diff options
Diffstat (limited to 'include/configs/topic_miami.h')
| -rw-r--r-- | include/configs/topic_miami.h | 149 |
1 files changed, 149 insertions, 0 deletions
diff --git a/include/configs/topic_miami.h b/include/configs/topic_miami.h new file mode 100644 index 0000000000..3b0fa29890 --- /dev/null +++ b/include/configs/topic_miami.h @@ -0,0 +1,149 @@ +/* + * (C) Copyright 2014 Topic Embedded Products + * + * Configuration for Zynq Evaluation and Development Board - Miami + * See zynq-common.h for Zynq common configs + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_TOPIC_MIAMI_H +#define __CONFIG_TOPIC_MIAMI_H + +#define CONFIG_ZYNQ_PS_CLK_FREQ 33333333UL + +#define CONFIG_ZYNQ_I2C0 +#define CONFIG_ZYNQ_I2C1 + +/* Speed up boot time by ignoring the environment which we never used */ +#define CONFIG_ENV_IS_NOWHERE + +#include "zynq-common.h" + +/* Fixup settings */ +#undef CONFIG_ENV_SIZE +#define CONFIG_ENV_SIZE 0x8000 +#undef CONFIG_ENV_OFFSET +#define CONFIG_ENV_OFFSET 0x80000 + +/* SPL settings */ +#undef CONFIG_SPL_ETH_SUPPORT +#undef CONFIG_SYS_SPI_U_BOOT_OFFS +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#undef CONFIG_SPL_MAX_FOOTPRINT +#define CONFIG_SPL_MAX_FOOTPRINT CONFIG_SYS_SPI_U_BOOT_OFFS +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" + +/* sspi command isn't useful */ +#undef CONFIG_CMD_SPI + +/* No useful gpio */ +#undef CONFIG_ZYNQ_GPIO +#undef CONFIG_CMD_GPIO + +/* No falcon support */ +#undef CONFIG_SPL_OS_BOOT +#undef CONFIG_SPL_FPGA_SUPPORT + +/* FPGA commands that we don't use */ +#undef CONFIG_CMD_FPGA_LOADMK +#undef CONFIG_CMD_FPGA_LOADP +#undef CONFIG_CMD_FPGA_LOADBP +#undef CONFIG_CMD_FPGA_LOADFS + +/* Extras */ +#define CONFIG_CMD_MEMTEST +#undef CONFIG_SYS_MEMTEST_START +#define CONFIG_SYS_MEMTEST_START 0 +#undef CONFIG_SYS_MEMTEST_END +#define CONFIG_SYS_MEMTEST_END 0x18000000 + +/* Faster flash, ours may run at 108 MHz */ +#undef CONFIG_SF_DEFAULT_SPEED +#define CONFIG_SF_DEFAULT_SPEED 108000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#undef CONFIG_SF_DUAL_FLASH +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#undef CONFIG_SPI_FLASH_WINBOND +#undef CONFIG_SPI_FLASH_ISSI + +/* Setup proper boot sequences for Miami boards */ + +#if defined(CONFIG_USB) +# define EXTRA_ENV_USB \ + "usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\ + "i2c mw 41 1 fe && i2c mw 41 1 ff\0" \ + "usbboot=run usbreset && if usb start; then " \ + "echo Booting from USB... && " \ + "if load usb 0 0x1900000 ${bootscript}; then "\ + "source 0x1900000; fi; " \ + "load usb 0 ${kernel_addr} ${kernel_image} && " \ + "load usb 0 ${devicetree_addr} ${devicetree_image} && " \ + "load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \ + "bootm ${kernel_addr} ${ramdisk_load_address} "\ + "${devicetree_addr}; " \ + "fi\0" + /* Note that addresses here should match the addresses in the env */ +# undef DFU_ALT_INFO +# define DFU_ALT_INFO \ + "dfu_alt_info=" \ + "uImage ram 0x2080000 0x500000;" \ + "devicetree.dtb ram 0x2000000 0x20000;" \ + "uramdisk.image.gz ram 0x4000000 0x10000000\0" \ + "dfu_ram=run usbreset && dfu 0 ram 0\0" \ + "thor_ram=run usbreset && thordown 0 ram 0\0" +#else +# define EXTRA_ENV_USB +#endif + +#undef CONFIG_PREBOOT + +#undef CONFIG_EXTRA_ENV_SETTINGS +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernel_image=uImage\0" \ + "kernel_addr=0x2080000\0" \ + "ramdisk_image=uramdisk.image.gz\0" \ + "ramdisk_load_address=0x4000000\0" \ + "devicetree_image=devicetree.dtb\0" \ + "devicetree_addr=0x2000000\0" \ + "bitstream_image=fpga.bin\0" \ + "bootscript=autorun.scr\0" \ + "loadbit_addr=0x100000\0" \ + "loadbootenv_addr=0x2000000\0" \ + "kernel_size=0x400000\0" \ + "devicetree_size=0x10000\0" \ + "boot_size=0xF00000\0" \ + "fdt_high=0x20000000\0" \ + "initrd_high=0x20000000\0" \ + "mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \ + "mmcinfo && " \ + "load mmc 0 ${loadbit_addr} ${bitstream_image} && " \ + "fpga load 0 ${loadbit_addr} ${filesize}\0" \ + "qspiboot=echo Booting from QSPI flash... && " \ + "sf probe && " \ + "sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \ + "sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \ + "bootm ${kernel_addr} - ${devicetree_addr}\0" \ + "sdboot=if mmcinfo; then " \ + "setenv bootargs console=ttyPS0,115200 " \ + "root=/dev/mmcblk0p2 rw rootfstype=ext4 " \ + "rootwait quiet ; " \ + "load mmc 0 ${kernel_addr} ${kernel_image}&& " \ + "load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \ + "bootm ${kernel_addr} - ${devicetree_addr}; " \ + "fi\0" \ + EXTRA_ENV_USB \ + DFU_ALT_INFO + +#undef CONFIG_BOOTCOMMAND +#define CONFIG_BOOTCOMMAND "if mmcinfo; then " \ + "if fatload mmc 0 0x1900000 ${bootscript}; then source 0x1900000; " \ + "fi; fi; run $modeboot" +#undef CONFIG_DISPLAY_BOARDINFO + +/* Further tweaks to reduce image size */ +#undef CONFIG_CMD_BOOTZ +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_AES + +#endif /* __CONFIG_TOPIC_MIAMI_H */ |