diff options
Diffstat (limited to 'include')
62 files changed, 1280 insertions, 134 deletions
diff --git a/include/asm-arm/arch-davinci/emif_defs.h b/include/asm-arm/arch-davinci/emif_defs.h index 646fc77469..c91e30c8fc 100644 --- a/include/asm-arm/arch-davinci/emif_defs.h +++ b/include/asm-arm/arch-davinci/emif_defs.h @@ -55,6 +55,16 @@ typedef struct { dv_reg NANDF2ECC; dv_reg NANDF3ECC; dv_reg NANDF4ECC; + u_int8_t RSVD2[60]; + dv_reg NAND4BITECCLOAD; + dv_reg NAND4BITECC1; + dv_reg NAND4BITECC2; + dv_reg NAND4BITECC3; + dv_reg NAND4BITECC4; + dv_reg NANDERRADD1; + dv_reg NANDERRADD2; + dv_reg NANDERRVAL1; + dv_reg NANDERRVAL2; } emif_registers; typedef emif_registers *emifregs; diff --git a/include/asm-m68k/io.h b/include/asm-m68k/io.h index 50ea08751f..531f420336 100644 --- a/include/asm-m68k/io.h +++ b/include/asm-m68k/io.h @@ -28,6 +28,10 @@ #include <asm/byteorder.h> +#ifndef _IO_BASE +#define _IO_BASE 0 +#endif + #define __raw_readb(addr) (*(volatile u8 *)(addr)) #define __raw_readw(addr) (*(volatile u16 *)(addr)) #define __raw_readl(addr) (*(volatile u32 *)(addr)) diff --git a/include/asm-ppc/config.h b/include/asm-ppc/config.h index c9ba805077..5670d06a44 100644 --- a/include/asm-ppc/config.h +++ b/include/asm-ppc/config.h @@ -38,4 +38,11 @@ #endif #endif +#if defined(CONFIG_MPC8572) || defined(CONFIG_P1020) || \ + defined(CONFIG_P2020) || defined(CONFIG_MPC8641) +#define CONFIG_MAX_CPUS 2 +#else +#define CONFIG_MAX_CPUS 1 +#endif + #endif /* _ASM_CONFIG_H_ */ diff --git a/include/asm-ppc/fsl_pci.h b/include/asm-ppc/fsl_pci.h index 624ca5685a..f625d19ee4 100644 --- a/include/asm-ppc/fsl_pci.h +++ b/include/asm-ppc/fsl_pci.h @@ -20,8 +20,7 @@ #ifndef __FSL_PCI_H_ #define __FSL_PCI_H_ -int fsl_pci_setup_inbound_windows(struct pci_region *r); -void fsl_pci_init(struct pci_controller *hose); +void fsl_pci_init(struct pci_controller *hose, u32 cfg_addr, u32 cfg_data); void fsl_pci_config_unlock(struct pci_controller *hose); void ft_fsl_pci_setup(void *blob, const char *pci_alias, struct pci_controller *hose); @@ -155,4 +154,30 @@ typedef struct ccsr_pci { char res24[252]; } ccsr_fsl_pci_t; +struct fsl_pci_info { + unsigned long regs; + pci_addr_t mem_bus; + phys_size_t mem_phys; + pci_size_t mem_size; + pci_addr_t io_bus; + phys_size_t io_phys; + pci_size_t io_size; + int pci_num; +}; + +int fsl_pci_init_port(struct fsl_pci_info *pci_info, + struct pci_controller *hose, int busno); + +#define SET_STD_PCIE_INFO(x, num) \ +{ \ + x.regs = CONFIG_SYS_PCIE##num##_ADDR; \ + x.mem_bus = CONFIG_SYS_PCIE##num##_MEM_BUS; \ + x.mem_phys = CONFIG_SYS_PCIE##num##_MEM_PHYS; \ + x.mem_size = CONFIG_SYS_PCIE##num##_MEM_SIZE; \ + x.io_bus = CONFIG_SYS_PCIE##num##_IO_BUS; \ + x.io_phys = CONFIG_SYS_PCIE##num##_IO_PHYS; \ + x.io_size = CONFIG_SYS_PCIE##num##_IO_SIZE; \ + x.pci_num = num; \ +} + #endif diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 244c161580..db4b1eaa1e 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -86,11 +86,12 @@ typedef struct global_data { u32 mem_sec_clk; #endif /* CONFIG_MPC8360 */ #endif -#if defined(CONFIG_MPC837x) || defined(CONFIG_MPC8536) +#if defined(CONFIG_FSL_ESDHC) u32 sdhc_clk; #endif #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) u32 lbc_clk; + void *cpu; #endif /* CONFIG_MPC85xx || CONFIG_MPC86xx */ #if defined(CONFIG_MPC83xx) || defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) u32 i2c1_clk; diff --git a/include/asm-ppc/immap_85xx.h b/include/asm-ppc/immap_85xx.h index 0efef05214..375d80444f 100644 --- a/include/asm-ppc/immap_85xx.h +++ b/include/asm-ppc/immap_85xx.h @@ -411,6 +411,11 @@ typedef struct ccsr_l2cache { char res15[420]; } ccsr_l2cache_t; +#define MPC85xx_L2CTL_L2E 0x80000000 +#define MPC85xx_L2CTL_L2SRAM_ENTIRE 0x00010000 +#define MPC85xx_L2ERRDIS_MBECC 0x00000008 +#define MPC85xx_L2ERRDIS_SBECC 0x00000004 + /* * DMA Registers(0x2_1000-0x2_2000) */ diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 2841104515..dcaf8c030a 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -1009,6 +1009,12 @@ #define SVR_8569_E 0x808800 #define SVR_8572 0x80E000 #define SVR_8572_E 0x80E800 +#define SVR_P1011 0x80E500 +#define SVR_P1011_E 0x80ED00 +#define SVR_P1020 0x80E400 +#define SVR_P1020_E 0x80EC00 +#define SVR_P2010 0x80E300 +#define SVR_P2010_E 0x80EB00 #define SVR_P2020 0x80E200 #define SVR_P2020_E 0x80EA00 @@ -1065,13 +1071,14 @@ n: struct cpu_type { char name[15]; u32 soc_ver; + u32 num_cores; }; struct cpu_type *identify_cpu(u32 ver); #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) -#define CPU_TYPE_ENTRY(n, v) \ - { .name = #n, .soc_ver = SVR_##v, } +#define CPU_TYPE_ENTRY(n, v, nc) \ + { .name = #n, .soc_ver = SVR_##v, .num_cores = (nc), } #else #if defined(CONFIG_MPC83xx) #define CPU_TYPE_ENTRY(x) {#x, SPR_##x} diff --git a/include/bcd.h b/include/bcd.h index c545308125..af4aa9c7ba 100644 --- a/include/bcd.h +++ b/include/bcd.h @@ -3,18 +3,23 @@ * at your option. */ -/* macros to translate to/from binary and binary-coded decimal (frequently - * found in RTC chips). +/* inline functions to translate to/from binary and binary-coded decimal + * (frequently found in RTC chips). */ #ifndef _BCD_H #define _BCD_H -#define BCD2BIN(val) (((val) & 0x0f) + ((val)>>4)*10) -#define BIN2BCD(val) ((((val)/10)<<4) + (val)%10) +#include <linux/types.h> -/* backwards compat */ -#define BCD_TO_BIN(val) ((val)=BCD2BIN(val)) -#define BIN_TO_BCD(val) ((val)=BIN2BCD(val)) +static inline unsigned int bcd2bin(u8 val) +{ + return ((val) & 0x0f) + ((val) >> 4) * 10; +} + +static inline u8 bin2bcd (unsigned int val) +{ + return (((val / 10) << 4) | (val % 10)); +} #endif /* _BCD_H */ diff --git a/include/common.h b/include/common.h index a6922fd781..35f12c0b03 100644 --- a/include/common.h +++ b/include/common.h @@ -441,6 +441,8 @@ void ppcDWstore(unsigned int *addr, unsigned int *value); #endif /* $(CPU)/cpu.c */ +int cpu_numcores (void); +int probecpu (void); int checkcpu (void); int checkicache (void); int checkdcache (void); diff --git a/include/configs/ADNPESC1.h b/include/configs/ADNPESC1.h index b8afc172c5..2d4fc77915 100644 --- a/include/configs/ADNPESC1.h +++ b/include/configs/ADNPESC1.h @@ -426,15 +426,17 @@ /********************************************/ /* !!! CS8900 is __not__ tested on NIOS !!! */ /********************************************/ -#define CONFIG_DRIVER_CS8900 /* Using CS8900 */ -#define CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* Using CS8900 */ +#define CONFIG_CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + \ + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) #if (CONFIG_SYS_NIOS_CPU_LAN0_BUSW == 32) -#undef CS8900_BUS16 -#define CS8900_BUS32 1 +#undef CONFIG_CS8900_BUS16 +#define CONFIG_CS8900_BUS32 #else /* no */ -#define CS8900_BUS16 1 -#undef CS8900_BUS32 +#define CONFIG_CS8900_BUS16 +#undef CONFIG_CS8900_BUS32 #endif #else diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h index 7ee05e5658..91369a71e1 100644 --- a/include/configs/ATUM8548.h +++ b/include/configs/ATUM8548.h @@ -67,7 +67,6 @@ */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ /* * Only possible on E500 Version 2 or newer cores. diff --git a/include/configs/DK1C20.h b/include/configs/DK1C20.h index 45ff2f7dbc..cdc488b38e 100644 --- a/include/configs/DK1C20.h +++ b/include/configs/DK1C20.h @@ -232,15 +232,17 @@ /********************************************/ /* !!! CS8900 is __not__ tested on NIOS !!! */ /********************************************/ -#define CONFIG_DRIVER_CS8900 /* Using CS8900 */ -#define CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* Using CS8900 */ +#define CONFIG_CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + \ + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) #if (CONFIG_SYS_NIOS_CPU_LAN0_BUSW == 32) -#undef CS8900_BUS16 -#define CS8900_BUS32 1 +#undef CONFIG_CS8900_BUS16 +#define CONFIG_CS8900_BUS32 #else /* no */ -#define CS8900_BUS16 1 -#undef CS8900_BUS32 +#define CONFIG_CS8900_BUS16 +#undef CONFIG_CS8900_BUS32 #endif #else diff --git a/include/configs/DK1S10.h b/include/configs/DK1S10.h index ae567a32b3..6e788610fd 100644 --- a/include/configs/DK1S10.h +++ b/include/configs/DK1S10.h @@ -249,15 +249,17 @@ /********************************************/ /* !!! CS8900 is __not__ tested on NIOS !!! */ /********************************************/ -#define CONFIG_DRIVER_CS8900 /* Using CS8900 */ -#define CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* Using CS8900 */ +#define CONFIG_CS8900_BASE (CONFIG_SYS_NIOS_CPU_LAN0_BASE + \ + CONFIG_SYS_NIOS_CPU_LAN0_OFFS) #if (CONFIG_SYS_NIOS_CPU_LAN0_BUSW == 32) -#undef CS8900_BUS16 -#define CS8900_BUS32 1 +#undef CONFIG_CS8900_BUS16 +#define CONFIG_CS8900_BUS32 #else /* no */ -#define CS8900_BUS16 1 -#undef CS8900_BUS32 +#define CONFIG_CS8900_BUS16 +#undef CONFIG_CS8900_BUS32 #endif #else diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h index e7db0cc108..1801d9d7d5 100644 --- a/include/configs/M52277EVB.h +++ b/include/configs/M52277EVB.h @@ -255,7 +255,6 @@ # define CONFIG_ENV_IS_IN_FLASH 1 #endif #define CONFIG_ENV_OVERWRITE 1 -#undef CONFIG_ENV_IS_EMBEDDED /*----------------------------------------------------------------------- * FLASH organization diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h index 6b26c0bbc2..2b816ceae2 100644 --- a/include/configs/M5235EVB.h +++ b/include/configs/M5235EVB.h @@ -222,7 +222,6 @@ * Environment is embedded in u-boot in the second sector of the flash */ #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 #ifdef NORFLASH_PS32BIT # define CONFIG_ENV_OFFSET (0x8000) # define CONFIG_ENV_SIZE 0x4000 diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h index fc73d64091..f824158a69 100644 --- a/include/configs/M5272C3.h +++ b/include/configs/M5272C3.h @@ -55,7 +55,6 @@ #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 #else #define CONFIG_ENV_ADDR 0xffe04000 #define CONFIG_ENV_SECT_SIZE 0x2000 diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h index 210bb2deff..b380159812 100644 --- a/include/configs/M5275EVB.h +++ b/include/configs/M5275EVB.h @@ -55,7 +55,6 @@ #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 #else #define CONFIG_ENV_ADDR 0xffe04000 #define CONFIG_ENV_SECT_SIZE 0x2000 diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index a2d17c361c..8180c05e67 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -231,7 +231,6 @@ #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 /*----------------------------------------------------------------------- * Cache Configuration diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h index 98d800f310..8652a80aa1 100644 --- a/include/configs/M5373EVB.h +++ b/include/configs/M5373EVB.h @@ -231,7 +231,6 @@ #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 /*----------------------------------------------------------------------- * Cache Configuration diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h index fa444c39ee..a5acfd2846 100644 --- a/include/configs/M54451EVB.h +++ b/include/configs/M54451EVB.h @@ -277,7 +277,6 @@ # define CONFIG_ENV_SECT_SIZE 0x8000 #endif #undef CONFIG_ENV_OVERWRITE -#undef CONFIG_ENV_IS_EMBEDDED /* FLASH organization */ #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 14d98d69c8..7737284aab 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -332,7 +332,6 @@ # define CONFIG_ENV_IS_IN_FLASH 1 #endif #undef CONFIG_ENV_OVERWRITE -#undef CONFIG_ENV_IS_EMBEDDED /*----------------------------------------------------------------------- * FLASH organization diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h index e48de15f79..4534002e47 100644 --- a/include/configs/M5475EVB.h +++ b/include/configs/M5475EVB.h @@ -280,7 +280,6 @@ #define CONFIG_ENV_OFFSET 0x2000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 /*----------------------------------------------------------------------- * Cache Configuration diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h index 28bf0adcf3..971cb67bad 100644 --- a/include/configs/M5485EVB.h +++ b/include/configs/M5485EVB.h @@ -266,7 +266,6 @@ #define CONFIG_ENV_OFFSET 0x2000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 /*----------------------------------------------------------------------- * Cache Configuration diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 9d2b8600c2..4746e2ead5 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -27,6 +27,10 @@ #ifndef __CONFIG_H #define __CONFIG_H +#ifdef CONFIG_MPC8536DS_36BIT +#define CONFIG_PHYS_64BIT 1 +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ @@ -77,8 +81,13 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_ENABLE_36BIT_PHYS 1 -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x7fffffff +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00010000 /* skip exception vectors */ +#define CONFIG_SYS_MEMTEST_END 0x1f000000 /* skip u-boot at top of RAM */ #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* @@ -87,7 +96,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */ +#else #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#endif #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) @@ -96,6 +109,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0xb000) /* DDR Setup */ +#define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ @@ -170,7 +184,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Local Bus Definitions */ #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull +#else #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 @@ -178,7 +196,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) #define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE + 0x8000000, CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ @@ -199,7 +217,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ +#ifdef CONFIG_PHYS_64BIT +#define PIXIS_BASE_PHYS 0xfffdf0000ull +#else #define PIXIS_BASE_PHYS PIXIS_BASE +#endif #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ @@ -254,8 +276,12 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ -#define CONFIG_SYS_NAND_BASE 0xffa00000 -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ CONFIG_SYS_NAND_BASE + 0x40000, \ CONFIG_SYS_NAND_BASE + 0x80000, \ @@ -368,42 +394,78 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); */ #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCI1_MEM_BUS 0xf0000000 +#define CONFIG_SYS_PCI1_MEM_PHYS 0xc00000000ull +#else #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 +#endif #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xffc00000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCI1_IO_PHYS 0xfffc00000ull +#else +#define CONFIG_SYS_PCI1_IO_PHYS 0xffc00000 +#endif +#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 1, tgtid 1, Base address a000 */ #define CONFIG_SYS_PCIE1_MEM_VIRT 0x90000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0xf8000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc10000000ull +#else #define CONFIG_SYS_PCIE1_MEM_BUS 0x90000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x90000000 +#endif #define CONFIG_SYS_PCIE1_MEM_SIZE 0x08000000 /* 128M */ #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc10000ull +#else #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc10000 +#endif #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ /* controller 2, Slot 2, tgtid 2, Base address 9000 */ #define CONFIG_SYS_PCIE2_MEM_VIRT 0x98000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xf8000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc18000000ull +#else #define CONFIG_SYS_PCIE2_MEM_BUS 0x98000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0x98000000 +#endif #define CONFIG_SYS_PCIE2_MEM_SIZE 0x08000000 /* 128M */ #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc20000ull +#else #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000 +#endif #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 3, direct to uli, tgtid 3, Base address 8000 */ #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#else #define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000 +#endif #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc30000 -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc30000ull +#else #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc30000 +#endif #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ #if defined(CONFIG_PCI) diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index bebb9e9611..e69ba901ed 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -69,7 +69,6 @@ extern unsigned long get_clock_freq(void); */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ /* * Only possible on E500 Version 2 or newer cores. diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index d0933bae9d..55c1f29b19 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -34,7 +34,6 @@ #define CONFIG_MPC8572 1 #define CONFIG_MPC8572DS 1 #define CONFIG_MP 1 /* support multiple processors */ -#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index a3b5c7c3d3..761932800e 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -17,7 +17,6 @@ #define CONFIG_MPC86xx 1 /* MPC86xx */ #define CONFIG_MPC8610 1 /* MPC8610 specific */ #define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */ -#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ @@ -81,6 +80,7 @@ #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index bf2e359fd4..b0ae25c224 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -37,7 +37,6 @@ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ #define CONFIG_MP 1 /* support multiple processors */ -#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ /*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ #define CONFIG_ADDR_MAP 1 /* Use addr map */ diff --git a/include/configs/OXC.h b/include/configs/OXC.h index 104c23f928..74c51f46b2 100644 --- a/include/configs/OXC.h +++ b/include/configs/OXC.h @@ -196,7 +196,6 @@ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR 0xFFF30000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x00010000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* short-cut compile-time test */ #define CONFIG_ENV_OVERWRITE 1 /* Allow modifying the environment */ /* diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h new file mode 100644 index 0000000000..6d44d6c8dd --- /dev/null +++ b/include/configs/P1_P2_RDB.h @@ -0,0 +1,561 @@ +/* + * Copyright 2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * P1 P2 RDB board configuration file + * This file is intended to address a set of Low End and Ultra Low End + * Freescale SOCs of QorIQ series(RDB platforms). + * Currently only P2020RDB + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/P1020/P2020,etc*/ +#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */ +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1_P2 RDB */ +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for P1_P2 RDB */ + +#if defined(CONFIG_P2020) || defined(CONFIG_P1020) +#define CONFIG_MP +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of */ + /* CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ + /* CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) + +/* DDR Setup */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_DLL + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR size on P1_P2 RDBs */ +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00FF0000 + +#define CONFIG_SYS_DDR_TLB_START 9 + +/* + * Memory map + * + * 0x0000_0000 0x3fff_ffff DDR 1G cacheablen + * 0xa000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable + * 0xffc2_0000 0xffc5_ffff PCI IO range 256K non-cacheable + * + * Localbus cacheable (TBD) + * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable + * + * Localbus non-cacheable + * 0xef00_0000 0xefff_ffff FLASH 16M non-cacheable + * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable + * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xef000000 /* start of FLASH 16M */ + +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + BR_PS_16 | BR_V) +#define CONFIG_FLASH_OR_PRELIM 0xff000ff7 + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 + +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ + - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ + +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) + +/* NAND flash config */ +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ + +#define CONFIG_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ + +#define CONFIG_SYS_VSC7385_BASE 0xffb00000 + +#define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE + +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ + OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \ + OR_GPCM_EHTR | OR_GPCM_EAD) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +//#define CONFIG_CONS_INDEX 2 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* new uImage format support */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 2, Slot 2, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 1, Slot 1, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +#if defined(CONFIG_PCI) +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP +#undef CONFIG_RTL8139 + +#ifdef CONFIG_RTL8139 +/* This macro is used by RTL8139 but not defined in PPC architecture */ +#define KSEG1ADDR(x) (x) +#define _IO_BASE 0x00000000 +#endif + + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define CONFIG_VSC7385_ENET + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +/* Vitesse 7385 */ + +#ifdef CONFIG_VSC7385_ENET +/* The size of the VSC7385 firmware image */ +#define CONFIG_VSC7385_IMAGE_SIZE 8192 +#endif + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_MMC 1 + +#ifdef CONFIG_MMC +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_CMD_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_FSL_ESDHC +#define CONFIG_GENERIC_MMC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#ifdef CONFIG_P2020 +#define CONFIG_SYS_FSL_ESDHC_USE_PIO /* P2020 eSDHC DMA is not functional*/ +#endif +#endif + +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20)/* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#endif + +#define CONFIG_HOSTNAME P2020RDB +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "loadaddr=1000000\0" \ + "bootfile=uImage\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=rootfs.ext2.gz.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p2020rdb.dtb\0" \ + "bdev=sda1\0" \ + "jffs2nor=mtdblock3\0" \ + "norbootaddr=ef080000\0" \ + "norfdtaddr=ef040000\0" \ + "jffs2nand=mtdblock9\0" \ + "nandbootaddr=100000\0" \ + "nandfdtaddr=80000\0" \ + "nandimgsize=400000\0" \ + "nandfdtsize=80000\0" \ + "usb_phy_type=ulpi\0" \ + "vscfw_addr=ef000000\0" \ + "othbootargs=ramdisk_size=600000\0" \ + "usbfatboot=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "usb start;" \ + "fatload usb 0:2 $loadaddr $bootfile;" \ + "fatload usb 0:2 $fdtaddr $fdtfile;" \ + "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + "usbext2boot=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "usb start;" \ + "ext2load usb 0:4 $loadaddr $bootfile;" \ + "ext2load usb 0:4 $fdtaddr $fdtfile;" \ + "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + "norboot=setenv bootargs root=/dev/$jffs2nor rw " \ + "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ + "bootm $norbootaddr - $norfdtaddr\0" \ + "nandboot=setenv bootargs root=/dev/$jffs2nand rw rootfstype=jffs2 " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "nand read 2000000 $nandbootaddr $nandimgsize;" \ + "nand read 3000000 $nandfdtaddr $nandfdtsize;" \ + "bootm 2000000 - 3000000;\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "usb start;" \ + "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ + "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT + +#endif /* __CONFIG_H */ diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index ad24e0c884..46af7b9b06 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -34,7 +34,6 @@ #define CONFIG_P2020 1 #define CONFIG_P2020DS 1 #define CONFIG_MP 1 /* support multiple processors */ -#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index 6051480254..618b7f0a7e 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -108,9 +108,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20000300 +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ #define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */ diff --git a/include/configs/XPEDITE5170.h b/include/configs/XPEDITE5170.h index 8be9fa0555..242466ae12 100644 --- a/include/configs/XPEDITE5170.h +++ b/include/configs/XPEDITE5170.h @@ -34,7 +34,6 @@ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */ #define CONFIG_SYS_BOARD_NAME "XPedite5170" -#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h index acb62ad1dd..3c58ebe39b 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/XPEDITE5370.h @@ -36,7 +36,6 @@ #define CONFIG_MPC8572 1 #define CONFIG_XPEDITE5370 1 #define CONFIG_SYS_BOARD_NAME "XPedite5370" -#define CONFIG_NUM_CPUS 2 /* 2 Cores */ #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ diff --git a/include/configs/armadillo.h b/include/configs/armadillo.h index f7eec27685..49ea3a1668 100644 --- a/include/configs/armadillo.h +++ b/include/configs/armadillo.h @@ -56,10 +56,11 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20000300 /* armadillo board */ -#define CS8900_BUS16 1 -#undef CS8900_BUS32 +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20000300 /* armadillo board */ +#define CONFIG_CS8900_BUS16 +#undef CONFIG_CS8900_BUS32 /* * select serial console configuration diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index fb32f3f3c0..1c3ea23c77 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -127,7 +127,6 @@ #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_IS_EMBEDDED 1 #else #define CONFIG_ENV_ADDR 0xffe04000 #define CONFIG_ENV_SECT_SIZE 0x2000 diff --git a/include/configs/csb226.h b/include/configs/csb226.h index 12bab4702a..0661d65aba 100644 --- a/include/configs/csb226.h +++ b/include/configs/csb226.h @@ -150,9 +150,10 @@ /* * Network chip */ -#define CONFIG_DRIVER_CS8900 1 -#define CS8900_BUS32 1 -#define CS8900_BASE 0x08000000 +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 +#define CONFIG_CS8900_BUS32 +#define CONFIG_CS8900_BASE 0x08000000 /* * Stack sizes diff --git a/include/configs/ep7312.h b/include/configs/ep7312.h index 630fff3903..e151faa965 100644 --- a/include/configs/ep7312.h +++ b/include/configs/ep7312.h @@ -47,10 +47,11 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20000000 -#define CS8900_BUS16 1 -#undef CS8900_BUS32 +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20000000 +#define CONFIG_CS8900_BUS16 +#undef CONFIG_CS8900_BUS32 /* * select serial console configuration diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h new file mode 100644 index 0000000000..8d530d86aa --- /dev/null +++ b/include/configs/galaxy5200.h @@ -0,0 +1,428 @@ +/* + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2006 + * Eric Schumann, Phytec Messatechnik GmbH + * + * (C) Copyright 2009 + * Jon Smirl <jonsmirl@gmail.com> + * + * (C) Copyright 2009 + * Eric Millbrandt, DEKA Research and Development Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_BOARDINFO "galaxy5200" + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */ + /* define gps port conf. */ + /* register later on to */ + /* enable UART function! */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_PING +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_USB +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_FAT + +#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ + +#if (TEXT_BASE == 0xFE000000) /* Boot low */ +#define CONFIG_SYS_LOWBOOT 1 +#endif +/* RAMBOOT will be defined automatically in memory section */ + +#define MTDIDS_DEFAULT "nor0=physmap-flash.0" +#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \ + "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */ + /* even with bootdelay=0 */ +#undef CONFIG_BOOTARGS + +#define CONFIG_PREBOOT "echo;" \ + "echo Welcome to U-Boot;"\ + "echo" + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#define CONFIG_SYS_XLB_PIPELINING 1 + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM CAT24WC32 configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ +#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_SIZE 4096 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS3231 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * Flash configuration + */ + +#define CONFIG_SYS_FLASH_BASE 0xfe000000 +/* + * The flash size is autoconfigured, but cpu/mpc5xxx/cpu_init.c needs this + * variable defined + */ +#define CONFIG_SYS_FLASH_SIZE 0x02000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ + /* (= chip selects) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* + * Use hardware protection. This seems required, as the BDI uses hardware + * protection. Without this, U-Boot can't work with this sectors as its + * protection is software only by default. + */ +#define CONFIG_SYS_FLASH_PROTECTION 1 + +/* + * Environment settings + */ + +#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ + /* beginning of the EEPROM */ +#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE + +#define CONFIG_ENV_OVERWRITE 1 + +/* + * SDRAM configuration + */ +#define SDRAM_DDR 1 +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x71500F00 +#define SDRAM_CONFIG1 0x73711930 +#define SDRAM_CONFIG2 0x47770000 + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */ + /* bootloader or debugger config */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM + +/* End of used area in SPRAM */ +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE + +/* Size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* Chip Select configuration for NAND flash */ +#define CONFIG_SYS_CS1_START 0x20000000 +#define CONFIG_SYS_CS1_SIZE 0x90000 +#define CONFIG_SYS_CS1_CFG 0x0002d900 + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x01 +#define CONFIG_NO_AUTOLOAD 1 + +/* + * GPIO configuration + * + * GPS port configuration + * + * [29:31] = 01x + * AC97 on PSC1 + * PSC1_0 -> AC97 SDATA out + * PSC1_1 -> AC97 SDTA in + * PSC1_2 -> AC97 SYNC out + * PSC1_3 -> AC97 bitclock out + * PSC1_4 -> AC97 reset out + * + * [28] = Reserved + * + * [25:27] = 110 + * SPI on PSC2 + * PSC2_0 -> MOSI + * PSC2_1 -> MISO + * PSC2_2 -> n/a + * PSC2_3 -> CLK + * PSC2_4 -> SS + * + * [24] = Reserved + * + * [20:23] = 0001 + * USB on PSC3 + * PSC3_0 -> USB_OE OE out + * PSC3_1 -> USB_TXN Tx- out + * PSC3_2 -> USB_TXP Tx+ out + * PSC3_3 -> USB_TXD + * PSC3_4 -> USB_RXP Rx+ in + * PSC3_5 -> USB_RXN Rx- in + * PSC3_6 -> USB_PWR PortPower out + * PSC3_7 -> USB_SPEED speed out + * PSC3_8 -> USB_SUSPEND suspend + * PSC3_9 -> USB_OVRCURNT overcurrent in + * + * [18:19] = 10 + * Two UARTs + * + * [17] = 0 + * USB differential mode + * + * [16] = 1 + * PCI disabled + * + * [12:15] = 0101 + * Ethernet 100Mbit with MD + * ETH_0 -> ETH Txen + * ETH_1 -> ETH TxD0 + * ETH_2 -> ETH TxD1 + * ETH_3 -> ETH TxD2 + * ETH_4 -> ETH TxD3 + * ETH_5 -> ETH Txerr + * ETH_6 -> ETH MDC + * ETH_7 -> ETH MDIO + * ETH_8 -> ETH RxDv + * ETH_9 -> ETH RxCLK + * ETH_10 -> ETH Collision + * ETH_11 -> ETH TxD + * ETH_12 -> ETH RxD0 + * ETH_13 -> ETH RxD1 + * ETH_14 -> ETH RxD2 + * ETH_15 -> ETH RxD3 + * ETH_16 -> ETH Rxerr + * ETH_17 -> ETH CRS + * + * [9:11] = 111 + * SPI on PSC6 + * PSC6_0 -> MISO + * PSC6_1 -> SS# + * PSC6_2 -> MOSI + * PSC6_3 -> CLK + * + * [8] = 0 + * IrDA/USB 48MHz clock generated internally + * + * [6:7] = 01 + * ATA chip selects on csb_4/5 + * CSB_4 -> ATA_CS0 out + * CSB_5 -> ATA_CS1 out + * + * [5] = 1 + * PSC3_4 is used as CS6 + * + * [4] = 1 + * PSC3_5 is used as CS7 + * + * [2:3] = 00 + * No Alternatives + * + * [1] = 0 + * gpio_wkup_7 is GPIO + * + * [0] = 0 + * gpio_wkup_6 is GPIO + * + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_DISPLAY_BOARDINFO 1 + +#define CONFIG_SYS_HUSH_PARSER 1 +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_CRC32_VERIFY 1 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_DNS | \ + CONFIG_BOOTP_DNS2 | \ + CONFIG_BOOTP_SEND_HOSTNAME ) + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +/* no burst access on the LPB */ +#define CONFIG_SYS_CS_BURST 0x00000000 +/* one deadcycle for the 33MHz statemachine */ +#define CONFIG_SYS_CS_DEADCYCLE 0x33333331 + +#define CONFIG_SYS_BOOTCS_CFG 0x0002d900 +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE + +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 + +/* + * USB settings + */ +#define CONFIG_USB_CLOCK 0x0001bbbb +/* USB is on PSC3 */ +#define CONFIG_PSC3_USB +#define CONFIG_USB_CONFIG 0x00000100 +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* + * IDE/ATA stuff Supports IDE harddisk + */ +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ +#define CONFIG_IDE_PREINIT +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 +#define CONFIG_ATAPI 1 + +/* we enable IDE and FAT support, so we also need partition support */ +#define CONFIG_DOS_PARTITION 1 + +/* + * Open Firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN +#define OF_SOC "soc5200@f0000000" +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600" + +#endif /* __CONFIG_H */ diff --git a/include/configs/impa7.h b/include/configs/impa7.h index c7001cc7de..fdfa022c0b 100644 --- a/include/configs/impa7.h +++ b/include/configs/impa7.h @@ -47,9 +47,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20000000 -#define CS8900_BUS32 1 +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20000000 +#define CONFIG_CS8900_BUS32 /* * select serial console configuration diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index 869fd4ca1a..79d8638fe2 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -324,6 +324,12 @@ #define CONFIG_SYS_DTT_HYSTERESIS 3 #define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) +#if defined(CONFIG_CMD_NAND) +#define CONFIG_NAND_KMETER1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE CONFIG_SYS_PIGGY_BASE +#endif + #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif diff --git a/include/configs/lart.h b/include/configs/lart.h index 5d6d460424..2d3b369aae 100644 --- a/include/configs/lart.h +++ b/include/configs/lart.h @@ -47,9 +47,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x20008300 -#define CS8900_BUS16 1 +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x20008300 +#define CONFIG_CS8900_BUS16 /* * select serial console configuration diff --git a/include/configs/mx1ads.h b/include/configs/mx1ads.h index 12e567bf7d..b2ffd3e935 100644 --- a/include/configs/mx1ads.h +++ b/include/configs/mx1ads.h @@ -66,9 +66,10 @@ /* * CS8900 Ethernet drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x15000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x15000300 +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ /* * select serial console configuration diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 363ea1ba1f..ec1c905403 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -109,9 +109,10 @@ "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \ "setenv filesize; saveenv\0" -#define CONFIG_DRIVER_CS8900 1 -#define CS8900_BASE 0xb4020300 -#define CS8900_BUS16 1 /* follow the Linux driver */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 +#define CONFIG_CS8900_BASE 0xb4020300 +#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */ /* * The MX31ADS board seems to have a hardware "peculiarity" confirmed under diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h index 8a83d924bb..027e8e16b3 100644 --- a/include/configs/nhk8815.h +++ b/include/configs/nhk8815.h @@ -138,6 +138,10 @@ #define CONFIG_SMC_USE_32_BIT #define CONFIG_BOOTFILE "uImage" +#define CONFIG_IP_DEFRAG /* Allows faster download, TFTP and NFS */ +#define CONFIG_TFTP_BLOCKSIZE 4096 +#define CONFIG_NFS_READ_SIZE 4096 + /* Storage information: onenand and nand */ #define CONFIG_CMD_ONENAND #define CONFIG_MTD_ONENAND_VERIFY_WRITE diff --git a/include/configs/pcu_e.h b/include/configs/pcu_e.h index 7c2bf1b0f4..6517381170 100644 --- a/include/configs/pcu_e.h +++ b/include/configs/pcu_e.h @@ -231,7 +231,6 @@ #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment */ #define CONFIG_ENV_ADDR 0xFFFFE000 /* Address of Environment Sector */ #define CONFIG_ENV_SECT_SIZE 0x2000 /* use the top-most 8k boot sector */ -#define CONFIG_ENV_IS_EMBEDDED 1 /* short-cut compile-time test */ #else /* Final version: environment in EEPROM */ #define CONFIG_ENV_IS_IN_EEPROM 1 diff --git a/include/configs/sbc2410x.h b/include/configs/sbc2410x.h index f3dc7fe979..f2ea926f92 100644 --- a/include/configs/sbc2410x.h +++ b/include/configs/sbc2410x.h @@ -63,9 +63,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x19000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x19000300 +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ /* * select serial console configuration diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index a2ff9557ce..838b4db9ad 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -59,7 +59,6 @@ */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ /* * Only possible on E500 Version 2 or newer cores. diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index ef0f627b6c..2865df55e9 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -41,7 +41,6 @@ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_SBC8641D 1 /* SBC8641D board specific */ #define CONFIG_MP 1 /* support multiple processors */ -#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #ifdef RUN_DIAG @@ -107,6 +106,7 @@ #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) #define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) diff --git a/include/configs/smdk2400.h b/include/configs/smdk2400.h index b712db44f4..c234177767 100644 --- a/include/configs/smdk2400.h +++ b/include/configs/smdk2400.h @@ -56,9 +56,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x07000300 /* agrees with WIN CE PA */ -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x07000300 /* agrees with WIN CE PA */ +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ /* * select serial console configuration diff --git a/include/configs/smdk2410.h b/include/configs/smdk2410.h index a4732783d9..d340098d0b 100644 --- a/include/configs/smdk2410.h +++ b/include/configs/smdk2410.h @@ -53,9 +53,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x19000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x19000300 +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ /* * select serial console configuration diff --git a/include/configs/smdk6400.h b/include/configs/smdk6400.h index ddc8e7174a..f6e1221294 100644 --- a/include/configs/smdk6400.h +++ b/include/configs/smdk6400.h @@ -74,9 +74,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x18800300 -#define CS8900_BUS16 1 /* follow the Linux driver */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x18800300 +#define CONFIG_CS8900_BUS16 /* follow the Linux driver */ /* * select serial console configuration diff --git a/include/configs/trab.h b/include/configs/trab.h index 7687ee6dcb..43c191b435 100644 --- a/include/configs/trab.h +++ b/include/configs/trab.h @@ -99,9 +99,10 @@ /* * Hardware drivers */ -#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ -#define CS8900_BASE 0x07000300 /* agrees with WIN CE PA */ -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CONFIG_NET_MULTI +#define CONFIG_CS8900 /* we have a CS8900 on-board */ +#define CONFIG_CS8900_BASE 0x07000300 /* agrees with WIN CE PA */ +#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */ #define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */ diff --git a/include/e500.h b/include/e500.h index 84b580de1f..f8c82661a2 100644 --- a/include/e500.h +++ b/include/e500.h @@ -8,13 +8,9 @@ #ifndef __ASSEMBLY__ -#ifndef CONFIG_NUM_CPUS -#define CONFIG_NUM_CPUS 1 -#endif - typedef struct { - unsigned long freqProcessor[CONFIG_NUM_CPUS]; + unsigned long freqProcessor[CONFIG_MAX_CPUS]; unsigned long freqSystemBus; unsigned long freqDDRBus; unsigned long freqLocalBus; diff --git a/include/environment.h b/include/environment.h index 5bed32fd47..b9924fd778 100644 --- a/include/environment.h +++ b/include/environment.h @@ -67,6 +67,10 @@ # if defined(CONFIG_ENV_ADDR_REDUND) || defined(CONFIG_ENV_OFFSET_REDUND) # define CONFIG_SYS_REDUNDAND_ENVIRONMENT 1 # endif +# ifdef CONFIG_ENV_IS_EMBEDDED +# error "do not define CONFIG_ENV_IS_EMBEDDED in your board config" +# error "it is calculated automatically for you" +# endif #endif /* CONFIG_ENV_IS_IN_FLASH */ #if defined(CONFIG_ENV_IS_IN_NAND) @@ -79,9 +83,6 @@ # ifdef CONFIG_ENV_OFFSET_REDUND # define CONFIG_SYS_REDUNDAND_ENVIRONMENT # endif -# ifdef CONFIG_ENV_IS_EMBEDDED -# define ENV_IS_EMBEDDED 1 -# endif #endif /* CONFIG_ENV_IS_IN_NAND */ #if defined(CONFIG_ENV_IS_IN_MG_DISK) @@ -91,11 +92,32 @@ # ifndef CONFIG_ENV_SIZE # error "Need to define CONFIG_ENV_SIZE when using CONFIG_ENV_IS_IN_MG_DISK" # endif -# ifdef CONFIG_ENV_IS_EMBEDDED -# error "CONFIG_ENV_IS_EMBEDDED not supported when using CONFIG_ENV_IS_IN_MG_DISK" -# endif #endif /* CONFIG_ENV_IS_IN_MG_DISK */ +/* Embedded env is only supported for some flash types */ +#ifdef CONFIG_ENV_IS_EMBEDDED +# if !defined(CONFIG_ENV_IS_IN_FLASH) && \ + !defined(CONFIG_ENV_IS_IN_NAND) && \ + !defined(CONFIG_ENV_IS_IN_ONENAND) +# error "CONFIG_ENV_IS_EMBEDDED not supported for your flash type" +# endif +#endif + +/* + * For the flash types where embedded env is supported, but it cannot be + * calculated automatically (i.e. NAND), take the board opt-in. + */ +#if defined(CONFIG_ENV_IS_EMBEDDED) && !defined(ENV_IS_EMBEDDED) +# define ENV_IS_EMBEDDED 1 +#endif + +/* The build system likes to know if the env is embedded */ +#ifdef DO_DEPS_ONLY +# ifdef ENV_IS_EMBEDDED +# define CONFIG_ENV_IS_EMBEDDED +# endif +#endif + #include "compiler.h" #ifdef CONFIG_SYS_REDUNDAND_ENVIRONMENT diff --git a/include/flash.h b/include/flash.h index b016162009..8feca1b5fa 100644 --- a/include/flash.h +++ b/include/flash.h @@ -46,7 +46,7 @@ typedef struct { ushort cmd_reset; /* vendor specific reset command */ ushort interface; /* used for x8/x16 adjustments */ ushort legacy_unlock; /* support Intel legacy (un)locking */ - uchar manufacturer_id; /* manufacturer id */ + ushort manufacturer_id; /* manufacturer id */ ushort device_id; /* device id */ ushort device_id2; /* extended device id */ ushort ext_addr; /* extended query table address */ @@ -154,6 +154,7 @@ extern flash_info_t *flash_get_info(ulong base); * Device IDs */ +/* Manufacturers inside bank 0 have ids like 0x00xx00xx */ #define AMD_MANUFACT 0x00010001 /* AMD manuf. ID in D23..D16, D7..D0 */ #define FUJ_MANUFACT 0x00040004 /* FUJITSU manuf. ID in D23..D16, D7..D0 */ #define ATM_MANUFACT 0x001F001F /* ATMEL */ @@ -166,6 +167,13 @@ extern flash_info_t *flash_get_info(ulong base); #define TOSH_MANUFACT 0x00980098 /* TOSHIBA manuf. ID in D23..D16, D7..D0 */ #define MT2_MANUFACT 0x002C002C /* alternate MICRON manufacturer ID*/ #define EXCEL_MANUFACT 0x004A004A /* Excel Semiconductor */ +#define AMIC_MANUFACT 0x00370037 /* AMIC manuf. ID in D23..D16, D7..D0 */ +#define WINB_MANUFACT 0x00DA00DA /* Winbond manuf. ID in D23..D16, D7..D0 */ + +/* Manufacturers inside bank 1 have ids like 0x01xx01xx */ +#define EON_MANUFACT 0x011C011C /* EON manuf. ID in D23..D16, D7..D0 */ + +/* Manufacturers inside bank 2 have ids like 0x02xx02xx */ /* Micron Technologies (INTEL compat.) */ #define MT_ID_28F400_T 0x44704470 /* 28F400B3 ID ( 4 M, top boot sector) */ diff --git a/include/linux/mc146818rtc.h b/include/linux/mc146818rtc.h index 227feeb0cd..0644d92b3c 100644 --- a/include/linux/mc146818rtc.h +++ b/include/linux/mc146818rtc.h @@ -83,16 +83,4 @@ #define RTC_VALID RTC_REG_D # define RTC_VRT 0x80 /* valid RAM and time */ /**********************************************************************/ - -/* example: !(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY) - * determines if the following two #defines are needed - */ -#ifndef BCD_TO_BIN -#define BCD_TO_BIN(val) ((val)=((val)&15) + ((val)>>4)*10) -#endif - -#ifndef BIN_TO_BCD -#define BIN_TO_BCD(val) ((val)=(((val)/10)<<4) + (val)%10) -#endif - #endif /* _MC146818RTC_H */ diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 3e0044b94f..cb7c19a439 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -128,6 +128,7 @@ typedef enum { NAND_ECC_SOFT, NAND_ECC_HW, NAND_ECC_HW_SYNDROME, + NAND_ECC_HW_OOB_FIRST, } nand_ecc_modes_t; /* @@ -268,13 +269,13 @@ struct nand_ecc_ctrl { uint8_t *calc_ecc); int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, - uint8_t *buf); + uint8_t *buf, int page); void (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf); int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, - uint8_t *buf); + uint8_t *buf, int page); int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip, uint32_t offs, uint32_t len, diff --git a/include/linux/mtd/onenand.h b/include/linux/mtd/onenand.h index 2597e347b4..06f7bafeae 100644 --- a/include/linux/mtd/onenand.h +++ b/include/linux/mtd/onenand.h @@ -83,10 +83,9 @@ struct onenand_chip { size_t len); int (*wait) (struct mtd_info *mtd, int state); int (*bbt_wait) (struct mtd_info *mtd, int state); + void (*unlock_all)(struct mtd_info *mtd); int (*read_bufferram) (struct mtd_info *mtd, loff_t addr, int area, unsigned char *buffer, int offset, size_t count); - int (*read_spareram) (struct mtd_info *mtd, loff_t addr, int area, - unsigned char *buffer, int offset, size_t count); int (*write_bufferram) (struct mtd_info *mtd, loff_t addr, int area, const unsigned char *buffer, int offset, size_t count); diff --git a/include/netdev.h b/include/netdev.h index 50329a3f53..a50ec67d53 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -43,6 +43,7 @@ int cpu_eth_init(bd_t *bis); /* Driver initialization prototypes */ int au1x00_enet_initialize(bd_t*); int bfin_EMAC_initialize(bd_t *bis); +int cs8900_initialize(u8 dev_num, int base_addr); int dc21x4x_initialize(bd_t *bis); int davinci_emac_initialize(void); int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr); diff --git a/include/pci.h b/include/pci.h index aaa4554344..491f814e41 100644 --- a/include/pci.h +++ b/include/pci.h @@ -222,6 +222,7 @@ #define PCI_CAP_ID_SLOTID 0x04 /* Slot Identification */ #define PCI_CAP_ID_MSI 0x05 /* Message Signalled Interrupts */ #define PCI_CAP_ID_CHSWP 0x06 /* CompactPCI HotSwap */ +#define PCI_CAP_ID_EXP 0x10 /* PCI Express */ #define PCI_CAP_LIST_NEXT 1 /* Next capability in the list */ #define PCI_CAP_FLAGS 2 /* Capability defined flags (16 bits) */ #define PCI_CAP_SIZEOF 4 diff --git a/include/rtc.h b/include/rtc.h index 785fbe3807..772a548841 100644 --- a/include/rtc.h +++ b/include/rtc.h @@ -27,6 +27,11 @@ #ifndef _RTC_H_ #define _RTC_H_ +/* bcd<->bin functions are needed by almost all the RTC drivers, let's include + * it there instead of in evey single driver */ + +#include <bcd.h> + /* * The struct used to pass data from the generic interface code to * the hardware dependend low-level code ande vice versa. Identical |