diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-ppc/i2c.h | 2 | ||||
| -rw-r--r-- | include/asm-ppc/immap_83xx.h | 30 | ||||
| -rw-r--r-- | include/configs/TQM834x.h | 522 | ||||
| -rw-r--r-- | include/mpc83xx.h | 91 |
4 files changed, 609 insertions, 36 deletions
diff --git a/include/asm-ppc/i2c.h b/include/asm-ppc/i2c.h index 2a4ac0ff36..fa9d164e9a 100644 --- a/include/asm-ppc/i2c.h +++ b/include/asm-ppc/i2c.h @@ -87,7 +87,7 @@ typedef struct i2c #error CFG_I2C_OFFSET is not defined in /include/configs/${BOARD}.h #endif -#ifdef CONFIG_MPC8349ADS +#if defined(CONFIG_MPC8349ADS) || defined(CONFIG_TQM834X) /* * MPC8349 have two i2c bus */ diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 5d284d4679..f704db63ff 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -613,9 +613,9 @@ typedef struct gpio8349 { typedef struct ddr_cs_bnds{ u32 csbnds; #define CSBNDS_SA 0x00FF0000 -#define CSBNDS_SA_SHIFT 16 +#define CSBNDS_SA_SHIFT 8 #define CSBNDS_EA 0x000000FF -#define CSBNDS_EA_SHIFT 0 +#define CSBNDS_EA_SHIFT 24 u8 res0[4]; } ddr_cs_bnds_t; @@ -652,6 +652,8 @@ typedef struct ddr8349{ #define TIMING_CFG1_ACTTOACT_SHIFT 4 #define TIMING_CFG1_WRTORD 0x00000007 #define TIMING_CFG1_WRTORD_SHIFT 0 +#define TIMING_CFG1_CASLAT_20 0x00030000 /* CAS latency = 2.0 */ +#define TIMING_CFG1_CASLAT_25 0x00040000 /* CAS latency = 2.5 */ u32 timing_cfg_2; /**< SDRAM Timing Configuration 2 */ #define TIMING_CFG2_CPO 0x0F000000 @@ -659,6 +661,7 @@ typedef struct ddr8349{ #define TIMING_CFG2_ACSM 0x00080000 #define TIMING_CFG2_WR_DATA_DELAY 0x00001C00 #define TIMING_CFG2_WR_DATA_DELAY_SHIFT 10 +#define TIMING_CFG2_CPO_DEF 0x00000000 /* default (= CASLAT + 1) */ u32 sdram_cfg; /**< SDRAM Control Configuration */ #define SDRAM_CFG_MEM_EN 0x80000000 @@ -672,6 +675,7 @@ typedef struct ddr8349{ #define SDRAM_CFG_8_BE 0x00040000 #define SDRAM_CFG_NCAP 0x00020000 #define SDRAM_CFG_2T_EN 0x00008000 +#define SDRAM_CFG_SDRAM_TYPE_DDR 0x02000000 u8 res2[4]; u32 sdram_mode; /**< SDRAM Mode Configuration */ @@ -679,6 +683,25 @@ typedef struct ddr8349{ #define SDRAM_MODE_ESD_SHIFT 16 #define SDRAM_MODE_SD 0x0000FFFF #define SDRAM_MODE_SD_SHIFT 0 +#define DDR_MODE_EXT_MODEREG 0x4000 /* select extended mode reg */ +#define DDR_MODE_EXT_OPMODE 0x3FF8 /* operating mode, mask */ +#define DDR_MODE_EXT_OP_NORMAL 0x0000 /* normal operation */ +#define DDR_MODE_QFC 0x0004 /* QFC / compatibility, mask */ +#define DDR_MODE_QFC_COMP 0x0000 /* compatible to older SDRAMs */ +#define DDR_MODE_WEAK 0x0002 /* weak drivers */ +#define DDR_MODE_DLL_DIS 0x0001 /* disable DLL */ +#define DDR_MODE_CASLAT 0x0070 /* CAS latency, mask */ +#define DDR_MODE_CASLAT_15 0x0010 /* CAS latency 1.5 */ +#define DDR_MODE_CASLAT_20 0x0020 /* CAS latency 2 */ +#define DDR_MODE_CASLAT_25 0x0060 /* CAS latency 2.5 */ +#define DDR_MODE_CASLAT_30 0x0030 /* CAS latency 3 */ +#define DDR_MODE_BTYPE_SEQ 0x0000 /* sequential burst */ +#define DDR_MODE_BTYPE_ILVD 0x0008 /* interleaved burst */ +#define DDR_MODE_BLEN_2 0x0001 /* burst length 2 */ +#define DDR_MODE_BLEN_4 0x0002 /* burst length 4 */ +#define DDR_REFINT_166MHZ_7US 1302 /* exact value for 7.8125 µs */ +#define DDR_BSTOPRE 256 /* use 256 cycles as a starting point */ +#define DDR_MODE_MODEREG 0x0000 /* select mode register */ u8 res3[8]; u32 sdram_interval; /**< SDRAM Interval Configuration */ @@ -688,6 +711,9 @@ typedef struct ddr8349{ #define SDRAM_INTERVAL_BSTOPRE_SHIFT 0 u8 res9[8]; u32 sdram_clk_cntl; +#define DDR_SDRAM_CLK_CNTL_SS_EN 0x80000000 +#define DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 0x02000000 + u8 res4[0xCCC]; u32 data_err_inject_hi; /**< Memory Data Path Error Injection Mask High */ u32 data_err_inject_lo; /**< Memory Data Path Error Injection Mask Low */ diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h new file mode 100644 index 0000000000..96a1ad28fc --- /dev/null +++ b/include/configs/TQM834x.h @@ -0,0 +1,522 @@ +/* + * (C) Copyright 2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * TQM8349 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define DEBUG +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC834X 1 /* MPC834X specific */ +#define CONFIG_TQM834X 1 /* TQM834X board specific */ + +/* IMMR Base Addres Register, use Freescale default: 0xff400000 */ +#define CFG_IMMRBAR 0xff400000 + +/* System clock. Primary input clock when in PCI host mode */ +#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */ + +/* + * Local Bus LCRR + * LCRR: DLL bypass, Clock divider is 8 + * + * for CSB = 266 MHz it gives LCB clock frequency = 33 MHz + * + * External Local Bus rate is + * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) + +/* board pre init: do not call, nothing to do */ +#undef CONFIG_BOARD_EARLY_INIT_F + +/* detect the number of flash banks */ +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define DDR_CASLAT_25 /* CASLAT set to 2.5 */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00000000 /* memtest region */ +#define CFG_MEMTEST_END 0x00100000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_BASE 0x80000000 /* start of FLASH */ + +/* buffered writes in the AMD chip set is not supported yet */ +#undef CFG_FLASH_USE_BUFFER_WRITE + +/* + * FLASH bank number detection + */ + +/* + * When CFG_MAX_FLASH_BANKS_DETECT is defined, the actual number of Flash + * banks has to be determined at runtime and stored in a gloabl variable + * tqm834x_num_flash_banks. The value of CFG_MAX_FLASH_BANKS_DETECT is only + * used insted of CFG_MAX_FLASH_BANKS to allocate the array flash_info, and + * should be made sufficiently large to accomodate the number of banks that + * might acutally be detected. Since most (all?) Flash related functions use + * CFG_MAX_FLASH_BANKS as the number of actual banks on the board, it is + * defined as tqm834x_num_flash_banks. + */ +#define CFG_MAX_FLASH_BANKS_DETECT 2 +#ifndef __ASSEMBLY__ +extern int tqm834x_num_flash_banks; +#endif +#define CFG_MAX_FLASH_BANKS (tqm834x_num_flash_banks) + +#define CFG_MAX_FLASH_SECT 512 /* max sectors per device */ + +/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA) | \ + BR_MS_GPCM | BR_PS_32 | BR_V) + +/* FLASH timing (0x0000_0c54) */ +#define CFG_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_0b10 | \ + OR_GPCM_SCY_5 | OR_GPCM_TRLX) + +#define CFG_PRELIM_OR_AM 0xc0000000 /* OR addr mask: 1 GiB */ + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) + +#define CFG_LBLAWAR0_PRELIM 0x8000001D /* 1 GiB window size (2^(size + 1)) */ +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ + +/* disable remaining mappings */ +#define CFG_BR1_PRELIM 0x00000000 +#define CFG_OR1_PRELIM 0x00000000 +#define CFG_LBLAWBAR1_PRELIM 0x00000000 +#define CFG_LBLAWAR1_PRELIM 0x00000000 + +#define CFG_BR2_PRELIM 0x00000000 +#define CFG_OR2_PRELIM 0x00000000 +#define CFG_LBLAWBAR2_PRELIM 0x00000000 +#define CFG_LBLAWAR2_PRELIM 0x00000000 + +#define CFG_BR3_PRELIM 0x00000000 +#define CFG_OR3_PRELIM 0x00000000 +#define CFG_LBLAWBAR3_PRELIM 0x00000000 +#define CFG_LBLAWAR3_PRELIM 0x00000000 + +#define CFG_BR4_PRELIM 0x00000000 +#define CFG_OR4_PRELIM 0x00000000 +#define CFG_LBLAWBAR4_PRELIM 0x00000000 +#define CFG_LBLAWAR4_PRELIM 0x00000000 + +#define CFG_BR5_PRELIM 0x00000000 +#define CFG_OR5_PRELIM 0x00000000 +#define CFG_LBLAWBAR5_PRELIM 0x00000000 +#define CFG_LBLAWAR5_PRELIM 0x00000000 + +#define CFG_BR6_PRELIM 0x00000000 +#define CFG_OR6_PRELIM 0x00000000 +#define CFG_LBLAWBAR6_PRELIM 0x00000000 +#define CFG_LBLAWAR6_PRELIM 0x00000000 + +#define CFG_BR7_PRELIM 0x00000000 +#define CFG_OR7_PRELIM 0x00000000 +#define CFG_LBLAWBAR7_PRELIM 0x00000000 +#define CFG_LBLAWAR7_PRELIM 0x00000000 + +/* + * Monitor config + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/ + +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_IMMRBAR + 0x4500) +#define CFG_NS16550_COM2 (CFG_IMMRBAR + 0x4600) + +/* + * I2C + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */ +#define CFG_I2C_SLAVE 0x7F /* slave address */ +#define CFG_I2C_OFFSET 0x3000 + +/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */ +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */ +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_MII + +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMRBAR + CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMRBAR + CFG_TSEC2_OFFSET) + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MPC83XX_TSEC1 1 +#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0" +#define CONFIG_MPC83XX_TSEC2 1 +#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +/* FIXME: Real PCI support will come in a follow-up update. */ +#undef CONFIG_PCI + +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe2000000 +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#define CFG_PCI2_MEM_BASE 0xA0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0x00000000 +#define CFG_PCI2_IO_PHYS 0xe3000000 +#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ +#if defined(CONFIG_PCI) + +#define PCI_ALL_PCI1 +#if defined(PCI_64BIT) +#undef PCI_ALL_PCI1 +#undef PCI_TWO_PCI1 +#undef PCI_ONE_PCI1 +#endif + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xFIXME + #define PCI_ENET0_MEMADDR 0xFIXME + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +/* + * Environment + */ +#define CONFIG_ENV_OVERWRITE + +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* Common commands */ +#define CFG_CMD_TQM8349_COMMON CFG_CMD_DATE | CFG_CMD_I2C | CFG_CMD_DTT\ + | CFG_CMD_PING | CFG_CMD_EEPROM \ + | CFG_CMD_MII | CFG_CMD_JFFS2 + +#if defined(CFG_RAMBOOT) + +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI \ + | CFG_CMD_TQM8349_COMMON) \ + & \ + ~(CFG_CMD_ENV | CFG_CMD_LOADS)) +#else +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_TQM8349_COMMON) \ + & \ + ~(CFG_CMD_ENV | CFG_CMD_LOADS)) +#endif + +#else /* CFG_RAMBOOT */ + +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI \ + | CFG_CMD_TQM8349_COMMON) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_TQM8349_COMMON) +#endif + +#endif /* CFG_RAMBOOT */ + +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_VCO_1X2 |\ + HRCWL_CORE_TO_CSB_2X1) + +#if defined(PCI_64BIT) +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_64_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII ) +#else +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_32_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII ) +#endif + +/* i-cache and d-cache disabled */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL CFG_HID0_INIT +#define CFG_HID2 0x000000000 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_ETHADDR D2:DA:5E:44:BC:29 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 1E:F3:40:21:92:53 +#endif + +#define CONFIG_IPADDR 192.168.205.1 + +#define CONFIG_HOSTNAME tqm8349 +#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx +#define CONFIG_BOOTFILE /tftpboot/tqm83xx/uImage + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=tqm83xx\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=/tftpboot/tqm83xx/uImage\0" \ + "kernel_addr=80060000\0" \ + "ramdisk_addr=80160000\0" \ + "load=tftp 100000 /tftpboot/tqm83xx/u-boot.bin\0" \ + "update=protect off 80000000 8003ffff; " \ + "era 80000000 8003ffff; cp.b 100000 80000000 40000\0" \ + "upd=run load;run update\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * JFFS2 partitions + */ +/* mtdparts command line support */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=TQM834x-0" + +/* default mtd partition table */ +#define MTDPARTS_DEFAULT "mtdparts=TQM834x-0:256k(u-boot),128k(env),"\ + "1m(kernel),2m(initrd),"\ + "-(user);"\ + +#endif /* __CONFIG_H */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 38f7115b18..ea40bad395 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -98,19 +98,27 @@ #define BR6 0x5030 #define BR7 0x5038 -#define BR_BA 0xFFFF8000 -#define BR_BA_SHIFT 15 -#define BR_PS 0x00001800 -#define BR_PS_SHIFT 11 -#define BR_DECC 0x00000600 -#define BR_DECC_SHIFT 9 -#define BR_WP 0x00000100 -#define BR_WP_SHIFT 8 -#define BR_MSEL 0x000000E0 -#define BR_MSEL_SHIFT 5 -#define BR_V 0x00000001 -#define BR_V_SHIFT 0 -#define BR_RES ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V) +#define BR_BA 0xFFFF8000 +#define BR_BA_SHIFT 15 +#define BR_PS 0x00001800 +#define BR_PS_SHIFT 11 +#define BR_PS_8 0x00000800 /* Port Size 8 bit */ +#define BR_PS_16 0x00001000 /* Port Size 16 bit */ +#define BR_PS_32 0x00001800 /* Port Size 32 bit */ +#define BR_DECC 0x00000600 +#define BR_DECC_SHIFT 9 +#define BR_WP 0x00000100 +#define BR_WP_SHIFT 8 +#define BR_MSEL 0x000000E0 +#define BR_MSEL_SHIFT 5 +#define BR_MS_GPCM 0x00000000 /* GPCM */ +#define BR_MS_SDRAM 0x00000060 /* SDRAM */ +#define BR_MS_UPMA 0x00000080 /* UPMA */ +#define BR_MS_UPMB 0x000000A0 /* UPMB */ +#define BR_MS_UPMC 0x000000C0 /* UPMC */ +#define BR_V 0x00000001 +#define BR_V_SHIFT 0 +#define BR_RES ~(BR_BA|BR_PS|BR_DECC|BR_WP|BR_MSEL|BR_V) #define OR0 0x5004 #define OR1 0x500C @@ -121,26 +129,43 @@ #define OR6 0x5034 #define OR7 0x503C -#define OR_GPCM_AM 0xFFFF8000 -#define OR_GPCM_AM_SHIFT 15 -#define OR_GPCM_BCTLD 0x00001000 -#define OR_GPCM_BCTLD_SHIFT 12 -#define OR_GPCM_CSNT 0x00000800 -#define OR_GPCM_CSNT_SHIFT 11 -#define OR_GPCM_ACS 0x00000600 -#define OR_GPCM_ACS_SHIFT 9 -#define OR_GPCM_XACS 0x00000100 -#define OR_GPCM_XACS_SHIFT 8 -#define OR_GPCM_SCY 0x000000F0 -#define OR_GPCM_SCY_SHIFT 4 -#define OR_GPCM_SETA 0x00000008 -#define OR_GPCM_SETA_SHIFT 3 -#define OR_GPCM_TRLX 0x00000004 -#define OR_GPCM_TRLX_SHIFT 2 -#define OR_GPCM_EHTR 0x00000002 -#define OR_GPCM_EHTR_SHIFT 1 -#define OR_GPCM_EAD 0x00000001 -#define OR_GPCM_EAD_SHIFT 0 +#define OR_GPCM_AM 0xFFFF8000 +#define OR_GPCM_AM_SHIFT 15 +#define OR_GPCM_BCTLD 0x00001000 +#define OR_GPCM_BCTLD_SHIFT 12 +#define OR_GPCM_CSNT 0x00000800 +#define OR_GPCM_CSNT_SHIFT 11 +#define OR_GPCM_ACS 0x00000600 +#define OR_GPCM_ACS_SHIFT 9 +#define OR_GPCM_ACS_0b10 0x00000400 +#define OR_GPCM_ACS_0b11 0x00000600 +#define OR_GPCM_XACS 0x00000100 +#define OR_GPCM_XACS_SHIFT 8 +#define OR_GPCM_SCY 0x000000F0 +#define OR_GPCM_SCY_SHIFT 4 +#define OR_GPCM_SCY_1 0x00000010 +#define OR_GPCM_SCY_2 0x00000020 +#define OR_GPCM_SCY_3 0x00000030 +#define OR_GPCM_SCY_4 0x00000040 +#define OR_GPCM_SCY_5 0x00000050 +#define OR_GPCM_SCY_6 0x00000060 +#define OR_GPCM_SCY_7 0x00000070 +#define OR_GPCM_SCY_8 0x00000080 +#define OR_GPCM_SCY_9 0x00000090 +#define OR_GPCM_SCY_10 0x000000a0 +#define OR_GPCM_SCY_11 0x000000b0 +#define OR_GPCM_SCY_12 0x000000c0 +#define OR_GPCM_SCY_13 0x000000d0 +#define OR_GPCM_SCY_14 0x000000e0 +#define OR_GPCM_SCY_15 0x000000f0 +#define OR_GPCM_SETA 0x00000008 +#define OR_GPCM_SETA_SHIFT 3 +#define OR_GPCM_TRLX 0x00000004 +#define OR_GPCM_TRLX_SHIFT 2 +#define OR_GPCM_EHTR 0x00000002 +#define OR_GPCM_EHTR_SHIFT 1 +#define OR_GPCM_EAD 0x00000001 +#define OR_GPCM_EAD_SHIFT 0 #define OR_UPM_AM 0xFFFF8000 #define OR_UPM_AM_SHIFT 15 |