diff options
Diffstat (limited to 'include/configs')
40 files changed, 713 insertions, 158 deletions
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h index 8c5a742290..44befe9edf 100644 --- a/include/configs/BC3450.h +++ b/include/configs/BC3450.h @@ -471,13 +471,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) -# define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -# define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -# define CONFIG_SYS_HID0_INIT 0 -# define CONFIG_SYS_HID0_FINAL 0 -#endif +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/EB+MCF-EV123.h b/include/configs/EB+MCF-EV123.h index a0b27a89c4..880cb4ee6b 100644 --- a/include/configs/EB+MCF-EV123.h +++ b/include/configs/EB+MCF-EV123.h @@ -208,6 +208,18 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ + CF_CACR_CEIB | CF_CACR_DBWE | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index 5ef0b7798e..5d3a744fff 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -30,6 +30,7 @@ */ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */ #define CONFIG_ICECUBE 1 /* ... on IceCube board */ #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ @@ -47,7 +48,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ /* * PCI Mapping: * 0x40000000 - 0x4fffffff - PCI Memory @@ -77,10 +77,6 @@ #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 -#else -#define CONFIG_MII 1 -#endif - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -169,7 +165,6 @@ #define CONFIG_BOOTCOMMAND "run flash_self" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ @@ -178,7 +173,6 @@ #else #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif -#endif /* CONFIG_MPC5200 */ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 @@ -338,13 +332,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #if defined(CONFIG_LITE5200B) #define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE diff --git a/include/configs/M5208EVBE.h b/include/configs/M5208EVBE.h index 32123d2f54..e6632acbe7 100644 --- a/include/configs/M5208EVBE.h +++ b/include/configs/M5208EVBE.h @@ -158,7 +158,7 @@ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x40000000 -#define CONFIG_SYS_SDRAM_SIZE 64 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ #define CONFIG_SYS_SDRAM_CFG1 0x43711630 #define CONFIG_SYS_SDRAM_CFG2 0x56670000 #define CONFIG_SYS_SDRAM_CTRL 0xE1002000 @@ -207,6 +207,19 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /* Chipselect bank definitions */ /* * CS0 - NOR Flash diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h index 1801d9d7d5..6c6b5d6d57 100644 --- a/include/configs/M52277EVB.h +++ b/include/configs/M52277EVB.h @@ -302,6 +302,19 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h index 2b816ceae2..5c0dc842aa 100644 --- a/include/configs/M5235EVB.h +++ b/include/configs/M5235EVB.h @@ -237,6 +237,18 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/M5249EVB.h b/include/configs/M5249EVB.h index e3830e5369..33ac2859df 100644 --- a/include/configs/M5249EVB.h +++ b/include/configs/M5249EVB.h @@ -60,6 +60,7 @@ * Command line configuration. */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #undef CONFIG_CMD_NET #define CONFIG_SYS_PROMPT "=> " @@ -165,6 +166,20 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ + CF_ADDRMASK(2) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ + CF_CACR_DBWE) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M5253DEMO.h b/include/configs/M5253DEMO.h index 5e86e4cb90..b5af493b80 100644 --- a/include/configs/M5253DEMO.h +++ b/include/configs/M5253DEMO.h @@ -57,6 +57,7 @@ */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_LOADB #define CONFIG_CMD_LOADS #define CONFIG_CMD_EXT2 @@ -95,11 +96,6 @@ # define DM9000_DATA (CONFIG_DM9000_BASE + 4) # undef CONFIG_DM9000_DEBUG -# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 -# define CONFIG_IPADDR 10.82.121.249 -# define CONFIG_NETMASK 255.255.252.0 -# define CONFIG_SERVERIP 10.82.120.80 -# define CONFIG_GATEWAYIP 10.82.123.254 # define CONFIG_OVERWRITE_ETHADDR_ONCE # define CONFIG_EXTRA_ENV_SETTINGS \ @@ -109,9 +105,9 @@ "u-boot=u-boot.bin\0" \ "load=tftp ${loadaddr) ${u-boot}\0" \ "upd=run load; run prog\0" \ - "prog=prot off 0 2ffff;" \ - "era 0 2ffff;" \ - "cp.b ${loadaddr} 0 ${filesize};" \ + "prog=prot off 0xff800000 0xff82ffff;" \ + "era 0xff800000 0xff82ffff;" \ + "cp.b ${loadaddr} 0xff800000 ${filesize};" \ "save\0" \ "" #endif @@ -231,6 +227,20 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ + CF_ADDRMASK(8) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ + CF_CACR_DBWE) + /* Port configuration */ #define CONFIG_SYS_FECI2C 0xF0 diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h index df6970cdfa..206d1152ee 100644 --- a/include/configs/M5253EVBE.h +++ b/include/configs/M5253EVBE.h @@ -64,6 +64,7 @@ * Command line configuration. */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #undef CONFIG_CMD_NET #define CONFIG_CMD_LOADB #define CONFIG_CMD_LOADS @@ -179,6 +180,20 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ + CF_ADDRMASK(2) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ + CF_CACR_DBWE) + /* Port configuration */ #define CONFIG_SYS_FECI2C 0xF0 diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h index 50b3ab2808..798949cc56 100644 --- a/include/configs/M5271EVB.h +++ b/include/configs/M5271EVB.h @@ -72,6 +72,7 @@ */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING #define CONFIG_CMD_NET #define CONFIG_CMD_MII @@ -229,6 +230,19 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /* Chip Select 0 : Boot Flash */ #define CONFIG_SYS_CS0_BASE 0xFFE00000 #define CONFIG_SYS_CS0_MASK 0x001F0001 diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h index f824158a69..f704bb3ff7 100644 --- a/include/configs/M5272C3.h +++ b/include/configs/M5272C3.h @@ -74,6 +74,7 @@ */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_CMD_PING @@ -211,6 +212,19 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h index b380159812..981670ac06 100644 --- a/include/configs/M5275EVB.h +++ b/include/configs/M5275EVB.h @@ -72,6 +72,7 @@ /* Available command configuration */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_PING #define CONFIG_CMD_MII #define CONFIG_CMD_NET @@ -121,11 +122,6 @@ #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0) #define CONFIG_SYS_I2C_PINMUX_SET (0x000F) -#ifdef CONFIG_MCFFEC -#define CONFIG_ETHADDR 00:06:3b:01:41:55 -#define CONFIG_ETH1ADDR 00:0e:0c:bc:e5:60 -#endif - #define CONFIG_SYS_PROMPT "-> " #define CONFIG_SYS_LONGHELP /* undef to save memory */ @@ -145,6 +141,23 @@ #define CONFIG_SYS_MEMTEST_START 0x400 #define CONFIG_SYS_MEMTEST_END 0x380000 +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_RETRY_COUNT 5 +# define CONFIG_OVERWRITE_ETHADDR_ONCE +#endif /* FEC_ENET */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "uboot=u-boot.bin\0" \ + "load=tftp ${loadaddr} ${uboot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" + #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CLK 150000000 @@ -208,6 +221,19 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h index 15590cfcd5..6e0aa14d3a 100644 --- a/include/configs/M5282EVB.h +++ b/include/configs/M5282EVB.h @@ -64,6 +64,7 @@ * Command line configuration. */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_MII @@ -209,6 +210,18 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ + CF_CACR_CEIB | CF_CACR_DBWE | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M53017EVB.h b/include/configs/M53017EVB.h index 30855bdaa2..d983a8fedb 100644 --- a/include/configs/M53017EVB.h +++ b/include/configs/M53017EVB.h @@ -69,6 +69,8 @@ # define CONFIG_MII_INIT 1 # define CONFIG_SYS_DISCOVER_PHY # define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_TX_ETH_BUFFER 8 +# define CONFIG_SYS_FEC_BUF_USE_SRAM # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # define CONFIG_HAS_ETH1 @@ -166,7 +168,7 @@ */ #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 #define CONFIG_SYS_INIT_RAM_END 0x20000 /* End of used area in internal SRAM */ -#define CONFIG_SYS_INIT_RAM_CTRL 0x21 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) - 0x10) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET @@ -180,7 +182,7 @@ #define CONFIG_SYS_SDRAM_SIZE 64 /* SDRAM size in MB */ #define CONFIG_SYS_SDRAM_CFG1 0x43711630 #define CONFIG_SYS_SDRAM_CFG2 0x56670000 -#define CONFIG_SYS_SDRAM_CTRL 0xE1002000 +#define CONFIG_SYS_SDRAM_CTRL 0xE1092000 #define CONFIG_SYS_SDRAM_EMOD 0x80010000 #define CONFIG_SYS_SDRAM_MODE 0x00CD0000 @@ -231,6 +233,17 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ + CF_CACR_DCM_P) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index 8180c05e67..159b178f40 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -237,6 +237,17 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ + CF_CACR_DCM_P) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h index 8652a80aa1..af1988ce0a 100644 --- a/include/configs/M5373EVB.h +++ b/include/configs/M5373EVB.h @@ -237,6 +237,17 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ + CF_CACR_DCM_P) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h index a5acfd2846..a80d33047f 100644 --- a/include/configs/M54451EVB.h +++ b/include/configs/M54451EVB.h @@ -309,6 +309,21 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 7737284aab..5b4bba8c26 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -279,7 +279,7 @@ * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 -#define CONFIG_SYS_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) - 32) @@ -408,6 +408,21 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h index 4534002e47..d0077667f3 100644 --- a/include/configs/M5475EVB.h +++ b/include/configs/M5475EVB.h @@ -286,6 +286,22 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ + CF_CACR_IDCM) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ + CF_CACR_IEC | CF_CACR_ICINVA) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h index 971cb67bad..f23b8b0efa 100644 --- a/include/configs/M5485EVB.h +++ b/include/configs/M5485EVB.h @@ -272,6 +272,22 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ + CF_CACR_IDCM) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ + CF_CACR_IEC | CF_CACR_ICINVA) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + /*----------------------------------------------------------------------- * Chipselect bank definitions */ diff --git a/include/configs/PM520.h b/include/configs/PM520.h index f9687d2743..22de2075f9 100644 --- a/include/configs/PM520.h +++ b/include/configs/PM520.h @@ -50,7 +50,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ /* * PCI Mapping: * 0x40000000 - 0x4fffffff - PCI Memory @@ -75,7 +74,6 @@ #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #undef CONFIG_NS8382X -#endif /* Partitions */ #define CONFIG_DOS_PARTITION @@ -111,9 +109,7 @@ #define CONFIG_CMD_SNTP #define CONFIG_CMD_USB -#if defined(CONFIG_MPC5200) #define CONFIG_CMD_PCI -#endif /* @@ -147,12 +143,10 @@ #define CONFIG_BOOTCOMMAND "run flash_self" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif /* * I2C configuration */ @@ -301,13 +295,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #if defined(CONFIG_BOOT_ROM) #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_BOOTROM_BASE diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h index 25f3a26f35..b69f015c7c 100644 --- a/include/configs/TASREG.h +++ b/include/configs/TASREG.h @@ -252,6 +252,17 @@ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ + CF_CACR_DBWE) + /*----------------------------------------------------------------------- * Memory bank definitions */ diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h index 3438abaeaa..6da18ebca1 100644 --- a/include/configs/TB5200.h +++ b/include/configs/TB5200.h @@ -430,13 +430,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 2154c7870e..107bff19ff 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -633,13 +633,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h index 1daa5746ee..7510ab10e4 100644 --- a/include/configs/Total5200.h +++ b/include/configs/Total5200.h @@ -41,6 +41,7 @@ */ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */ #define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ @@ -73,7 +74,6 @@ #define CONFIG_SPLASH_SCREEN -#ifdef CONFIG_MPC5200 /* MGT5100 PCI is not supported yet. */ /* * PCI Mapping: * 0x40000000 - 0x4fffffff - PCI Memory @@ -98,12 +98,6 @@ #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 -#else /* MGT5100 */ - -#define CONFIG_MII 1 - -#endif - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -127,9 +121,7 @@ */ #include <config_cmd_default.h> -#if defined(CONFIG_MPC5200) - #define CONFIG_CMD_PCI -#endif +#define CONFIG_CMD_PCI #define CONFIG_CMD_BMP #define CONFIG_CMD_EEPROM @@ -176,12 +168,10 @@ #define CONFIG_BOOTCOMMAND "run flash_self" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif /* * I2C configuration @@ -326,17 +316,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif - -#if defined (CONFIG_MGT5100) -# define CONFIG_BOARD_EARLY_INIT_R /* switch from CS_BOOT to CS0 */ -#endif #if CONFIG_TOTAL5200_REV==1 # define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE diff --git a/include/configs/aev.h b/include/configs/aev.h index 2b4826d90e..98958a6237 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -362,13 +362,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h new file mode 100644 index 0000000000..7c8281cae7 --- /dev/null +++ b/include/configs/astro_mcf5373l.h @@ -0,0 +1,400 @@ +/* + * Configuration settings for the Sentec Cobra Board. + * + * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * configuration for ASTRO "Urmel" board. + * Originating from Cobra5272 configuration, messed up by + * Wolfgang Wegner <w.wegner@astro-kom.de> + * Please do not bother the original author with bug reports + * concerning this file. + */ + +#ifndef _CONFIG_ASTRO_MCF5373L_H +#define _CONFIG_ASTRO_MCF5373L_H + +/* + * set the card type to actually compile for; either of + * the possibilities listed below has to be used! + */ +#define CONFIG_ASTRO_V532 1 + +#if CONFIG_ASTRO_V532 +#define ASTRO_ID 0xF8 +#elif CONFIG_ASTRO_V512 +#define ASTRO_ID 0xFA +#elif CONFIG_ASTRO_TWIN7S2 +#define ASTRO_ID 0xF9 +#elif CONFIG_ASTRO_V912 +#define ASTRO_ID 0xFC +#elif CONFIG_ASTRO_COFDMDUOS2 +#define ASTRO_ID 0xFB +#else +#error No card type defined! +#endif + +/* + * Define processor + * possible values for Urmel board: only Coldfire M5373 processor supported + * (please do not change) + */ + +/* it seems not clear yet which processor defines we should use */ +#define CONFIG_MCF537x /* define processor family */ +#define CONFIG_MCF532x /* define processor family */ +#define CONFIG_M5373 /* define processor type */ +#define CONFIG_ASTRO5373L /* define board type */ + +/* Command line configuration */ +#include <config_cmd_default.h> + +/* + * CONFIG_MK_RAM defines if u-boot is loaded via BDM (or started from + * a different bootloader that has already performed RAM setup) or + * started directly from flash, which is the regular case for production + * boards. + */ +#ifdef CONFIG_MK_RAM +#define CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_TEXT_BASE 0x40020000 +#define ENABLE_JFFS 0 +#else +#define CONFIG_TEXT_BASE 0x00000000 +#define ENABLE_JFFS 1 +#endif + +/* Define which commmands should be available at u-boot command prompt */ + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_MISC +#define CONFIG_CMD_XIMG +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS +#if ENABLE_JFFS +#define CONFIG_CMD_JFFS2 +#endif +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_LOADS +#define CONFIG_CMD_LOADB +#define CONFIG_CMD_FPGA +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_MCFRTC +#undef RTC_DEBUG + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* I2C */ +#define CONFIG_FSL_I2C +#define CONFIG_HARD_I2C /* I2C with hw support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SPEED 80000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR + +/* + * Defines processor clock - important for correct timings concerning serial + * interface etc. + * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms + */ + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 80000000 +#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3) +#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ + +#define CONFIG_SYS_CORE_SRAM_SIZE 0x8000 +#define CONFIG_SYS_CORE_SRAM 0x80000000 + +#define CONFIG_SYS_UNIFY_CACHE + +/* + * Define baudrate for UART1 (console output, tftp, ...) + * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud + * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected + * in u-boot command interface + */ + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (2) +#define CONFIG_SYS_UART2_ALT3_GPIO + +/* + * Watchdog configuration; Watchdog is disabled for running from RAM + * and set to highest possible value else. Beware there is no check + * in the watchdog code to validate the timeout value set here! + */ + +#ifndef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_WATCHDOG +#define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */ +#endif + +/* + * Configuration for environment + * Environment is located in the last sector of the flash + */ + +#ifndef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_ENV_OFFSET 0x1FF8000 +#define CONFIG_ENV_SECT_SIZE 0x8000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#else +/* + * environment in RAM - This is used to use a single PC-based application + * to load an image, load U-Boot, load an environment and then start U-Boot + * to execute the commands from the environment. Feedback is done via setting + * and reading memory locations. + */ +#define CONFIG_ENV_ADDR 0x40060000 +#define CONFIG_ENV_SECT_SIZE 0x8000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#endif + +/* here we put our FPGA configuration... */ +#define CONFIG_MISC_INIT_R 1 + +/* Define user parameters that have to be customized most likely */ + +/* AUTOBOOT settings - booting images automatically by u-boot after power on */ + +/* + * used for autoboot, delay in seconds u-boot will wait before starting + * defined (auto-)boot command, setting to -1 disables delay, setting to + * 0 will too prevent access to u-boot command interface: u-boot then has + * to be reflashed + * beware - watchdog is not serviced during autoboot delay time! + */ +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_BOOTDELAY 1 +#else +#define CONFIG_BOOTDELAY 1 +#endif + +/* + * The following settings will be contained in the environment block ; if you + * want to use a neutral environment all those settings can be manually set in + * u-boot: 'set' command + */ + +#define _QUOTEME(x) #x +#define QUOTEME(x) _QUOTEME(x) + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loaderversion=11\0" \ + "card_id="QUOTEME(ASTRO_ID)"\0" \ + "alterafile=0\0" \ + "xilinxfile=0\0" \ + "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ + "fpga load 0 0x41000000 $filesize\0" \ + "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ + "fpga load 1 0x41000000 $filesize\0" \ + "env_default=1\0" \ + "env_check=if test $env_default -eq 1;"\ + " then setenv env_default 0;saveenv;fi\0" + +/* + * "update" is a non-standard command that has to be supplied + * by external update.c; This is not included in mainline because + * it needs non-blocking CFI routines. + */ +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */ +#else +#if CONFIG_ASTRO_V532 +#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ + "run xilinxload&&run alteraload&&bootm 0x80000;"\ + "update;reset" +#else +#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ + "run xilinxload&&bootm 0x80000;update;reset" +#endif +#endif + +/* default bootargs that are considered during boot */ +#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\ + " loaderversion=$loaderversion" + +#define CONFIG_SYS_PROMPT "URMEL > " + +/* default RAM address for user programs */ +#define CONFIG_SYS_LOAD_ADDR 0x20000 + +#define CONFIG_SYS_LONGHELP + +#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 +#else +#define CONFIG_SYS_CBSIZE 256 +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_FPGA_COUNT 1 +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_SPARTAN3 +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_CYCLON2 +#define CONFIG_SYS_FPGA_PROG_FEEDBACK +#define CONFIG_SYS_FPGA_WAIT 1000 + +/* End of user parameters to be customized */ + +/* Defines memory range for test */ + +#define CONFIG_SYS_MEMTEST_START 0x40020000 +#define CONFIG_SYS_MEMTEST_END 0x41ffffff + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/* Base register address */ + +#define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */ + +/* System Conf. Reg. & System Protection Reg. */ + +#define CONFIG_SYS_SCR 0x0003; +#define CONFIG_SYS_SPR 0xffff; + +/* + * Definitions for initial stack pointer and data area (in internal SRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +#define CONFIG_SYS_INIT_RAM_END 0x8000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_SIZE 128 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 + */ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 + +/* + * Chipselect bank definitions + * + * CS0 - Flash 32MB (first 16MB) + * CS1 - Flash 32MB (second half) + * CS2 - FPGA + * CS3 - FPGA + * CS4 - unused + * CS5 - unused + */ +#define CONFIG_SYS_CS0_BASE 0 +#define CONFIG_SYS_CS0_MASK 0x00ff0001 +#define CONFIG_SYS_CS0_CTRL 0x00001fc0 + +#define CONFIG_SYS_CS1_BASE 0x01000000 +#define CONFIG_SYS_CS1_MASK 0x00ff0001 +#define CONFIG_SYS_CS1_CTRL 0x00001fc0 + +#define CONFIG_SYS_CS2_BASE 0x20000000 +#define CONFIG_SYS_CS2_MASK 0x00ff0001 +#define CONFIG_SYS_CS2_CTRL 0x0000fec0 + +#define CONFIG_SYS_CS3_BASE 0x21000000 +#define CONFIG_SYS_CS3_MASK 0x00ff0001 +#define CONFIG_SYS_CS3_CTRL 0x0000fec0 + +#define CONFIG_SYS_FLASH_BASE 0x00000000 + +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_SYS_MONITOR_BASE CONFIG_TEXT_BASE +#else +/* This is mainly used during relocation in start.S */ +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* FLASH organization */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 259 +#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 + +#define CONFIG_SYS_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_SIZE 0x2000000 +#define CONFIG_SYS_FLASH_PROTECTION 1 +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 +#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1 + +#if ENABLE_JFFS +/* JFFS Partition offset set */ +#define CONFIG_SYS_JFFS2_FIRST_BANK 0 +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 +/* 512k reserved for u-boot */ +#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40 +#endif + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 + +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ + CF_CACR_DCM_P) + +#endif /* _CONFIG_ASTRO_MCF5373L_H */ diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index 1c3ea23c77..330e3ac667 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -331,6 +331,19 @@ from which user programs will be started */ */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /*----------------------------------------------------------------------- * Memory bank definitions * diff --git a/include/configs/cpci5200.h b/include/configs/cpci5200.h index 52df16af14..f7290d6eb4 100644 --- a/include/configs/cpci5200.h +++ b/include/configs/cpci5200.h @@ -59,7 +59,6 @@ #define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ /* * PCI Mapping: * 0x40000000 - 0x4fffffff - PCI Memory @@ -90,8 +89,6 @@ #define CONFIG_NS8382X 1 #endif -#endif - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -169,8 +166,6 @@ #define CONFIG_BOOTCOMMAND "run flash_vxworks0" -#if defined(CONFIG_MPC5200) - #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ #define CONFIG_SYS_NVRAM_BASE_ADDR 0xfd010000 #define CONFIG_SYS_NVRAM_SIZE 32*1024 @@ -179,7 +174,6 @@ * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif /* * I2C configuration */ @@ -303,13 +297,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h index a81527ebed..f9cdcbc3ce 100644 --- a/include/configs/hmi1001.h +++ b/include/configs/hmi1001.h @@ -261,13 +261,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/idmr.h b/include/configs/idmr.h index 841affb7cc..61e3bad4f3 100644 --- a/include/configs/idmr.h +++ b/include/configs/idmr.h @@ -224,6 +224,19 @@ /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + /* Port configuration */ #define CONFIG_SYS_FECI2C 0xF0 diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index 14f7826705..c5b1565e34 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -366,13 +366,8 @@ static inline void tws_data_config_output(unsigned output) /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h index d0cb1e1d60..6903b36146 100644 --- a/include/configs/ipek01.h +++ b/include/configs/ipek01.h @@ -324,13 +324,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h index b29ef9b655..d25e093ac6 100644 --- a/include/configs/manroland/mpc5200-common.h +++ b/include/configs/manroland/mpc5200-common.h @@ -170,13 +170,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/mecp5200.h b/include/configs/mecp5200.h index 4a93b58885..73405eabb9 100644 --- a/include/configs/mecp5200.h +++ b/include/configs/mecp5200.h @@ -63,9 +63,6 @@ #endif #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ - #define CONFIG_MII #if 0 /* test-only !!! */ #define CONFIG_NET_MULTI 1 @@ -74,10 +71,6 @@ #define CONFIG_NS8382X 1 #endif -#else /* MPC5100 */ - -#endif - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -152,12 +145,10 @@ #define CONFIG_BOOTCOMMAND "run flash_vxworks0" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */ -#endif /* * I2C configuration */ @@ -288,13 +279,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/o2dnt.h b/include/configs/o2dnt.h index 18e7cc2a9c..bdc0f7944a 100644 --- a/include/configs/o2dnt.h +++ b/include/configs/o2dnt.h @@ -138,7 +138,6 @@ #define CONFIG_BOOTCOMMAND "run flash_self" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ @@ -154,7 +153,6 @@ */ #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif -#endif /* * I2C configuration @@ -276,13 +274,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h index 8ca55d78ec..80a0bc609a 100644 --- a/include/configs/pf5200.h +++ b/include/configs/pf5200.h @@ -61,7 +61,6 @@ #endif #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */ /* * PCI Mapping: * 0x40000000 - 0x4fffffff - PCI Memory @@ -87,7 +86,6 @@ #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 #endif -#endif /* Partitions */ #define CONFIG_MAC_PARTITION @@ -121,9 +119,7 @@ #define CONFIG_CMD_I2C #define CONFIG_CMD_IDE -#ifdef CONFIG_MPC5200 #define CONFIG_CMD_PCI -#endif #if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ @@ -166,12 +162,10 @@ #define CONFIG_BOOTCOMMAND "run flash_vxworks0" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif /* * I2C configuration */ @@ -289,13 +283,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h index 5a2ef3aa8c..060026bb64 100644 --- a/include/configs/smmaco4.h +++ b/include/configs/smmaco4.h @@ -358,13 +358,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/spieval.h b/include/configs/spieval.h index 27dda253fb..d377e199d8 100644 --- a/include/configs/spieval.h +++ b/include/configs/spieval.h @@ -438,13 +438,8 @@ /* * Various low-level settings */ -#if defined(CONFIG_MPC5200) #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE -#else -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL 0 -#endif #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE diff --git a/include/configs/v38b.h b/include/configs/v38b.h index 92bcdb33fb..d462ed0f1e 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -170,12 +170,10 @@ #define CONFIG_BOOTCOMMAND "run net_nfs" -#if defined(CONFIG_MPC5200) /* * IPB Bus clocking configuration. */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif /* * I2C configuration |