diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/HWW1U1A.h | 460 |
1 files changed, 0 insertions, 460 deletions
diff --git a/include/configs/HWW1U1A.h b/include/configs/HWW1U1A.h deleted file mode 100644 index 6a3a11cb7f..0000000000 --- a/include/configs/HWW1U1A.h +++ /dev/null @@ -1,460 +0,0 @@ -/* - * Copyright 2009-2010 eXMeritus, A Boeing Company - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * HardwareWall HWW-1U-1A airborne unit configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High-level system configuration options */ -#define CONFIG_BOOKE /* Power/PowerPC Book-E */ -#define CONFIG_E500 /* e500 (Power ISA v2.03 with SPE) */ -#define CONFIG_FSL_ELBC /* FreeScale Enhanced LocalBus Cntlr */ -#define CONFIG_FSL_LAW /* FreeScale Local Access Window */ -#define CONFIG_P2020 /* FreeScale P2020 */ -#define CONFIG_HWW1U1A /* eXMeritus HardwareWall HWW-1U-1A */ -#define CONFIG_MP /* Multiprocessing support */ -#define CONFIG_HWCONFIG /* Use hwconfig from environment */ - -#define CONFIG_L2_CACHE /* L2 cache enabled */ -#define CONFIG_BTB /* Branch predition enabled */ - -#define CONFIG_PANIC_HANG /* No board reset on panic */ -#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r() */ -#define CONFIG_CMD_REGINFO /* Dump various CPU regs */ - -/* - * Allow the use of 36-bit physical addresses. Device-trees with 64-bit - * addresses have known compatibility issues with some existing kernels. - */ -#define CONFIG_ENABLE_36BIT_PHYS -#define CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP -#define CONFIG_SYS_NUM_ADDR_MAP 16 /* Number of entries in TLB1 */ - -/* Reserve plenty of RAM for malloc (we have 2GB+) */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) - -/* How much L2 cache do we map so we can use it as RAM */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -/* This is our temporary global data area just above the stack */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* The stack grows down from the global data area */ -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Enable IRQs and watchdog with a 1000Hz system decrementer */ -#define CONFIG_CMD_IRQ - -/* -------------------------------------------------------------------- */ - -/* - * Clock crystal configuration: - * (1) SYS: 66.666MHz +/- 50ppm (drives CPU/PCI/DDR) - * (2) CCB: Multiplier from SYS_CLK - * (3) RTC: 25.000MHz +/- 50ppm (sampled against CCB clock) - */ -#define CONFIG_SYS_CLK_FREQ 66666000/*Hz*/ -#define CONFIG_DDR_CLK_FREQ 66666000/*Hz*/ - - -/* -------------------------------------------------------------------- */ - -/* - * Memory map - * - * 0x0000_0000 0x7fff_ffff 2G DDR2 ECC SDRAM - * 0x8000_0000 0x9fff_ffff 512M PCI-E Bus 1 - * 0xa000_0000 0xbfff_ffff 512M PCI-E Bus 2 (unused) - * 0xc000_0000 0xdfff_ffff 512M PCI-E Bus 3 - * 0xe000_0000 0xe7ff_ffff 128M Spansion FLASH - * 0xe800_0000 0xefff_ffff 128M Spansion FLASH - * 0xffd0_0000 0xffd0_3fff 16K L1 boot stack (TLB0) - * 0xffe0_0000 0xffef_ffff 1M CCSR - * 0xffe0_5000 0xffe0_5fff 4K Enhanced LocalBus Controller - */ - -/* Virtual Memory Map */ -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 -#define CONFIG_SYS_FLASH_BASE 0xe0000000 -#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* CCSRBAR @ runtime */ - -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -/* Physical Memory Map */ -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull -#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull -#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull -#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull -#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfffd00000ull -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf /* for ASM code */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xffd00000 /* for ASM code */ -#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf /* for ASM code */ -#define CONFIG_SYS_CCSRBAR_PHYS_LOW 0xffe00000 /* for ASM code */ - - -/* -------------------------------------------------------------------- */ - -/* U-Boot image (MONITOR_BASE == TEXT_BASE) */ -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc /* Top address in flash */ -#define CONFIG_SYS_TEXT_BASE 0xeff80000 /* Start of U-Boot image */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN 0x80000 /* 512kB (4 flash sectors) */ - -/* - * U-Boot Environment Image: The two sectors immediately below U-Boot - * form the U-Boot environment (regular and redundant). - */ -#define CONFIG_ENV_IS_IN_FLASH /* The environment image is stored in FLASH */ -#define CONFIG_ENV_OVERWRITE /* Allow "protected" variables to be erased */ -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128kB (1 flash sector) */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) - -/* Only use 8kB of each environment sector for data */ -#define CONFIG_ENV_SIZE 0x2000 /* 8kB */ -#define CONFIG_ENV_SIZE_REDUND 0x2000 /* 8kB */ - - -/* -------------------------------------------------------------------- */ - -/* Serial Console Configuration */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Echo back characters received during a serial download */ -#define CONFIG_LOADS_ECHO - -/* Allow a serial-download to temporarily change baud */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE - - -/* -------------------------------------------------------------------- */ - -/* PCI and PCI-Express Support */ -#define CONFIG_PCI /* Enable PCI/PCIE */ -#define CONFIG_PCI_PNP /* Scan PCI busses */ -#define CONFIG_CMD_PCI /* Enable the "pci" command */ -#define CONFIG_FSL_PCI_INIT /* Common FreeScale PCI initialization */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_FSL_PCIE_RESET /* We have PCI-E reset errata */ -#define CONFIG_SYS_PCI_64BIT /* PCI resources are 64-bit */ -#define CONFIG_PCI_SCAN_SHOW /* Display PCI scan during boot */ - -/* Enable 2 of the 3 PCI-E controllers */ -#define CONFIG_PCIE3 -#undef CONFIG_PCIE2 -#define CONFIG_PCIE1 - -/* Display human-readable names when initializing */ -#define CONFIG_SYS_PCIE3_NAME "Intel 82571EB" -#define CONFIG_SYS_PCIE2_NAME "Unused" -#define CONFIG_SYS_PCIE1_NAME "Silicon Image SIL3531" - -/* - * PCI bus addresses - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 - - -/* -------------------------------------------------------------------- */ - -/* Generic FreeScale hardware I2C support */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } -#define CONFIG_CMD_I2C - -/* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */ -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS 0x51 - -/* DS1339 RTC is at I2C0-0x68 (I know it says "DS1337", it's a DS1339) */ -#define CONFIG_CMD_DATE -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_RTC_BUS_NUM 0 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -/* Turn off RTC square-wave output to save battery */ -#define CONFIG_SYS_RTC_DS1337_NOOSC - -/* - * AT24C128N EEPROM at I2C0-0x53. - * - * That Atmel EEPROM has 128kbit of memory (16kByte) divided into 256 pages - * of 64 bytes per page. The chip uses 2-byte addresses and has a max write - * cycle time of 20ms according to the datasheet. - * - * NOTE: Our environment is stored on regular direct-attached FLASH, this - * chip is only used as a write-protected backup for certain key settings - * such as the serial# and macaddr values. (EG: "env import") - */ -#define CONFIG_CMD_EEPROM -#define CONFIG_ENV_EEPROM_IS_ON_I2C -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 1 << 6 == 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 21 - -/* - * PCA9554 is at I2C1-0x3f (I know it says "PCA953X", it's a PCA9554). You - * must first select the I2C1 bus with "i2c dev 1" or the "pca953x" command - * will not be able to access the chip. - */ -#define CONFIG_PCA953X -#define CONFIG_CMD_PCA953X -#define CONFIG_CMD_PCA953X_INFO -#define CONFIG_SYS_I2C_PCA953X_ADDR 0x3f - - -/* -------------------------------------------------------------------- */ - -/* FreeScale DDR2/3 SDRAM Controller */ -#define CONFIG_SYS_FSL_DDR2 /* Our SDRAM slot is DDR2 */ -#define CONFIG_DDR_ECC /* Enable ECC by default */ -#define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */ -#define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */ -#define CONFIG_VERY_BIG_RAM /* Allow 2GB+ of RAM */ -#define CONFIG_CMD_SDRAM - -/* Standard P2020 DDR controller parameters */ -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* Make sure to tell the DDR controller to preinitialze all of RAM */ -#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER - - -/* -------------------------------------------------------------------- */ - -/* FLASH Memory Configuration (2x 128MB SPANSION FLASH) */ -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 - -/* Flash banks (2x 128MB) */ -#define FLASH0_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000ull) -#define FLASH1_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x0000000ull) -#define CONFIG_SYS_MAX_FLASH_BANKS 2 -#define CONFIG_SYS_MAX_FLASH_SECT 1024 -#define CONFIG_SYS_FLASH_BANKS_LIST { FLASH0_PHYS, FLASH1_PHYS } - -/* - * Flash access modes and timings (values are the defaults after a RESET). - * - * NOTE: These could probably be optimized but are more than sufficient for - * this particular system for the moment. - */ -#define FLASH_BRx (BR_PS_16 | BR_MS_GPCM | BR_V) -#define FLASH_ORx (OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) - -/* Configure both flash banks */ -#define CONFIG_SYS_BR0_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH0_PHYS)) -#define CONFIG_SYS_BR1_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH1_PHYS)) -#define CONFIG_SYS_OR0_PRELIM (FLASH_ORx | OR_AM_128MB) -#define CONFIG_SYS_OR1_PRELIM (FLASH_ORx | OR_AM_128MB) - -/* Flash timeouts (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000UL /* Erase (60s) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500UL /* Write (0.5s) */ - -/* Quiet flash testing */ -#define CONFIG_SYS_FLASH_QUIET_TEST - -/* Make program/erase count down from 45/5 (9....8....7....) */ -#define CONFIG_FLASH_SHOW_PROGRESS 45 - - -/* -------------------------------------------------------------------- */ - -/* Ethernet Device Support */ -#define CONFIG_MII /* Enable MII PHY code */ -#define CONFIG_MII_DEFAULT_TSEC /* ??? Copied from P2020DS */ -#define CONFIG_PHY_GIGE /* Support Gigabit PHYs */ -#define CONFIG_ETHPRIME "e1000#0" /* Default to external ports */ - -/* Turn on various helpful networking commands */ -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING - -/* On-chip FreeScale P2020 "tsec" Ethernet (oneway fibers and peer) */ -#define CONFIG_TSEC_ENET -#define CONFIG_TSEC1 -#define CONFIG_TSEC2 -#define CONFIG_TSEC3 -#define CONFIG_TSEC1_NAME "owt0" -#define CONFIG_TSEC2_NAME "owt1" -#define CONFIG_TSEC3_NAME "peer" -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 3 -#define TSEC3_PHY_ADDR 4 -#define TSEC3_PHY_ADDR_CPUA 4 -#define TSEC3_PHY_ADDR_CPUB 5 - -/* PCI-E dual-port E1000 (external ethernet ports) */ -#define CONFIG_E1000 -#define CONFIG_E1000_SPI -#define CONFIG_E1000_SPI_GENERIC -#define CONFIG_CMD_E1000 - -/* We need the SPI infrastructure to poke the E1000's EEPROM */ -#define CONFIG_SPI -#define CONFIG_SPI_X -#define CONFIG_CMD_SPI -#define MAX_SPI_BYTES 32 - - -/* -------------------------------------------------------------------- */ - -/* USB Thumbdrive Device Support */ -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_FSL -#define CONFIG_USB_STORAGE -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_CMD_USB - -/* Partition and Filesystem support */ -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT - - -/* -------------------------------------------------------------------- */ - -/* Command line configuration. */ -#define CONFIG_CMDLINE_EDITING /* Enable command editing */ -#define CONFIG_COMMAND_HISTORY /* Enable command history */ -#define CONFIG_AUTO_COMPLETE /* Enable command completion */ -#define CONFIG_SYS_LONGHELP /* Enable detailed command help */ -#define CONFIG_SYS_MAXARGS 128 /* Up to 128 command-line args */ -#define CONFIG_SYS_PBSIZE 8192 /* Allow up to 8k printed lines */ -#define CONFIG_SYS_CBSIZE 4096 /* Allow up to 4k command lines */ -#define CONFIG_SYS_BARGSIZE 4096 /* Allow up to 4k boot args */ -#define CONFIG_SYS_HUSH_PARSER /* Enable a fancier shell */ - -/* A little extra magic here for the prompt */ -#define CONFIG_SYS_PROMPT hww1u1a_get_ps1() -#ifndef __ASSEMBLY__ -const char *hww1u1a_get_ps1(void); -#endif - -/* Include a bunch of default commands we probably want */ -#include <config_cmd_default.h> - -/* Other helpful shell-like commands */ -#define CONFIG_MD5 -#define CONFIG_SHA1 -#define CONFIG_CMD_MD5SUM -#define CONFIG_CMD_SHA1SUM -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_SETEXPR - - -/* -------------------------------------------------------------------- */ - -/* Image manipulation and booting */ - -/* We use the OpenFirmware-esque "Flattened Device Tree" */ -#define CONFIG_OF_LIBFDT -#define CONFIG_OF_BOARD_SETUP -#define CONFIG_OF_STDOUT_VIA_ALIAS - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMD_ELF -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Maximum kernel memory map */ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Maximum kernel size of 64MB */ - -/* This is the default address for commands with an optional address arg */ -#define CONFIG_LOADADDR 100000 -#define CONFIG_SYS_LOAD_ADDR 0x100000 - -/* Test memory starting from the default load address to just below 2GB */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_LOAD_ADDR -#define CONFIG_SYS_MEMTEST_END 0x7f000000 - -#define CONFIG_BOOTDELAY 20 -#define CONFIG_BOOTCOMMAND "echo Not yet flashed" -#define CONFIG_BOOTARGS "" -#define CONFIG_BOOTARGS_DYNAMIC "console=ttyS0,${baudrate}n1" - -/* Extra environment parameters */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ethprime=e1000#0\0" \ - "ethrotate=no\0" \ - "setbootargs=setenv bootargs " \ - "\"${bootargs} "CONFIG_BOOTARGS_DYNAMIC"\"\0" \ - "perf_mode=performance\0" \ - "hwconfig=" "fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \ - "usb1:dr_mode=host,phy_type=ulpi\0" \ - "flkernel=0xe8000000\0" \ - "flinitramfs=0xe8800000\0" \ - "fldevicetree=0xeff20000\0" \ - "flbootm=bootm ${flkernel} ${flinitramfs} ${fldevicetree}\0" \ - "flboot=run preboot; run flbootm\0" \ - "restore_eeprom=i2c dev 0 && " \ - "eeprom read $loadaddr 0x0000 0x2000 && " \ - "env import -c $loadaddr 0x2000\0" - -#endif /* __CONFIG_H */ |