diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/cm_t3517.h | 219 |
1 files changed, 0 insertions, 219 deletions
diff --git a/include/configs/cm_t3517.h b/include/configs/cm_t3517.h deleted file mode 100644 index c876853cd5..0000000000 --- a/include/configs/cm_t3517.h +++ /dev/null @@ -1,219 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2013 CompuLab, Ltd. - * Author: Igor Grinberg <grinberg@compulab.co.il> - * - * Configuration settings for the CompuLab CM-T3517 board - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_CM_T3517 /* working with CM-T3517 */ - -/* - * This is needed for the DMA stuff. - * Although the default iss 64, we still define it - * to be on the safe side once the default is changed. - */ - -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap.h> - -#define CONFIG_MACH_TYPE MACH_TYPE_CM_T3517 - -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -/* - * The early kernel mapping on ARM currently only maps from the base of DRAM - * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. - * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, - * so that leaves DRAM base to DRAM base + 0x4000 available. - */ -#define CONFIG_SYS_BOOTMAPSZ 0x4000 - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG -#define CONFIG_SERIAL_TAG - -/* - * Size of malloc() pool - */ -#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - -/* - * Hardware drivers - */ - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -/* - * select serial console configuration - */ -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* USB */ - -#ifndef CONFIG_USB_MUSB_AM35X -#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146 -#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147 -#endif /* CONFIG_USB_MUSB_AM35X */ - -/* commands to include */ - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_BUS 0 -#define CONFIG_I2C_MULTI_BUS - -/* - * Board NAND Info. - */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand at */ - /* CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ - -/* Environment information */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "loadaddr=0x82000000\0" \ - "baudrate=115200\0" \ - "console=ttyO2,115200n8\0" \ - "netretry=yes\0" \ - "mpurate=auto\0" \ - "vram=12M\0" \ - "dvimode=1024x768MR-16@60\0" \ - "defaultdisplay=dvi\0" \ - "mmcdev=0\0" \ - "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \ - "mmcrootfstype=ext4\0" \ - "nandroot=/dev/mtdblock4 rw\0" \ - "nandrootfstype=ubifs\0" \ - "mmcargs=setenv bootargs console=${console} " \ - "mpurate=${mpurate} " \ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${mmcroot} " \ - "rootfstype=${mmcrootfstype}\0" \ - "nandargs=setenv bootargs console=${console} " \ - "mpurate=${mpurate} " \ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${nandroot} " \ - "rootfstype=${nandrootfstype}\0" \ - "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source ${loadaddr}\0" \ - "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "bootm ${loadaddr}\0" \ - "nandboot=echo Booting from nand ...; " \ - "run nandargs; " \ - "nand read ${loadaddr} 2a0000 400000; " \ - "bootm ${loadaddr}\0" \ - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run nandboot; " \ - "fi; " \ - "fi; " \ - "else run nandboot; fi" - -/* - * Miscellaneous configurable options - */ -#define CONFIG_TIMESTAMP -#define CONFIG_SYS_AUTOLOAD "no" -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ - -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) - -/* - * AM3517 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -#define CONFIG_SYS_HZ 1000 - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define CONFIG_SYS_CS0_SIZE (256 << 20) - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -/* **** PISMO SUPPORT *** */ -/* Monitor at start of flash */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#define CONFIG_ENV_OFFSET 0x260000 -#define CONFIG_ENV_ADDR 0x260000 - -#if defined(CONFIG_CMD_NET) -#define CONFIG_DRIVER_TI_EMAC_USE_RMII -#define CONFIG_ARP_TIMEOUT 200UL -#define CONFIG_NET_RETRY_COUNT 5 -#endif /* CONFIG_CMD_NET */ - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* Status LED */ -#define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */ - -/* Display Configuration */ -#define LCD_BPP LCD_COLOR16 - -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SPLASHIMAGE_GUARD -#define CONFIG_BMP_16BPP -#define CONFIG_SCF0403_LCD - -/* EEPROM */ -#define CONFIG_ENV_EEPROM_IS_ON_I2C -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 -#define CONFIG_SYS_EEPROM_SIZE 256 - -#endif /* __CONFIG_H */ |