diff options
Diffstat (limited to 'include/configs/stamp9g20.h')
| -rw-r--r-- | include/configs/stamp9g20.h | 244 |
1 files changed, 0 insertions, 244 deletions
diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h deleted file mode 100644 index 87df70bdac..0000000000 --- a/include/configs/stamp9g20.h +++ /dev/null @@ -1,244 +0,0 @@ -/* - * (C) Copyright 2007-2008 - * Stelian Pop <stelian@popies.net> - * Lead Tech Design <www.leadtechdesign.com> - * - * (C) Copyright 2010 - * Achim Ehrlich <aehrlich@taskit.de> - * taskit GmbH <www.taskit.de> - * - * (C) Copyright 2012 - * Markus Hubig <mhubig@imko.de> - * IMKO GmbH <www.imko.de> - * - * Configuation settings for the stamp9g20 CPU module. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * SoC must be defined first, before hardware.h is included. - * In this case SoC is defined in boards.cfg. - */ -#include <asm/hardware.h> - -/* - * Warning: changing CONFIG_SYS_TEXT_BASE requires adapting the initial boot - * program. Since the linker has to swallow that define, we must use a pure - * hex number here! - */ -#define CONFIG_SYS_TEXT_BASE 0x23f00000 - -/* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432MHz crystal */ - -/* misc settings */ -#define CONFIG_CMDLINE_TAG /* pass commandline to Kernel */ -#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */ -#define CONFIG_INITRD_TAG /* pass initrd param to kernel */ -#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ -#define CONFIG_BOARD_EARLY_INIT_f /* call board_early_init_f() */ -#define CONFIG_BOARD_POSTCLK_INIT /* call board_postclk_init() */ -#define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */ - -/* setting board specific options */ -#ifdef CONFIG_PORTUXG20 -# define CONFIG_MACH_TYPE MACH_TYPE_PORTUXG20 -# define CONFIG_MACB -#else -# define CONFIG_MACH_TYPE MACH_TYPE_STAMP9G20 -#endif - -/* - * SDRAM: 1 bank, 64 MB, base address 0x20000000 - * Already initialized before u-boot gets started. - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 -#define CONFIG_SYS_SDRAM_SIZE (64 << 20) - -/* - * Perform a SDRAM Memtest from the start of SDRAM - * till the beginning of the U-Boot position in RAM. - */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000) - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN \ - ROUND(3 * CONFIG_ENV_SIZE + (128 << 10), 0x1000) - -/* - * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, - * leaving the correct space for initial global data structure above that - * address while providing maximum stack area below. - */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) - -/* NAND flash settings */ -#define CONFIG_NAND_ATMEL -#define CONFIG_SYS_NO_FLASH -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 -#define CONFIG_SYS_NAND_DBW_8 -#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) -#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 - -/* general purpose I/O */ -#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ -#define CONFIG_AT91_GPIO /* enable the GPIO features */ -#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ - -/* serial console */ -#define CONFIG_ATMEL_USART -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS -#define CONFIG_BAUDRATE 115200 - -/* LED configuration */ -#define CONFIG_STATUS_LED -#define CONFIG_BOARD_SPECIFIC_LED - -/* The LED PINs */ -#define CONFIG_RED_LED AT91_PIN_PC5 -#define CONFIG_GREEN_LED AT91_PIN_PC4 -#define CONFIG_YELLOW_LED AT91_PIN_PC10 - -#define STATUS_LED_RED 0 -#define STATUS_LED_GREEN 1 -#define STATUS_LED_YELLOW 2 - -/* Red LED */ -#define STATUS_LED_BIT STATUS_LED_RED -#define STATUS_LED_STATE STATUS_LED_OFF -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) - -/* Green LED */ -#define STATUS_LED_BIT1 STATUS_LED_GREEN -#define STATUS_LED_STATE1 STATUS_LED_ON -#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) - -/* Yellow LED */ -#define STATUS_LED_BIT2 STATUS_LED_YELLOW -#define STATUS_LED_STATE2 STATUS_LED_OFF -#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2) - -/* Boot status LED */ -#define STATUS_LED_BOOT STATUS_LED_GREEN - -/* - * Ethernet configuration - * - * PortuxG20 has always ethernet but for Stamp9G20 you - * can enable it here if your baseboard features ethernet. - */ - -#define CONFIG_MACB -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_USB_ETHER_MCS7830 - -#ifdef CONFIG_MACB -# define CONFIG_RMII /* use reduced MII inteface */ -# define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */ -#define CONFIG_AT91_WANTS_COMMON_PHY - -/* BOOTP and DHCP options */ -# define CONFIG_BOOTP_BOOTFILESIZE -# define CONFIG_BOOTP_BOOTPATH -# define CONFIG_BOOTP_GATEWAY -# define CONFIG_BOOTP_HOSTNAME -# define CONFIG_NFSBOOTCOMMAND \ - "setenv autoload yes; setenv autoboot yes; " \ - "setenv bootargs ${basicargs} ${mtdparts} " \ - "root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; " \ - "dhcp" -#endif /* CONFIG_MACB */ - -/* Enable the watchdog */ -#define CONFIG_AT91SAM9_WATCHDOG -#define CONFIG_HW_WATCHDOG - -/* USB configuration */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB -#define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_SYS_USB_OHCI_CPU_INIT -#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 - -/* General Boot Parameter */ -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTCOMMAND "run flashboot" -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING - -/* - * RAM Memory address where to put the - * Linux Kernel befor starting. - */ -#define CONFIG_SYS_LOAD_ADDR 0x22000000 - -/* - * The NAND Flash partitions: - * ========================================== - * 0x0000000-0x001ffff -> 128k, bootstrap - * 0x0020000-0x005ffff -> 256k, u-boot - * 0x0060000-0x007ffff -> 128k, env1 - * 0x0080000-0x009ffff -> 128k, env2 (backup) - * 0x0100000-0x06fffff -> 6M, kernel - * 0x0700000-0x8000000 -> 121M, RootFS - */ -#define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_OFFSET ((128 + 256) << 10) -#define CONFIG_ENV_OFFSET_REDUND ((128 + 256 + 128) << 10) -#define CONFIG_ENV_SIZE (128 << 10) - -/* - * Predefined environment variables. - * Usefull to define some easy to use boot commands. - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - \ - "basicargs=console=ttyS0,115200\0" \ - \ - "mtdparts=mtdparts=atmel_nand:128k(bootstrap)ro," \ - "256k(uboot)ro,128k(env1)ro," \ - "128k(env2)ro,6M(linux),-(root)rw\0" \ - \ - "flashboot=setenv bootargs ${basicargs} ${mtdparts} " \ - "root=/dev/mtdblock5 rootfstype=jffs2; " \ - "nand read 0x22000000 0x100000 0x600000; " \ - "bootm 22000000\0" \ - \ - "sdboot=setenv bootargs ${basicargs} ${mtdparts} " \ - "root=/dev/mmcblk0p1 rootwait; " \ - "nand read 0x22000000 0x100000 0x600000; " \ - "bootm 22000000" - -/* Command line & features configuration */ -#define CONFIG_CMD_NAND -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_CMD_LED - -#ifdef CONFIG_MACB -# define CONFIG_CMD_PING -# define CONFIG_CMD_DHCP -#endif /* CONFIG_MACB */ - -#endif /* __CONFIG_H */ |