diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/km8309-common.h | 174 | ||||
| -rw-r--r-- | include/configs/km8321-common.h | 139 | ||||
| -rw-r--r-- | include/configs/kmtegr1.h | 164 | ||||
| -rw-r--r-- | include/configs/kmvect1.h | 164 | ||||
| -rw-r--r-- | include/configs/suvd3.h | 116 | ||||
| -rw-r--r-- | include/configs/tuxx1.h | 115 |
6 files changed, 551 insertions, 321 deletions
diff --git a/include/configs/km8309-common.h b/include/configs/km8309-common.h deleted file mode 100644 index 3bd334c515..0000000000 --- a/include/configs/km8309-common.h +++ /dev/null @@ -1,174 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 Keymile AG - * Gerlando Falauto <gerlando.falauto@keymile.com> - * - * Based on km8321-common.h, see respective copyright notice for credits - */ - -#ifndef __CONFIG_KM8309_COMMON_H -#define __CONFIG_KM8309_COMMON_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" - -/* include common defines/options for all 83xx Keymile boards */ -#include "km83xx-common.h" - -/* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FMAN_FW_IN_NOR -/* between the u-boot partition and env */ -#ifndef CONFIG_SYS_QE_FW_ADDR -#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 -#endif - -/* - * System IO Config - */ -/* 0x14000180 SICR_1 */ -#define CONFIG_SYS_SICRL (0 \ - | SICR_1_UART1_UART1RTS \ - | SICR_1_I2C_CKSTOP \ - | SICR_1_IRQ_A_IRQ \ - | SICR_1_IRQ_B_IRQ \ - | SICR_1_GPIO_A_GPIO \ - | SICR_1_GPIO_B_GPIO \ - | SICR_1_GPIO_C_GPIO \ - | SICR_1_GPIO_D_GPIO \ - | SICR_1_GPIO_E_GPIO \ - | SICR_1_GPIO_F_GPIO \ - | SICR_1_USB_A_UART2S \ - | SICR_1_USB_B_UART2RTS \ - | SICR_1_FEC1_FEC1 \ - | SICR_1_FEC2_FEC2 \ - ) - -/* 0x00080400 SICR_2 */ -#define CONFIG_SYS_SICRH (0 \ - | SICR_2_FEC3_FEC3 \ - | SICR_2_HDLC1_A_HDLC1 \ - | SICR_2_ELBC_A_LA \ - | SICR_2_ELBC_B_LCLK \ - | SICR_2_HDLC2_A_HDLC2 \ - | SICR_2_USB_D_GPIO \ - | SICR_2_PCI_PCI \ - | SICR_2_HDLC1_B_HDLC1 \ - | SICR_2_HDLC1_C_HDLC1 \ - | SICR_2_HDLC2_B_GPIO \ - | SICR_2_HDLC2_C_HDLC2 \ - | SICR_2_QUIESCE_B \ - ) - -/* GPR_1 */ -#define CONFIG_SYS_GPR1 0x50008060 - -#define CONFIG_SYS_GP1DIR 0x00000000 -#define CONFIG_SYS_GP1ODR 0x00000000 -#define CONFIG_SYS_GP2DIR 0xFF000000 -#define CONFIG_SYS_GP2ODR 0x00000000 - -/* - * Hardware Reset Configuration Word - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ - HRCWL_DDR_TO_SCB_CLK_2X1 | \ - HRCWL_CSB_TO_CLKIN_2X1 | \ - HRCWL_CORE_TO_CSB_2X1 | \ - HRCWL_CE_PLL_VCO_DIV_2 | \ - HRCWL_CE_TO_PLL_1X3) - -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_AGENT | \ - HRCWH_PCI_ARBITER_DISABLE | \ - HRCWH_CORE_ENABLE | \ - HRCWH_FROM_0X00000100 | \ - HRCWH_BOOTSEQ_DISABLE | \ - HRCWH_SW_WATCHDOG_DISABLE | \ - HRCWH_ROM_LOC_LOCAL_16BIT | \ - HRCWH_BIG_ENDIAN | \ - HRCWH_LALE_NORMAL) - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_RD_NEVER | \ - CSCONFIG_ODT_WR_ONLY_CURRENT | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP 0x80000000 -#define CONFIG_SYS_LCRR_EADC 0x00010000 -#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 - -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * MMU Setup - */ -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U - -#endif /* __CONFIG_KM8309_COMMON_H */ diff --git a/include/configs/km8321-common.h b/include/configs/km8321-common.h deleted file mode 100644 index a121a445f7..0000000000 --- a/include/configs/km8321-common.h +++ /dev/null @@ -1,139 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2006 Freescale Semiconductor, Inc. - * Dave Liu <daveliu@freescale.com> - * - * Copyright (C) 2007 Logic Product Development, Inc. - * Peter Barada <peterb@logicpd.com> - * - * Copyright (C) 2007 MontaVista Software, Inc. - * Anton Vorontsov <avorontsov@ru.mvista.com> - * - * (C) Copyright 2008 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * (C) Copyright 2010 - * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com - * - * (C) Copyright 2010-2011 - * Thomas Reufer, KEYMILE Ltd, thomas.reufer@keymile.com - */ - -#ifndef __CONFIG_KM8321_COMMON_H -#define __CONFIG_KM8321_COMMON_H - -/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - -/* include common defines/options for all 83xx Keymile boards */ -#include "km83xx-common.h" - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -/* - * Hardware Reset Configuration Word - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ - HRCWL_DDR_TO_SCB_CLK_2X1 | \ - HRCWL_CSB_TO_CLKIN_2X1 | \ - HRCWL_CORE_TO_CSB_2_5X1 | \ - HRCWL_CE_PLL_VCO_DIV_2 | \ - HRCWL_CE_TO_PLL_1X3) - -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_AGENT | \ - HRCWH_PCI_ARBITER_DISABLE | \ - HRCWH_CORE_ENABLE | \ - HRCWH_FROM_0X00000100 | \ - HRCWH_BOOTSEQ_DISABLE | \ - HRCWH_SW_WATCHDOG_DISABLE | \ - HRCWH_ROM_LOC_LOCAL_16BIT | \ - HRCWH_BIG_ENDIAN | \ - HRCWH_LALE_NORMAL) - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP 0x80000000 -#define CONFIG_SYS_LCRR_EADC 0x00010000 -#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 - -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * MMU Setup - */ -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U - -#endif /* __CONFIG_KM8321_COMMON_H */ diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h index 95a131892d..27e3905c2b 100644 --- a/include/configs/kmtegr1.h +++ b/include/configs/kmtegr1.h @@ -35,8 +35,168 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 -/* include common defines/options for all 8309 Keymile boards */ -#include "km8309-common.h" +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ + +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" + +/* include common defines/options for all 83xx Keymile boards */ +#include "km83xx-common.h" + +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +/* between the u-boot partition and env */ +#ifndef CONFIG_SYS_QE_FW_ADDR +#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 +#endif + +/* + * System IO Config + */ +/* 0x14000180 SICR_1 */ +#define CONFIG_SYS_SICRL (0 \ + | SICR_1_UART1_UART1RTS \ + | SICR_1_I2C_CKSTOP \ + | SICR_1_IRQ_A_IRQ \ + | SICR_1_IRQ_B_IRQ \ + | SICR_1_GPIO_A_GPIO \ + | SICR_1_GPIO_B_GPIO \ + | SICR_1_GPIO_C_GPIO \ + | SICR_1_GPIO_D_GPIO \ + | SICR_1_GPIO_E_GPIO \ + | SICR_1_GPIO_F_GPIO \ + | SICR_1_USB_A_UART2S \ + | SICR_1_USB_B_UART2RTS \ + | SICR_1_FEC1_FEC1 \ + | SICR_1_FEC2_FEC2 \ + ) + +/* 0x00080400 SICR_2 */ +#define CONFIG_SYS_SICRH (0 \ + | SICR_2_FEC3_FEC3 \ + | SICR_2_HDLC1_A_HDLC1 \ + | SICR_2_ELBC_A_LA \ + | SICR_2_ELBC_B_LCLK \ + | SICR_2_HDLC2_A_HDLC2 \ + | SICR_2_USB_D_GPIO \ + | SICR_2_PCI_PCI \ + | SICR_2_HDLC1_B_HDLC1 \ + | SICR_2_HDLC1_C_HDLC1 \ + | SICR_2_HDLC2_B_GPIO \ + | SICR_2_HDLC2_C_HDLC2 \ + | SICR_2_QUIESCE_B \ + ) + +/* GPR_1 */ +#define CONFIG_SYS_GPR1 0x50008060 + +#define CONFIG_SYS_GP1DIR 0x00000000 +#define CONFIG_SYS_GP1ODR 0x00000000 +#define CONFIG_SYS_GP2DIR 0xFF000000 +#define CONFIG_SYS_GP2ODR 0x00000000 + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ + HRCWL_DDR_TO_SCB_CLK_2X1 | \ + HRCWL_CSB_TO_CLKIN_2X1 | \ + HRCWL_CORE_TO_CSB_2X1 | \ + HRCWL_CE_PLL_VCO_DIV_2 | \ + HRCWL_CE_TO_PLL_1X3) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_AGENT | \ + HRCWH_PCI_ARBITER_DISABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE | \ + HRCWH_SW_WATCHDOG_DISABLE | \ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_NORMAL) + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_RD_NEVER | \ + CSCONFIG_ODT_WR_ONLY_CURRENT | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP 0x80000000 +#define CONFIG_SYS_LCRR_EADC 0x00010000 +#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 + +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * MMU Setup + */ +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + /* must be after the include because KMBEC_FPGA is otherwise undefined */ #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */ diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h index 0bbf541aec..5a0fbccade 100644 --- a/include/configs/kmvect1.h +++ b/include/configs/kmvect1.h @@ -26,8 +26,168 @@ #define CONFIG_KM_BOARD_NAME "kmvect1" /* at end of uboot partition, before env */ #define CONFIG_SYS_QE_FW_ADDR 0xF00B0000 -/* include common defines/options for all 8309 Keymile boards */ -#include "km8309-common.h" + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ + +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" + +/* include common defines/options for all 83xx Keymile boards */ +#include "km83xx-common.h" + +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +/* between the u-boot partition and env */ +#ifndef CONFIG_SYS_QE_FW_ADDR +#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 +#endif + +/* + * System IO Config + */ +/* 0x14000180 SICR_1 */ +#define CONFIG_SYS_SICRL (0 \ + | SICR_1_UART1_UART1RTS \ + | SICR_1_I2C_CKSTOP \ + | SICR_1_IRQ_A_IRQ \ + | SICR_1_IRQ_B_IRQ \ + | SICR_1_GPIO_A_GPIO \ + | SICR_1_GPIO_B_GPIO \ + | SICR_1_GPIO_C_GPIO \ + | SICR_1_GPIO_D_GPIO \ + | SICR_1_GPIO_E_GPIO \ + | SICR_1_GPIO_F_GPIO \ + | SICR_1_USB_A_UART2S \ + | SICR_1_USB_B_UART2RTS \ + | SICR_1_FEC1_FEC1 \ + | SICR_1_FEC2_FEC2 \ + ) + +/* 0x00080400 SICR_2 */ +#define CONFIG_SYS_SICRH (0 \ + | SICR_2_FEC3_FEC3 \ + | SICR_2_HDLC1_A_HDLC1 \ + | SICR_2_ELBC_A_LA \ + | SICR_2_ELBC_B_LCLK \ + | SICR_2_HDLC2_A_HDLC2 \ + | SICR_2_USB_D_GPIO \ + | SICR_2_PCI_PCI \ + | SICR_2_HDLC1_B_HDLC1 \ + | SICR_2_HDLC1_C_HDLC1 \ + | SICR_2_HDLC2_B_GPIO \ + | SICR_2_HDLC2_C_HDLC2 \ + | SICR_2_QUIESCE_B \ + ) + +/* GPR_1 */ +#define CONFIG_SYS_GPR1 0x50008060 + +#define CONFIG_SYS_GP1DIR 0x00000000 +#define CONFIG_SYS_GP1ODR 0x00000000 +#define CONFIG_SYS_GP2DIR 0xFF000000 +#define CONFIG_SYS_GP2ODR 0x00000000 + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ + HRCWL_DDR_TO_SCB_CLK_2X1 | \ + HRCWL_CSB_TO_CLKIN_2X1 | \ + HRCWL_CORE_TO_CSB_2X1 | \ + HRCWL_CE_PLL_VCO_DIV_2 | \ + HRCWL_CE_TO_PLL_1X3) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_AGENT | \ + HRCWH_PCI_ARBITER_DISABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE | \ + HRCWH_SW_WATCHDOG_DISABLE | \ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_NORMAL) + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_RD_NEVER | \ + CSCONFIG_ODT_WR_ONLY_CURRENT | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP 0x80000000 +#define CONFIG_SYS_LCRR_EADC 0x00010000 +#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 + +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * MMU Setup + */ +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #define CONFIG_SYS_APP1_BASE 0xA0000000 #define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */ diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h index 98137392ed..5fe5f3cc23 100644 --- a/include/configs/suvd3.h +++ b/include/configs/suvd3.h @@ -24,8 +24,120 @@ #define CONFIG_HOSTNAME "suvd3" #define CONFIG_KM_BOARD_NAME "suvd3" -/* include common defines/options for all 8321 Keymile boards */ -#include "km8321-common.h" + +/* + * High Level Configuration Options + */ +#define CONFIG_QE /* Has QE */ +#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ + +#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" + +/* include common defines/options for all 83xx Keymile boards */ +#include "km83xx-common.h" + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRL SICRL_IRQ_CKS + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ + HRCWL_DDR_TO_SCB_CLK_2X1 | \ + HRCWL_CSB_TO_CLKIN_2X1 | \ + HRCWL_CORE_TO_CSB_2_5X1 | \ + HRCWL_CE_PLL_VCO_DIV_2 | \ + HRCWL_CE_TO_PLL_1X3) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_AGENT | \ + HRCWH_PCI_ARBITER_DISABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE | \ + HRCWH_SW_WATCHDOG_DISABLE | \ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_NORMAL) + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_WR_CFG | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP 0x80000000 +#define CONFIG_SYS_LCRR_EADC 0x00010000 +#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 + +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * MMU Setup + */ +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #define CONFIG_SYS_APP1_BASE 0xA0000000 #define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */ diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h index 0b17084b05..c031661830 100644 --- a/include/configs/tuxx1.h +++ b/include/configs/tuxx1.h @@ -42,8 +42,119 @@ #error ("Board not supported") #endif -/* include common defines/options for all 8321 Keymile boards */ -#include "km8321-common.h" +/* + * High Level Configuration Options + */ +#define CONFIG_QE /* Has QE */ +#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ + +#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" + +/* include common defines/options for all 83xx Keymile boards */ +#include "km83xx-common.h" + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRL SICRL_IRQ_CKS + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \ + HRCWL_DDR_TO_SCB_CLK_2X1 | \ + HRCWL_CSB_TO_CLKIN_2X1 | \ + HRCWL_CORE_TO_CSB_2_5X1 | \ + HRCWL_CE_PLL_VCO_DIV_2 | \ + HRCWL_CE_TO_PLL_1X3) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_AGENT | \ + HRCWH_PCI_ARBITER_DISABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE | \ + HRCWH_SW_WATCHDOG_DISABLE | \ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_NORMAL) + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_WR_CFG | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP 0x80000000 +#define CONFIG_SYS_LCRR_EADC 0x00010000 +#define CONFIG_SYS_LCRR_CLKDIV 0x00000002 + +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * MMU Setup + */ +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #define CONFIG_SYS_APP1_BASE 0xA0000000 /* PAXG */ #define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */ |