMESTAMP - -#define CONFIG_HOSTNAME pdm360ng -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 400000 - - -#define CONFIG_PREBOOT "echo;" \ - "echo PDM360NG SAMPLE;" \ - "echo" - -#define CONFIG_BOOTCOMMAND "run env_cont" - -#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1 - -#define OF_CPU "PowerPC,5121@0" -#define OF_SOC_COMPAT "fsl,mpc5121-immr" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc@80000000/serial@11600" - -/* - * Include common options for all mpc5121 boards - */ -#include "mpc5121-common.h" - -#endif /* __CONFIG_H */ |