Merge with /home/wd/git/u-boot/custodian/u-boot-blackfin

6 files changed, 1441 insertions, 521 deletions

diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
new file mode 100644
index 0000000000..65dfc81554
--- /dev/null
+++ b/include/configs/bf533-ezkit.h
@@ -0,0 +1,228 @@
+/*
+ * U-boot - Configuration file for BF533 EZKIT board
+ */
+
+#ifndef __CONFIG_EZKIT533_H__
+#define __CONFIG_EZKIT533_H__
+
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_STAMP		1
+
+#define CONFIG_BOOTDELAY	5
+#define CFG_AUTOLOAD		"no"	/*rarpb, bootp or dhcp commands will perform only a */
+
+#define CFG_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING	1
+#define CONFIG_LOADADDR		0x01000000	/* default load address */
+#define CONFIG_BOOTCOMMAND	"tftp $(loadaddr) linux"
+/* #define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw" */
+
+#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_SMC91111_BASE	0x20310300
+
+#if 0
+#define	CONFIG_MII
+#define CFG_DISCOVER_PHY
+#endif
+
+#define CONFIG_RTC_BFIN		1
+#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
+
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF533_BYPASS_BOOT	0x0001	/* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT		0x0002	/* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT		0x0004	/* Bootmode 3: Boot from SPI flash */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE		BF533_BYPASS_BOOT
+/* #define BFIN_BOOT_MODE	BF533_SPI_BOOT */
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF531		0x31
+#define ADSP_BF532		0x32
+#define ADSP_BF533		0x33
+#define BFIN_CPU		ADSP_BF533
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/* CONFIG_CLKIN_HZ is any value in Hz				*/
+#define CONFIG_CLKIN_HZ		27000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
+/*						    1=CLKIN/2	*/
+#define CONFIG_CLKIN_HALF	0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
+/*						 1=bypass PLL	*/
+#define CONFIG_PLL_BYPASS	0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
+/* Values can range from 1-64					*/
+#define CONFIG_VCO_MULT		22
+/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
+/* Values can be 1, 2, 4, or 8 ONLY				*/
+#define CONFIG_CCLK_DIV		1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
+/* Values can range from 1-15					*/
+#define CONFIG_SCLK_DIV		5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
+/* Values can range from 2-65535				*/
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
+#define CONFIG_SPI_BAUD		2
+#define CONFIG_SPI_BAUD_INITBLOCK	4
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
+#endif
+
+#define CONFIG_MEM_SIZE		32	/* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH	9	/* 8, 9, 10, 11    */
+#define CONFIG_MEM_MT48LC16M16A2TG_75	1
+
+#define CONFIG_LOADS_ECHO	1
+
+
+#define CONFIG_COMMANDS			(CONFIG_CMD_DFL	| \
+					 CFG_CMD_PING	| \
+					 CFG_CMD_ELF	| \
+					 CFG_CMD_I2C	| \
+					 CFG_CMD_JFFS2	| \
+					 CFG_CMD_DATE)
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define	CFG_PROMPT		"ezkit> "	/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+#define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_MEMTEST_START	0x00000000	/* memtest works on */
+#define CFG_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024 * 1024)	/* 1 ... 31 MB in DRAM */
+#define	CFG_LOAD_ADDR		0x01000000	/* default load address */
+#define	CFG_HZ			1000	/* decrementer freq: 10 ms ticks */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 * 1024)
+#define CFG_FLASH_BASE		0x20000000
+
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_SIZE	0x4000
+#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)
+
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_FLASH0_BASE		0x20000000
+#define CFG_FLASH1_BASE		0x20200000
+#define CFG_FLASH2_BASE		0x20280000
+#define CFG_MAX_FLASH_BANKS	3	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	40	/* max number of sectors on one chip */
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		0x20020000
+#define	CFG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */
+
+/* JFFS Partition offset set  */
+#define CFG_JFFS2_FIRST_BANK	0
+#define CFG_JFFS2_NUM_BANKS	1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR	11
+
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+
+#define POLL_MODE		1
+#define FLASH_TOT_SECT		40
+#define FLASH_SIZE		0x220000
+#define CFG_FLASH_SIZE		0x220000
+
+/*
+ * Initialize PSD4256 registers for using I2C
+ */
+#define	CONFIG_MISC_INIT_R
+
+/*
+ * I2C settings
+ * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ */
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged */
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL			PF0
+#define PF_SDA			PF1
+
+#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
+#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit)	if(bit) { \
+				*pFIO_FLAG_S = PF_SDA; \
+				asm("ssync;"); \
+				} \
+			else    { \
+				*pFIO_FLAG_C = PF_SDA; \
+				asm("ssync;"); \
+				}
+#define I2C_SCL(bit)	if(bit) { \
+				*pFIO_FLAG_S = PF_SCL; \
+				asm("ssync;"); \
+				} \
+			else    { \
+				*pFIO_FLAG_C = PF_SCL; \
+				asm("ssync;"); \
+				}
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED		50000
+#define CFG_I2C_SLAVE		0xFE
+
+#define CFG_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */
+
+/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
+/* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
+				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
+#define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
+				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
+*/
+#define AMGCTLVAL		0xFF
+#define AMBCTL0VAL		0x7BB07BB0
+#define AMBCTL1VAL		0xFFC27BB0
+
+#define CONFIG_VDSP		1
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP		0x8
+#define SHT_STRTAB_VDSP		0x1
+#define ELFSHDRSIZE_VDSP	0x2C
+#define VDSP_ENTRY_ADDR		0xFFA00000
+#endif
+
+#endif
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
new file mode 100644
index 0000000000..79a1404a40
--- /dev/null
+++ b/include/configs/bf533-stamp.h
@@ -0,0 +1,467 @@
+/*
+ * U-boot - Configuration file for BF533 STAMP board
+ */
+
+#ifndef __CONFIG_STAMP_H__
+#define __CONFIG_STAMP_H__
+
+#define CONFIG_STAMP			1
+#define CONFIG_RTC_BFIN			1
+#define CONFIG_BF533			1
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF533_BYPASS_BOOT	0x0001	/* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT		0x0002	/* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT		0x0004	/* Bootmode 3: Boot from SPI flash */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE		BF533_BYPASS_BOOT
+/* #define BFIN_BOOT_MODE	BF533_SPI_BOOT */
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF531		0x31
+#define ADSP_BF532		0x32
+#define ADSP_BF533		0x33
+#define BFIN_CPU		ADSP_BF533
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/*
+ * Stringize definitions - needed for environmental settings
+ */
+#define STRINGIZE2(x) #x
+#define STRINGIZE(x) STRINGIZE2(x)
+
+/*
+ * Board settings
+ */
+#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_SMC91111_BASE	0x20300300
+
+/* FLASH/ETHERNET uses the same address range */
+#define SHARED_RESOURCES 	1
+
+/* Is I2C bit-banged? */
+#define CONFIG_SOFT_I2C		1
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL			PF3
+#define PF_SDA			PF2
+
+/*
+ * Video splash screen support
+ */
+#define  CONFIG_VIDEO		0
+
+#define CONFIG_VDSP		1
+
+/*
+ * Clock settings
+ */
+
+/* CONFIG_CLKIN_HZ is any value in Hz				*/
+#define CONFIG_CLKIN_HZ		11059200
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
+/*						    1=CLKIN/2	*/
+#define CONFIG_CLKIN_HALF	0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
+/*						 1=bypass PLL	*/
+#define CONFIG_PLL_BYPASS	0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
+/* Values can range from 1-64					*/
+#define CONFIG_VCO_MULT		36
+/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
+/* Values can be 1, 2, 4, or 8 ONLY				*/
+#define CONFIG_CCLK_DIV		1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
+/* Values can range from 1-15					*/
+#define CONFIG_SCLK_DIV		5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
+/* Values can range from 2-65535				*/
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
+#define CONFIG_SPI_BAUD		2
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_SPI_BAUD_INITBLOCK	4
+#endif
+
+/*
+ * Network settings
+ */
+
+#if (CONFIG_DRIVER_SMC91111)
+#if 0
+#define	CONFIG_MII
+#endif
+
+/* network support */
+#define CONFIG_IPADDR		192.168.0.15
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_GATEWAYIP	192.168.0.1
+#define CONFIG_SERVERIP		192.168.0.2
+#define CONFIG_HOSTNAME		STAMP
+#define CONFIG_ROOTPATH		/checkout/uClinux-dist/romfs
+
+/* To remove hardcoding and enable MAC storage in EEPROM  */
+/* #define CONFIG_ETHADDR		02:80:ad:20:31:b8 */
+#endif /* CONFIG_DRIVER_SMC91111 */
+
+/*
+ * Flash settings
+ */
+
+#define CFG_FLASH_CFI		/* The flash is CFI compatible  */
+#define CFG_FLASH_CFI_DRIVER	/* Use common CFI driver	*/
+#define	CFG_FLASH_CFI_AMD_RESET
+
+#define CFG_FLASH_BASE		0x20000000
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	67	/* max number of sectors on one chip */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		0x20004000
+#define	CFG_ENV_OFFSET		(CFG_ENV_ADDR - CFG_FLASH_BASE)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_HEADER		(CFG_ENV_OFFSET + 0x12A)	/* 0x12A is the length of LDR file header */
+#endif
+
+#define	CFG_ENV_SIZE		0x2000
+#define CFG_ENV_SECT_SIZE 	0x2000	/* Total Size of Environment Sector */
+#define	ENV_IS_EMBEDDED
+
+#define CFG_FLASH_ERASE_TOUT	30000	/* Timeout for Chip Erase (in ms) */
+#define CFG_FLASH_ERASEBLOCK_TOUT	5000	/* Timeout for Block Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT	1	/* Timeout for Flash Write (in ms) */
+
+/* JFFS Partition offset set  */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS  1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 	11
+
+/*
+ * following timeouts shall be used once the
+ * Flash real protection is enabled
+ */
+#define CFG_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE		128	/* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH     11	/* 8, 9, 10, 11    */
+#define CONFIG_MEM_MT48LC64M4A2FB_7E	1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_MEMTEST_START	0x00000000	/* memtest works on */
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on */
+#endif
+
+#define	CFG_SDRAM_BASE		0x00000000
+
+#define CFG_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 *1024)
+#define CFG_MEMTEST_END		(CFG_MAX_RAM_SIZE - 0x80000 - 1)
+#define CONFIG_LOADADDR		0x01000000
+
+#define CFG_LOAD_ADDR 		CONFIG_LOADADDR
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 << 10)     /* Reserve 128 kB for malloc()	*/
+#define CFG_GBL_DATA_SIZE	0x4000		/* Reserve 16k for Global Data  */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+
+#define CFG_MONITOR_BASE		(CFG_MAX_RAM_SIZE - 0x40000)
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)
+
+/* Check to make sure everything fits in SDRAM */
+#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
+	#error Memory Map does not fit into configuration
+#endif
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
+#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
+#else
+#undef CONFIG_SPI_FLASH_FAST_READ
+#endif
+#endif
+
+/*
+ * Command settings
+ */
+
+#define CFG_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING	1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_AUTOLOAD		"no"	/*rarpb, bootp or dhcp commands will perform only a */
+#endif
+
+/* configuration lookup from the BOOTP/DHCP server, */
+/* but not try to load any image using TFTP	    */
+
+#define CONFIG_BOOTDELAY	5
+#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_BOOTCOMMAND	"run ramboot"
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_BOOTCOMMAND 	"eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
+#endif
+
+#define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw console=ttyBF0,57600"
+
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_COMMANDS1	(CONFIG_CMD_DFL | \
+				 CFG_CMD_PING   | \
+				 CFG_CMD_ELF    | \
+				 CFG_CMD_CACHE  | \
+				 CFG_CMD_JFFS2  | \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_DATE)
+
+#else
+#define CONFIG_COMMANDS1	(CONFIG_CMD_DFL | \
+				 CFG_CMD_ELF    | \
+				 CFG_CMD_CACHE  | \
+				 CFG_CMD_JFFS2  | \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_DATE)
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+		"$(rootpath) console=ttyBF0,57600\0" \
+	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+		"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+	"ramboot=tftpboot $(loadaddr) linux; " \
+		"run ramargs;run addip;bootelf\0" \
+	"nfsboot=tftpboot $(loadaddr) linux; " \
+		"run nfsargs;run addip;bootelf\0" \
+	"flashboot=bootm 0x20100000\0" \
+	"update=tftpboot $(loadaddr) u-boot.bin; " \
+		"protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
+		"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+	""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+	"flashboot=bootm 0x20100000\0" \
+	"
+#endif
+
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+		"$(rootpath) console=ttyBF0,57600\0"	\
+	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+		"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+	"ramboot=tftpboot $(loadaddr) linux; " \
+		"run ramargs;run addip;bootelf\0" \
+	"nfsboot=tftpboot $(loadaddr) linux; "	\
+		"run nfsargs;run addip;bootelf\0" \
+	"flashboot=bootm 0x20100000\0" \
+	"update=tftpboot $(loadaddr) u-boot.ldr;"	\
+		"eeprom write $(loadaddr) 0x0 $(filesize);\0"\
+	""
+#endif
+
+#ifdef CONFIG_SOFT_I2C
+#if (!CONFIG_SOFT_I2C)
+#undef CONFIG_SOFT_I2C
+#endif
+#endif
+
+#if (CONFIG_SOFT_I2C)
+#define CONFIG_COMMANDS2   CFG_CMD_I2C
+#else
+#define CONFIG_COMMANDS2 0
+#endif /* CONFIG_SOFT_I2C */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_COMMANDS  ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 | CFG_CMD_DHCP)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_COMMANDS  ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2)
+#endif
+
+/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Console settings
+ */
+
+#define CONFIG_BAUDRATE		57600
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (BFIN_CPU == ADSP_BF531)
+#define	CFG_PROMPT	"serial_bf531> "	/* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define	CFG_PROMPT	"serial_bf532> "	/* Monitor Command Prompt */
+#else
+#define	CFG_PROMPT	"serial_bf533> "	/* Monitor Command Prompt */
+#endif
+#else
+#if (BFIN_CPU == ADSP_BF531)
+#define	CFG_PROMPT	"bf531> "	/* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define	CFG_PROMPT	"bf532> "	/* Monitor Command Prompt */
+#else
+#define	CFG_PROMPT	"bf533> "	/* Monitor Command Prompt */
+#endif
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE	(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CONFIG_LOADS_ECHO	1
+
+/*
+ * I2C settings
+ * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
+ */
+#if (CONFIG_SOFT_I2C)
+
+#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
+#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit)	if(bit) { \
+				*pFIO_FLAG_S = PF_SDA; \
+				asm("ssync;"); \
+				} \
+			else	{ \
+				*pFIO_FLAG_C = PF_SDA; \
+				asm("ssync;"); \
+				}
+#define I2C_SCL(bit)	if(bit) { \
+				*pFIO_FLAG_S = PF_SCL; \
+				asm("ssync;"); \
+				} \
+			else	{ \
+				*pFIO_FLAG_C = PF_SCL; \
+				asm("ssync;"); \
+				}
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED		50000
+#define CFG_I2C_SLAVE		0xFE
+#endif /* CONFIG_SOFT_I2C */
+
+/*
+ * Compact Flash settings
+ */
+
+/* Enabled below option for CF support */
+/* #define CONFIG_STAMP_CF	1 */
+
+#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
+
+#define CONFIG_MISC_INIT_R	1
+#define CONFIG_DOS_PARTITION	1
+/*
+ * IDE/ATA stuff
+ */
+#undef  CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
+#undef  CONFIG_IDE_LED			/* no led for ide supported */
+#undef  CONFIG_IDE_RESET		/* no reset for ide supported */
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR	0x20200000
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0x0007	/* Offset for alternate registers */
+
+#define CFG_ATA_STRIDE		2
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define	CFG_HZ			1000	/* 1ms time tick */
+
+#define CFG_BOOTM_LEN		0x4000000/* Large Image Length, set to 64 Meg */
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1	/* Show boot progress on LEDs */
+
+#define CONFIG_SPI
+
+#ifdef  CONFIG_VIDEO
+#if (CONFIG_VIDEO)
+#define CONFIG_SPLASH_SCREEN	1
+#define CONFIG_SILENT_CONSOLE	1
+#else
+#undef CONFIG_VIDEO
+#endif
+#endif
+
+/*
+ * FLASH organization and environment definitions
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)/* Initial Memory map for Linux */
+
+/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
+/*#define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL		(B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
+				B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
+#define AMBCTL1VAL   		(B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
+				B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
+*/
+#define AMGCTLVAL		0xFF
+#define AMBCTL0VAL		0xBBC3BBC3
+#define AMBCTL1VAL		0x99B39983
+#define CF_AMBCTL1VAL		0x99B3ffc2
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP		0x8
+#define SHT_STRTAB_VDSP		0x1
+#define ELFSHDRSIZE_VDSP	0x2C
+#define VDSP_ENTRY_ADDR		0xFFA00000
+#endif
+
+#endif
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
new file mode 100644
index 0000000000..f6755acf69
--- /dev/null
+++ b/include/configs/bf537-stamp.h
@@ -0,0 +1,502 @@
+/*
+ * U-boot - Configuration file for BF537 STAMP board
+ */
+
+#ifndef __CONFIG_BF537_H__
+#define __CONFIG_BF537_H__
+
+#define CFG_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING	1
+#define CONFIG_BAUDRATE		57600
+/* Set default serial console for bf537 */
+#define CONFIG_UART_CONSOLE	0
+#define CONFIG_BF537		1
+#define CONFIG_BOOTDELAY	5
+/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
+/*#define CONFIG_BF537_STAMP_LEDCMD	1*/
+
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF537_BYPASS_BOOT	0x0011	/* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM)  */
+#define BF537_PARA_BOOT		0x0012	/* Bootmode 1: Boot from 8-bit or 16-bit flash                          */
+#define BF537_SPI_MASTER_BOOT	0x0014	/* Bootmode 3: SPI master mode boot from SPI flash                      */
+#define BF537_SPI_SLAVE_BOOT	0x0015	/* Bootmode 4: SPI slave mode boot from SPI flash                       */
+#define BF537_TWI_MASTER_BOOT	0x0016	/* Bootmode 5: TWI master mode boot from EEPROM                         */
+#define BF537_TWI_SLAVE_BOOT	0x0017	/* Bootmode 6: TWI slave mode boot from EEPROM                          */
+#define BF537_UART_BOOT		0x0018	/* Bootmode 7: UART slave mdoe boot via UART host                       */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE		BF537_BYPASS_BOOT
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF534		0x34
+#define ADSP_BF536		0x36
+#define ADSP_BF537		0x37
+#define BFIN_CPU		ADSP_BF537
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST_TEST
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+#define CONFIG_RTC_BFIN		1
+#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
+
+/* CONFIG_CLKIN_HZ is any value in Hz				*/
+#define CONFIG_CLKIN_HZ		25000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
+/*						    1=CLKIN/2	*/
+#define CONFIG_CLKIN_HALF	0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/*						    1=bypass PLL*/
+#define CONFIG_PLL_BYPASS	0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
+/* Values can range from 1-64					*/
+#define CONFIG_VCO_MULT			20
+/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
+/* Values can be 1, 2, 4, or 8 ONLY				*/
+#define CONFIG_CCLK_DIV			1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
+/* Values can range from 1-15					*/
+#define CONFIG_SCLK_DIV			5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
+/* Values can range from 2-65535				*/
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
+#define CONFIG_SPI_BAUD			2
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CONFIG_SPI_BAUD_INITBLOCK	4
+#endif
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
+#define CONFIG_SPI_FLASH_FAST_READ 1	/* Needed if SPI_CLK > 20 MHz */
+#else
+#undef CONFIG_SPI_FLASH_FAST_READ
+#endif
+#endif
+
+#define CONFIG_MEM_SIZE			64	/* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH		10	/* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC32M8A2_75	1
+
+#define CONFIG_LOADS_ECHO		1
+
+/*
+ * rarpb, bootp or dhcp commands will perform only a
+ * configuration lookup from the BOOTP/DHCP server
+ * but not try to load any image using TFTP
+ */
+#define CFG_AUTOLOAD			"no"
+
+/*
+ * Network Settings
+ */
+/* network support */
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_IPADDR		192.168.0.15
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_GATEWAYIP	192.168.0.1
+#define CONFIG_SERVERIP		192.168.0.2
+#define CONFIG_HOSTNAME		BF537
+#endif
+
+#define CONFIG_ROOTPATH		/romfs
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR	02:80:ad:20:31:e8 */
+/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
+
+#define CFG_LONGHELP		1
+#define CONFIG_BOOTDELAY	5
+#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
+#define CONFIG_BOOTCOMMAND 	"run ramboot"
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) && defined(CONFIG_POST_TEST)
+/* POST support */
+#define CONFIG_POST 		( CFG_POST_MEMORY | \
+				  CFG_POST_UART	  | \
+				  CFG_POST_FLASH  | \
+				  CFG_POST_ETHER  | \
+				  CFG_POST_LED	  | \
+				  CFG_POST_BUTTON)
+#else
+#undef CONFIG_POST
+#endif
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG	CFG_CMD_DIAG
+#define FLASH_START_POST_BLOCK	11	/* Should > = 11 */
+#define FLASH_END_POST_BLOCK	71	/* Should < = 71 */
+#else
+#define CFG_CMD_POST_DIAG	0
+#endif
+
+/* CF-CARD IDE-HDD Support */
+
+/* #define CONFIG_BFIN_TRUE_IDE */	/* Add CF flash card support */
+/* #define CONFIG_BFIN_CF_IDE */	/* Add CF flash card support */
+/* #define CONFIG_BFIN_HDD_IDE */	/* Add IDE Disk Drive (HDD) support */
+
+#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
+# define CONFIG_BFIN_IDE	1
+# define ADD_IDE_CMD		CFG_CMD_IDE
+#else
+# define ADD_IDE_CMD		0
+#endif
+
+/*#define CONFIG_BF537_NAND */		/* Add nand flash support */
+
+#ifdef CONFIG_BF537_NAND
+# define ADD_NAND_CMD		CFG_CMD_NAND
+#else
+# define ADD_NAND_CMD		0
+#endif
+
+#define CONFIG_NETCONSOLE	1
+#define CONFIG_NET_MULTI	1
+
+#if (BFIN_CPU == ADSP_BF534)
+#define CONFIG_BFIN_CMD		(CONFIG_CMD_DFL & ~CFG_CMD_NET)
+#else
+#define CONFIG_BFIN_CMD		(CONFIG_CMD_DFL | CFG_CMD_PING)
+#endif
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
+#define CONFIG_COMMANDS		(CONFIG_BFIN_CMD| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_I2C	| \
+				 CFG_CMD_CACHE  | \
+				 CFG_CMD_JFFS2	| \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_DHCP   | \
+				 ADD_IDE_CMD	| \
+				 ADD_NAND_CMD	| \
+				 CFG_CMD_POST_DIAG | \
+				 CFG_CMD_DATE)
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CONFIG_COMMANDS		(CONFIG_BFIN_CMD| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_I2C	| \
+				 CFG_CMD_CACHE  | \
+				 CFG_CMD_JFFS2	| \
+				 CFG_CMD_EEPROM | \
+				 ADD_IDE_CMD	| \
+				 CFG_CMD_DATE)
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+#define CONFIG_LOADADDR	0x1000000
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "		\
+	"nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
+	"addip=setenv bootargs $(bootargs) "			\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+	":$(hostname):eth0:off\0"				\
+	"ramboot=tftpboot $(loadaddr) linux;"			\
+	"run ramargs;run addip;bootelf\0"			\
+	"nfsboot=tftpboot $(loadaddr) linux;"			\
+	"run nfsargs;run addip;bootelf\0"			\
+	"flashboot=bootm 0x20100000\0"				\
+	"update=tftpboot $(loadaddr) u-boot.bin;"		\
+	"protect off 0x20000000 0x2007FFFF;"			\
+	"erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0"	\
+	""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	\
+	"flashboot=bootm 0x20100000\0"				\
+	""
+#endif
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (BFIN_CPU != ADSP_BF534)
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "		\
+	"nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
+	"addip=setenv bootargs $(bootargs) "			\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+	":$(hostname):eth0:off\0"				\
+	"ramboot=tftpboot $(loadaddr) linux;"			\
+	"run ramargs;run addip;bootelf\0"			\
+	"nfsboot=tftpboot $(loadaddr) linux;"			\
+	"run nfsargs;run addip;bootelf\0"			\
+	"flashboot=bootm 0x20100000\0"				\
+	"update=tftpboot $(loadaddr) u-boot.ldr;"		\
+	"eeprom write $(loadaddr) 0x0 $(filesize);\0"		\
+	""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	\
+	"flashboot=bootm 0x20100000\0"				\
+	""
+#endif
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (BFIN_CPU == ADSP_BF534)
+#define	CFG_PROMPT		"serial_bf534> "	/* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF536)
+#define	CFG_PROMPT		"serial_bf536> "	/* Monitor Command Prompt */
+#else
+#define	CFG_PROMPT		"serial_bf537> "	/* Monitor Command Prompt */
+#endif
+#else
+#if (BFIN_CPU == ADSP_BF534)
+#define	CFG_PROMPT		"bf534> "	/* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF536)
+#define	CFG_PROMPT		"bf536> "	/* Monitor Command Prompt */
+#else
+#define	CFG_PROMPT		"bf537> "	/* Monitor Command Prompt */
+#endif
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+#define CFG_MAX_RAM_SIZE       	(CONFIG_MEM_SIZE * 1024*1024)
+#define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_MEMTEST_START	0x0	/* memtest works on */
+#define CFG_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024*1024)	/* 1 ... 63 MB in DRAM */
+#define	CFG_LOAD_ADDR		CONFIG_LOADADDR	/* default load address */
+#define	CFG_HZ			1000	/* decrementer freq: 10 ms ticks */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+#define	CFG_SDRAM_BASE		0x00000000
+
+#define CFG_FLASH_BASE		0x20000000
+
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_SIZE	0x4000
+#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)
+
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
+
+#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) || (BFIN_BOOT_MODE == BF537_UART_BOOT)
+/* for bf537-stamp, usrt boot mode still store env in flash */
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		0x20004000
+#define CFG_ENV_OFFSET		(CFG_ENV_ADDR - CFG_FLASH_BASE)
+#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_HEADER		(CFG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
+#endif
+#define CFG_ENV_SIZE		0x2000
+#define	CFG_ENV_SECT_SIZE	0x2000	/* Total Size of Environment Sector */
+/* #if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) */
+#define ENV_IS_EMBEDDED
+/* #endif */
+
+/* JFFS Partition offset set  */
+#define CFG_JFFS2_FIRST_BANK	0
+#define CFG_JFFS2_NUM_BANKS	1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR	15
+
+#define CONFIG_SPI
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+
+#define POLL_MODE		1
+#define FLASH_TOT_SECT		71
+#define FLASH_SIZE		0x400000
+#define CFG_FLASH_SIZE		0x400000
+
+/*
+ * Board NAND Infomation
+ */
+
+#define CFG_NAND_ADDR		0x20212000
+#define CFG_NAND_BASE		CFG_NAND_ADDR
+#define CFG_MAX_NAND_DEVICE	1
+#define SECTORSIZE		512
+#define ADDR_COLUMN		1
+#define ADDR_PAGE		2
+#define ADDR_COLUMN_PAGE	3
+#define NAND_ChipID_UNKNOWN	0x00
+#define NAND_MAX_FLOORS		1
+#define NAND_MAX_CHIPS		1
+#define BFIN_NAND_READY		PF3
+
+#define NAND_WAIT_READY(nand)  			\
+	do { 					\
+		int timeout = 0; 		\
+		while(!(*pPORTFIO & PF3)) 	\
+			if (timeout++ > 100000)	\
+				break;		\
+	} while (0)
+
+#define BFIN_NAND_CLE		(1<<2)	/* A2 -> Command Enable */
+#define BFIN_NAND_ALE		(1<<1)	/* A1 -> Address Enable */
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+/*
+ * Initialize PSD4256 registers for using I2C
+ */
+#define CONFIG_MISC_INIT_R
+
+#define CFG_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */
+
+/*
+ * I2C settings
+ * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ */
+/* #define CONFIG_SOFT_I2C	1*/	/* I2C bit-banged */
+#define CONFIG_HARD_I2C		1	/* I2C TWI */
+#if defined CONFIG_HARD_I2C
+#define CONFIG_TWICLK_KHZ	50
+#endif
+
+#if defined CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL			PF0
+#define PF_SDA			PF1
+
+#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
+#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit)		if(bit) { \
+					*pFIO_FLAG_S = PF_SDA; \
+					asm("ssync;"); \
+					} \
+				else    { \
+					*pFIO_FLAG_C = PF_SDA; \
+					asm("ssync;"); \
+					}
+#define I2C_SCL(bit)		if(bit) { \
+					*pFIO_FLAG_S = PF_SCL; \
+					asm("ssync;"); \
+					} \
+				else    { \
+					*pFIO_FLAG_C = PF_SCL; \
+					asm("ssync;"); \
+					}
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+#endif
+
+#define CFG_I2C_SPEED		50000
+#define CFG_I2C_SLAVE		0xFE
+
+/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
+/* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
+				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
+#define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
+				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
+*/
+
+#define AMGCTLVAL		0xFF
+#define AMBCTL0VAL		0x7BB07BB0
+#define AMBCTL1VAL		0xFFC27BB0
+
+#define CONFIG_VDSP		1
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP		0x8
+#define SHT_STRTAB_VDSP		0x1
+#define ELFSHDRSIZE_VDSP	0x2C
+#define VDSP_ENTRY_ADDR		0xFFA00000
+#endif
+
+#if defined(CONFIG_BFIN_IDE)
+
+#define CONFIG_DOS_PARTITION	1
+/*
+ * IDE/ATA stuff
+ */
+#undef  CONFIG_IDE_8xx_DIRECT	/* no pcmcia interface required */
+#undef  CONFIG_IDE_LED		/* no led for ide supported */
+#undef  CONFIG_IDE_RESET	/* no reset for ide supported */
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1)	/* max. 1 drives per IDE bus */
+
+#undef  AMBCTL1VAL
+#define AMBCTL1VAL		0xFFC3FFC3
+
+#define CONFIG_CF_ATASEL_DIS	0x20311800
+#define CONFIG_CF_ATASEL_ENA	0x20311802
+
+#if defined(CONFIG_BFIN_TRUE_IDE)
+/*
+ * Note that these settings aren't for the most part used in include/ata.h
+ * when all of the ATA registers are setup
+ */
+#define CFG_ATA_BASE_ADDR	0x2031C000
+#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0x001C	/* Offset for alternate registers */
+#define CFG_ATA_STRIDE		2	/* CF.A0 --> Blackfin.Ax */
+#endif				/* CONFIG_BFIN_TRUE_IDE */
+
+#if defined(CONFIG_BFIN_CF_IDE)	/* USE CompactFlash Storage Card in the common memory space */
+#define CFG_ATA_BASE_ADDR	0x20211800
+#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0x000E	/* Offset for alternate registers */
+#define CFG_ATA_STRIDE		1	/* CF.A0 --> Blackfin.Ax */
+#endif				/* CONFIG_BFIN_CF_IDE */
+
+#if defined(CONFIG_BFIN_HDD_IDE)	/* USE TRUE IDE */
+#define CFG_ATA_BASE_ADDR	0x20314000
+#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0x001C	/* Offset for alternate registers */
+#define CFG_ATA_STRIDE		2	/* CF.A0 --> Blackfin.A1 */
+
+#undef  CONFIG_SCLK_DIV
+#define CONFIG_SCLK_DIV		8
+#endif				/* CONFIG_BFIN_HDD_IDE */
+
+#endif				/*CONFIG_BFIN_IDE */
+
+#endif
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
new file mode 100644
index 0000000000..8d826faaa0
--- /dev/null
+++ b/include/configs/bf561-ezkit.h
@@ -0,0 +1,244 @@
+/*
+ * U-boot - Configuration file for BF561 EZKIT board
+ */
+
+#ifndef __CONFIG_EZKIT561_H__
+#define __CONFIG_EZKIT561_H__
+
+#define CONFIG_VDSP		1
+#define CONFIG_BF561		1
+
+#define CFG_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING	1
+#define CONFIG_BAUDRATE		57600
+/* Set default serial console for bf537 */
+#define CONFIG_UART_CONSOLE	0
+#define CONFIG_EZKIT561		1
+#define CONFIG_BOOTDELAY	5
+
+#define CONFIG_PANIC_HANG 1
+
+/*
+* Boot Mode Set
+* Blackfin can support several boot modes
+*/
+#define BF561_BYPASS_BOOT	0x21
+#define BF561_PARA_BOOT		0x22
+#define BF561_SPI_BOOT		0x24
+/* Define the boot mode */
+#define BFIN_BOOT_MODE	BF561_BYPASS_BOOT
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/*
+ * Stringize definitions - needed for environmental settings
+ */
+#define STRINGIZE2(x) #x
+#define STRINGIZE(x) STRINGIZE2(x)
+
+/*
+ * Board settings
+ */
+#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_SMC91111_BASE	0x2C010300
+#define CONFIG_ASYNC_EBIU_BASE	CONFIG_SMC91111_BASE & ~(4*1024*1024)
+#define CONFIG_SMC_USE_32_BIT	1
+#define CONFIG_MISC_INIT_R	1
+
+/*
+ * Clock settings
+ */
+
+/* CONFIG_CLKIN_HZ is any value in Hz				*/
+#define CONFIG_CLKIN_HZ		30000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
+/*						    1=CLKIN/2	*/
+#define CONFIG_CLKIN_HALF	0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
+/*						 1=bypass PLL	*/
+#define CONFIG_PLL_BYPASS	0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is	*/
+/* Values can range from 1-64					*/
+#define CONFIG_VCO_MULT		20
+/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
+/* Values can be 1, 2, 4, or 8 ONLY				*/
+#define CONFIG_CCLK_DIV		1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
+/* Values can range from 1-15					*/
+#define CONFIG_SCLK_DIV		5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
+/* Values can range from 2-65535				*/
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
+#define CONFIG_SPI_BAUD		2
+#define CONFIG_SPI_BAUD_INITBLOCK	4
+
+/*
+ * Network settings
+ */
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_IPADDR		192.168.0.15
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_GATEWAYIP	192.168.0.1
+#define CONFIG_SERVERIP		192.168.0.2
+#define CONFIG_HOSTNAME		ezkit561
+#define CONFIG_ROOTPATH		/arm-cross-build/BF561/uClinux-dist/romfs
+#endif				/* CONFIG_DRIVER_SMC91111 */
+
+/*
+ * Flash settings
+ */
+
+#define CFG_FLASH_CFI		/* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER	/* Use common CFI driver */
+#define CFG_FLASH_CFI_AMD_RESET
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_FLASH_BASE		0x20000000
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	135	/* max number of sectors on one chip */
+#define CFG_ENV_ADDR		0x20020000
+#define	CFG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */
+/* JFFS Partition offset set  */
+#define CFG_JFFS2_FIRST_BANK	0
+#define CFG_JFFS2_NUM_BANKS	1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR	8
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE			64	/* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH		9	/* 8, 9, 10, 11    */
+#define CONFIG_MEM_MT48LC16M16A2TG_75	1
+
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 * 1024)
+
+#define CFG_MEMTEST_START	0x0	/* memtest works on */
+#define CFG_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024*1024)	/* 1 ... 63 MB in DRAM */
+
+#define	CONFIG_LOADADDR		0x01000000	/* default load address */
+#define CFG_LOAD_ADDR		CONFIG_LOADADDR
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
+#define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
+
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+#define CFG_GBL_DATA_SIZE	0x4000
+#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
+#endif
+
+/*
+ * Command settings
+ */
+
+#define CFG_AUTOLOAD	"no"	/* rarpb, bootp, dhcp commands will	*/
+				/* only perform a configuration		*/
+				/* lookup from the BOOTP/DHCP server	*/
+				/* but not try to load any image	*/
+				/* using TFTP				*/
+#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, */
+					/* currently its disabled */
+#define CONFIG_BOOTCOMMAND	"run ramboot"
+#define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw console=ttyBF0,57600"
+
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_COMMANDS1	(CONFIG_CMD_DFL	| \
+				 CFG_CMD_PING	| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_CACHE	| \
+				 CFG_CMD_JFFS2	| \
+				 CFG_CMD_DHCP)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" 		\
+	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):"	\
+		"$(rootpath) console=ttyBF0,57600\0"						\
+	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):"	\
+		"$(gatewayip):$(netmask):$(hostname):eth0:off\0"	\
+	"ramboot=tftpboot $(loadaddr) linux; "		\
+		"run ramargs; run addip; bootelf\0"			\
+	"nfsboot=tftpboot $(loadaddr) linux; "		\
+		"run nfsargs; run addip; bootelf\0"			\
+	"update=tftpboot $(loadaddr) u-boot.bin; "	\
+		"protect off 0x20000000 0x2003FFFF; "			\
+		"erase 0x20000000 0x2003FFFF; "				\
+		"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+	""
+#else
+#define CONFIG_COMMANDS1	(CONFIG_CMD_DFL	| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_CACHE	| \
+				 CFG_CMD_JFFS2)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"		\
+	"flashboot=bootm 0x20100000\0"					\
+	""
+#endif
+
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Console settings
+ */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define	CFG_PROMPT		"ezkit> "	/* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size */
+#else
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size */
+#endif
+#define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16		/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CONFIG_LOADS_ECHO	1
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_HZ			1000		/* decrementer freq: 10 ms ticks */
+#define CFG_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */
+
+/*
+ * FLASH organization and environment definitions
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+#define AMGCTLVAL		0x3F
+#define AMBCTL0VAL		0x7BB07BB0
+#define AMBCTL1VAL		0xFFC27BB0
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP		0x8
+#define SHT_STRTAB_VDSP		0x1
+#define ELFSHDRSIZE_VDSP	0x2C
+#define VDSP_ENTRY_ADDR		0xFFA00000
+#endif
+
+#endif				/* __CONFIG_EZKIT561_H__ */
diff --git a/include/configs/ezkit533.h b/include/configs/ezkit533.h
deleted file mode 100644
index 5eda6732ca..0000000000
--- a/include/configs/ezkit533.h
+++ /dev/null
@@ -1,188 +0,0 @@
-#ifndef __CONFIG_EZKIT533_H__
-#define __CONFIG_EZKIT533_H__
-
-#define CFG_LONGHELP		1
-#define CONFIG_BAUDRATE		57600
-#define CONFIG_STAMP		1
-#define CONFIG_BOOTDELAY	5
-
-#define CONFIG_DRIVER_SMC91111	1
-#define CONFIG_SMC91111_BASE	0x20310300
-#if 0
-#define CONFIG_MII
-#define CFG_DISCOVER_PHY
-#endif
-
-#define CONFIG_RTC_BF533	1
-#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
-
-/* CONFIG_CLKIN_HZ is any value in Hz				 */
-#define CONFIG_CLKIN_HZ		 27000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	 */
-/*						    1=CLKIN/2	 */
-#define CONFIG_CLKIN_HALF		0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	 */
-/*						 1=bypass PLL	 */
-#define CONFIG_PLL_BYPASS		0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	 */
-/* Values can range from 1-64					 */
-#define CONFIG_VCO_MULT			22
-/* CONFIG_CCLK_DIV controls what the core clock divider is	 */
-/* Values can be 1, 2, 4, or 8 ONLY				 */
-#define CONFIG_CCLK_DIV			1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15					 */
-#define CONFIG_SCLK_DIV			5
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE			32	       /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH		 9	       /* 8, 9, 10, 11	  */
-#define CONFIG_MEM_MT48LC16M16A2TG_75	 1
-
-#define CONFIG_LOADS_ECHO	1
-
-
-#define CONFIG_COMMANDS			(CONFIG_CMD_DFL | \
-					 CFG_CMD_PING	| \
-					 CFG_CMD_ELF	| \
-					 CFG_CMD_I2C	| \
-					 CFG_CMD_JFFS2	| \
-					 CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off"
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-#define CFG_PROMPT		"ezkit> "	/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE		256	/* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
-#define CFG_MAXARGS		16	/* max number of command args */
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START	0x00100000	/* memtest works on */
-#define CFG_MEMTEST_END		0x01F00000	/* 1 ... 31 MB in DRAM */
-#define CFG_LOAD_ADDR		0x01000000	/* default load address */
-#define CFG_HZ			1000	/* decrementer freq: 10 ms ticks */
-#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_MAX_RAM_SIZE	0x02000000
-#define CFG_FLASH_BASE		0x20000000
-
-#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE	0x4000
-#define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)
-
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-#define CFG_FLASH0_BASE		0x20000000
-#define CFG_FLASH1_BASE		0x20200000
-#define CFG_FLASH2_BASE		0x20280000
-#define CFG_MAX_FLASH_BANKS	3	/* max number of memory banks */
-#define CFG_MAX_FLASH_SECT	40	/* max number of sectors on one chip */
-
-#define CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_ADDR		0x20020000
-#define CFG_ENV_SECT_SIZE	0x10000 /* Total Size of Environment Sector */
-
-/* JFFS Partition offset set  */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS  1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR		       11
-
-
-/*
- * Stack sizes
- */
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-
-#define POLL_MODE		1
-#define FLASH_TOT_SECT		40
-#define FLASH_SIZE		0x220000
-#define CFG_FLASH_SIZE		0x220000
-
-/*
- * Initialize PSD4256 registers for using I2C
- */
-#define CONFIG_MISC_INIT_R
-
-/*
- * I2C settings
- * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
- */
-#define CONFIG_SOFT_I2C			1	/* I2C bit-banged		*/
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PF_SCL				PF0
-#define PF_SDA				PF1
-
-#define I2C_INIT			(*pFIO_DIR |=  PF_SCL); asm("ssync;")
-#define I2C_ACTIVE			(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE			(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ			((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit)			if(bit) { \
-							*pFIO_FLAG_S = PF_SDA; \
-							asm("ssync;"); \
-						} \
-					else	{ \
-							*pFIO_FLAG_C = PF_SDA; \
-							asm("ssync;"); \
-						}
-#define I2C_SCL(bit)			if(bit) { \
-							*pFIO_FLAG_S = PF_SCL; \
-							asm("ssync;"); \
-						} \
-					else	{ \
-							*pFIO_FLAG_C = PF_SCL; \
-							asm("ssync;"); \
-						}
-#define I2C_DELAY			udelay(5)	/* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED			50000
-#define CFG_I2C_SLAVE			0xFE
-
-
-#define __ADSPLPBLACKFIN__	1
-#define __ADSPBF533__		1
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL |	\
-				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN |	\
-				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
-#define AMGCTLVAL		0xFF
-#define AMBCTL0VAL		0x7BB07BB0
-#define AMBCTL1VAL		0xFFC27BB0
-
-#define CONFIG_VDSP		1
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP		0x8
-#define SHT_STRTAB_VDSP		0x1
-#define ELFSHDRSIZE_VDSP	0x2C
-#define VDSP_ENTRY_ADDR		0xFFA00000
-#endif
-
-#endif
diff --git a/include/configs/stamp.h b/include/configs/stamp.h
deleted file mode 100644
index 248ca70de0..0000000000
--- a/include/configs/stamp.h
+++ /dev/null
@@ -1,333 +0,0 @@
-/*
- * U-boot - stamp.h  Configuration file for STAMP board
- *			having BF533 processor
- *
- * Copyright (c) 2005 blackfin.uclinux.org
- *
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_STAMP_H__
-#define __CONFIG_STAMP_H__
-
-/*
- * Board settings
- *
- */
-
-#define __ADSPLPBLACKFIN__		1
-#define __ADSPBF533__			1
-#define CONFIG_STAMP			1
-#define CONFIG_RTC_BF533		1
-
-/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES		1
-
-#define CONFIG_VDSP			1
-
-/*
- * Clock settings
- *
- */
-
-/* CONFIG_CLKIN_HZ is any value in Hz				 */
-#define CONFIG_CLKIN_HZ			11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	 */
-/*						    1=CLKIN/2	 */
-#define CONFIG_CLKIN_HALF		0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	 */
-/*						 1=bypass PLL	 */
-#define CONFIG_PLL_BYPASS		0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	 */
-/* Values can range from 1-64					 */
-#define CONFIG_VCO_MULT			45
-/* CONFIG_CCLK_DIV controls what the core clock divider is	 */
-/* Values can be 1, 2, 4, or 8 ONLY				 */
-#define CONFIG_CCLK_DIV			1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15					 */
-#define CONFIG_SCLK_DIV			6
-
-/*
- * Network Settings
- */
-/* network support */
-#define CONFIG_IPADDR		192.168.0.15
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_GATEWAYIP	192.168.0.1
-#define CONFIG_SERVERIP		192.168.0.2
-#define CONFIG_HOSTNAME		STAMP
-#define CONFIG_ROOTPATH			/checkout/uClinux-dist/romfs
-
-/* To remove hardcoding and enable MAC storage in EEPROM  */
-/* #define CONFIG_ETHADDR		02:80:ad:20:31:b8 */
-
-/*
- * Command settings
- *
- */
-
-#define CFG_LONGHELP			1
-
-#define CONFIG_BOOTDELAY		5
-#define CONFIG_BOOT_RETRY_TIME		-1	/* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND		"run ramboot"
-#define CONFIG_AUTOBOOT_PROMPT		"autoboot in %d seconds\n"
-
-#define CONFIG_COMMANDS			(CONFIG_CMD_DFL | \
-					 CFG_CMD_PING	| \
-					 CFG_CMD_ELF	| \
-					 CFG_CMD_I2C	| \
-					 CFG_CMD_CACHE	| \
-					 CFG_CMD_JFFS2	| \
-					 CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw"
-
-#define CONFIG_EXTRA_ENV_SETTINGS												\
-	"ramargs=setenv bootargs root=/dev/mtdblock0 rw\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "									\
-	"nfsroot=$(serverip):$(rootpath)\0"											\
-	"addip=setenv bootargs $(bootargs) "										\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"							\
-	":$(hostname):eth0:off\0"													\
-    "ramboot=tftpboot 0x1000000 linux;"											\
-	"run ramargs;run addip;bootelf\0"											\
-	"nfsboot=tftpboot 0x1000000 linux;"											\
-	"run nfsargs;run addip;bootelf\0"											\
-	"flashboot=bootm 0x20100000\0"												\
-	""
-
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Console settings
- *
- */
-
-#define CONFIG_BAUDRATE			57600
-#define CFG_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, 115200 }
-
-#define CFG_PROMPT			"stamp>"	/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE			1024	/* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE			256	/* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE			(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
-#define CFG_MAXARGS			16	/* max number of command args */
-#define CFG_BARGSIZE			CFG_CBSIZE	/* Boot Argument Buffer Size */
-
-#define CONFIG_LOADS_ECHO		1
-
-/*
- * Network settings
- *
- */
-
-#define CONFIG_DRIVER_SMC91111		1
-#define CONFIG_SMC91111_BASE		0x20300300
-/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define HARDCODE_MAC			1 */
-
-/*
- * Flash settings
- *
- */
-
-#define CFG_FLASH_CFI				/* The flash is CFI compatible	*/
-#define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
-#define CFG_FLASH_CFI_AMD_RESET
-
-#define CFG_ENV_IS_IN_FLASH		1
-
-#define CFG_FLASH_BASE			0x20000000
-#define CFG_MAX_FLASH_BANKS		1		/* max number of memory banks */
-#define CFG_MAX_FLASH_SECT		67		/* max number of sectors on one chip */
-
-#define CFG_ENV_ADDR			0x20020000
-#define CFG_ENV_SIZE			0x10000
-#define CFG_ENV_SECT_SIZE		0x10000 /* Total Size of Environment Sector */
-
-#define CFG_FLASH_ERASE_TOUT		30000	/* Timeout for Chip Erase (in ms) */
-#define CFG_FLASH_ERASEBLOCK_TOUT	5000	/* Timeout for Block Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT		1	/* Timeout for Flash Write (in ms) */
-
-/* JFFS Partition offset set  */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS  1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR		11
-
-/*
- * following timeouts shall be used once the
- * Flash real protection is enabled
- */
-#define CFG_FLASH_LOCK_TOUT		5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CFG_FLASH_UNLOCK_TOUT		10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-
-/*
- * I2C settings
- * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
- */
-#define CONFIG_SOFT_I2C			1	/* I2C bit-banged		*/
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PF_SCL				PF3
-#define PF_SDA				PF2
-
-#define I2C_INIT			(*pFIO_DIR |=  PF_SCL); asm("ssync;")
-#define I2C_ACTIVE			(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE			(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ			((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit)			if(bit) { \
-							*pFIO_FLAG_S = PF_SDA; \
-							asm("ssync;"); \
-						} \
-					else	{ \
-							*pFIO_FLAG_C = PF_SDA; \
-							asm("ssync;"); \
-						}
-#define I2C_SCL(bit)			if(bit) { \
-							*pFIO_FLAG_S = PF_SCL; \
-							asm("ssync;"); \
-						} \
-					else	{ \
-							*pFIO_FLAG_C = PF_SCL; \
-							asm("ssync;"); \
-						}
-#define I2C_DELAY			udelay(5)	/* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED			50000
-#define CFG_I2C_SLAVE			0xFE
-
-/*
- * Compact Flash settings
- */
-
-/* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF		1 */
-
-#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
-
-#define CONFIG_MISC_INIT_R		1
-#define CONFIG_DOS_PARTITION		1
-
-/*
- * IDE/ATA stuff
- */
-#undef	CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
-#undef	CONFIG_IDE_LED			/* no led for ide supported */
-#undef	CONFIG_IDE_RESET		/* no reset for ide supported */
-
-#define CFG_IDE_MAXBUS	1		/* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE		(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CFG_ATA_BASE_ADDR		0x20200000
-#define CFG_ATA_IDE0_OFFSET		0x0000
-
-#define CFG_ATA_DATA_OFFSET		0x0020	/* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET		0x0020	/* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET		0x0007	/* Offset for alternate registers */
-
-#define CFG_ATA_STRIDE			2
-#endif
-
-/*
- * SDRAM settings
- *
- */
-
-#define CONFIG_MEM_SIZE			128		/* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH		11	       /* 8, 9, 10, 11	  */
-#define CONFIG_MEM_MT48LC64M4A2FB_7E	1
-
-#define CFG_MEMTEST_START		0x00100000	/* memtest works on */
-#define CFG_MEMTEST_END			0x07EFFFFF	/* 1 ... 127 MB in DRAM */
-#define CFG_LOAD_ADDR			0x01000000	/* default load address */
-
-#define CFG_SDRAM_BASE			0x00000000
-#define CFG_MAX_RAM_SIZE		0x08000000
-
-#define CFG_MONITOR_LEN			(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MONITOR_BASE		(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ			( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ			(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ			( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ			( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ			CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ			CONFIG_CLKIN_HZ
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_HZ				1000		/* 1ms time tick */
-
-#define CFG_MALLOC_LEN			(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MALLOC_BASE			(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE		0x4000
-#define CFG_GBL_DATA_ADDR		(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE		(CFG_GBL_DATA_ADDR  - 4)
-
-#define CFG_LARGE_IMAGE_LEN	0x4000000	/* Large Image Length, set to 64 Meg */
-
-#define CONFIG_SHOW_BOOT_PROGRESS	1	/* Show boot progress on LEDs */
-
-/*
- * Stack sizes
- */
-#define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-
-/*
- * FLASH organization and environment definitions
- */
-#define CFG_BOOTMAPSZ			(8 << 20)	/* Initial Memory map for Linux */
-
-/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
-/*#define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL		(B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL |	\
-				B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
-#define AMBCTL1VAL		(B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL |	\
-				B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
-*/
-#define AMGCTLVAL		0xFF
-#define AMBCTL0VAL		0xBBC3BBC3
-#define AMBCTL1VAL		0x99B39983
-#define CF_AMBCTL1VAL		0x99B3ffc2
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP		0x8
-#define SHT_STRTAB_VDSP		0x1
-#define ELFSHDRSIZE_VDSP	0x2C
-#define VDSP_ENTRY_ADDR		0xFFA00000
-#endif
-
-#endif