diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/acadia.h | 424 |
1 files changed, 424 insertions, 0 deletions
diff --git a/include/configs/acadia.h b/include/configs/acadia.h new file mode 100644 index 0000000000..9e02ca31b4 --- /dev/null +++ b/include/configs/acadia.h @@ -0,0 +1,424 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * acadia.h - configuration for AMCC Acadia (405EZ) + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_ACADIA 1 /* Board is Acadia */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_405EZ 1 /* Specifc 405EZ support*/ +#undef CFG_DRAM_TEST /* Disable-takes long time */ +#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ + +#define CONFIG_NO_SERIAL_EEPROM +/*#undef CONFIG_NO_SERIAL_EEPROM*/ + +#ifdef CONFIG_NO_SERIAL_EEPROM + +/*---------------------------------------------------------------------------- + * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, + * assuming a 66MHz input clock to the 405EZ. + *---------------------------------------------------------------------------*/ +/* #define PLLMR0_100_100_12 */ +#define PLLMR0_200_133_66 +/* #define PLLMR0_266_160_80 */ +/* #define PLLMR0_333_166_83 */ +#endif + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFE000000 +#define CFG_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (384 * 1024)/* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */ + +/* + * Define here the location of the environment variables (FLASH). + * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only + * supported for backward compatibility. + */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) + #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else + #define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#endif + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=acadia\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=acadia/uImage\0" \ + "kernel_addr=fff10000\0" \ + "ramdisk_addr=fff20000\0" \ + "initrd_high=30000000\0" \ + "load=tftp 200000 acadia/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b ${fileaddr} fffc0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "kozio=bootm ffc60000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_NET_MULTI 1 +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +#if 0 /* test-only */ +#define TEST_ONLY_NAND +#endif + +#ifdef TEST_ONLY_NAND +#define CMD_NAND CFG_CMD_NAND +#else +#define CMD_NAND 0 +#endif + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +#define CONFIG_SUPPORT_VFAT + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DTT | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CMD_NAND | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM | \ + CFG_CMD_USB) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#define CFG_BASE_BAUD 691200 +#define CONFIG_BAUDRATE 115200 + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0xa8>>1) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_AD7414 1 /* use AD7414 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#if 0 /* test-only... */ +/*----------------------------------------------------------------------- + * SPI stuff - Define to include SPI control + *----------------------------------------------------------------------- + */ +#define CONFIG_SPI +#endif + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif + +#ifdef TEST_ONLY_NAND +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE (CFG_NAND + CFG_NAND_CS) +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EZ CPU */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/ +#endif + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CFG_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */ +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SRAM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* size for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ +#define CFG_NAND 0xd0000000 +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ + +/* Memory Bank 0 (Flash) initialization */ +#define CFG_EBC_PB0AP 0x03337200 +#define CFG_EBC_PB0CR 0xfe0bc000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=32bit */ + +/* Memory Bank 1 (CRAM) initialization */ +#define CFG_EBC_PB1AP 0x030400c0 +#define CFG_EBC_PB1CR 0x000bc000 + +/* Memory Bank 2 (CRAM) initialization */ +#define CFG_EBC_PB2AP 0x030400c0 +#define CFG_EBC_PB2CR 0x020bc000 + +/* Memory Bank 3 (NAND-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x018003c0 +#define CFG_EBC_PB3CR (CFG_NAND | 0x1c000) + +/* Memory Bank 4 (CPLD) initialization */ +#define CFG_EBC_PB4AP 0x04006000 +#define CFG_EBC_PB4CR 0x80018000 /* BAS=0x000,BS=16MB,BU=R/W,BW=32bit */ + +#define CFG_EBC_CFG 0xf8400000 + +/*----------------------------------------------------------------------- + * Definitions for GPIO_0 setup (PPC405EZ specific) + * + * GPIO0[0-3] - External Bus Controller CS_4 - CS_7 Outputs + * GPIO0[4] - External Bus Controller Hold Input + * GPIO0[5] - External Bus Controller Priority Input + * GPIO0[6] - External Bus Controller HLDA Output + * GPIO0[7] - External Bus Controller Bus Request Output + * GPIO0[8] - CRAM Clk Output + * GPIO0[9] - External Bus Controller Ready Input + * GPIO0[10] - CRAM Adv Output + * GPIO0[11-24] - NAND Flash Control Data -> Bypasses GPIO when enabled + * GPIO0[25] - External DMA Request Input + * GPIO0[26] - External DMA EOT I/O + * GPIO0[25] - External DMA Ack_n Output + * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs + * GPIO0[28-30] - Trace Outputs / PWM Inputs + * GPIO0[31] - PWM_8 I/O + */ +#define CFG_GPIO0_TCR 0xC0000000 +#define CFG_GPIO0_OSRL 0x50000000 +#define CFG_GPIO0_OSRH 0x00000055 +#define CFG_GPIO0_ISR1L 0x00000000 +#define CFG_GPIO0_ISR1H 0x00000055 +#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TSRH 0x00000055 + +/*----------------------------------------------------------------------- + * Definitions for GPIO_1 setup (PPC405EZ specific) + * + * GPIO1[0-6] - PWM_9 to PWM_15 I/O + * GPIO1[7] - PWM_DIV_CLK (Out) / IRQ4 Input + * GPIO1[8] - TS5 Output / DAC_IP_TRIG Input + * GPIO1[9] - TS6 Output / ADC_IP_TRIG Input + * GPIO1[10-12] - UART0 Control Inputs + * GPIO1[13] - UART0_DTR_N Output/IEEE_1588_TS Output/TMRCLK Input + * GPIO1[14] - UART0_RTS_N Output/SPI_SS_2_N Output + * GPIO1[15] - SPI_SS_3_N Output/UART0_RI_N Input + * GPIO1[16] - SPI_SS_1_N Output + * GPIO1[17-20] - Trace Output/External Interrupts IRQ0 - IRQ3 inputs + */ +#define CFG_GPIO1_OSRH 0x55455555 +#define CFG_GPIO1_OSRL 0x40000110 +#define CFG_GPIO1_ISR1H 0x00000000 +#define CFG_GPIO1_ISR1L 0x15555445 +#define CFG_GPIO1_TSRH 0x00000000 +#define CFG_GPIO1_TSRL 0x00000000 +#define CFG_GPIO1_TCR 0xFFFF8014 + +/*----------------------------------------------------------------------- + * EPLD Regs. + */ +#define EPLD_BASE 0x80000000 +#define EPLD_ETHRSTBOOT 0x10 +#define EPLD_CTRL 0x14 +#define EPLD_MUXOE 0x16 + +/* + * State definations + */ +#define LOAK_INIT 0x494e4954 /* ASCII "INIT" */ +#define LOAK_NONE 0x4e4f4e45 /* ASCII "NONE" */ +#define LOAK_CRAM 0x4352414d /* ASCII "CRAM" */ +#define LOAK_PSRAM 0x50535241 /* ASCII "PSRA" - PSRAM */ +#define LOAK_OCM 0x4f434d20 /* ASCII "OCM " */ +#define LOAK_ZERO 0x5a45524f /* ASCII "ZERO" */ +#define LOAK_SPL 0x53504c20 /* ASCII "SPL" */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ + #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#endif /* __CONFIG_H */ |