diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-ppc/processor.h | 13 | ||||
| -rw-r--r-- | include/configs/TQM5200.h | 34 | ||||
| -rw-r--r-- | include/configs/TQM8272.h | 754 | ||||
| -rw-r--r-- | include/configs/alpr.h | 19 | ||||
| -rw-r--r-- | include/configs/idmr.h | 197 | ||||
| -rw-r--r-- | include/configs/sequoia.h | 5 | ||||
| -rw-r--r-- | include/configs/spc1920.h | 102 | ||||
| -rw-r--r-- | include/configs/v38b.h | 7 | ||||
| -rw-r--r-- | include/configs/yellowstone.h | 14 | ||||
| -rw-r--r-- | include/configs/yosemite.h | 14 | ||||
| -rw-r--r-- | include/flash.h | 1 | ||||
| -rw-r--r-- | include/mpc8260.h | 10 | ||||
| -rw-r--r-- | include/ppc440.h | 20 |
13 files changed, 1144 insertions, 46 deletions
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 6619686876..f102600038 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -747,11 +747,14 @@ #define PVR_440GX_RC 0x51B21892 #define PVR_440GX_RF 0x51B21894 #define PVR_405EP_RB 0x51210950 -#define PVR_440SP_RA 0x53221850 -#define PVR_440SP_RB 0x53221891 -#define PVR_440SP_RC 0x53221892 -#define PVR_440SPe_RA 0x53421890 -#define PVR_440SPe_RB 0x53421891 +#define PVR_440SP_6_RAB 0x53221850 /* 440SP rev A&B with RAID 6 support enabled */ +#define PVR_440SP_RAB 0x53321850 /* 440SP rev A&B without RAID 6 support */ +#define PVR_440SP_6_RC 0x53221891 /* 440SP rev C with RAID 6 support enabled */ +#define PVR_440SP_RC 0x53321891 /* 440SP rev C without RAID 6 support */ +#define PVR_440SPe_6_RA 0x53421890 /* 440SPe rev A with RAID 6 support enabled */ +#define PVR_440SPe_RA 0x53521890 /* 440SPe rev A without RAID 6 support */ +#define PVR_440SPe_6_RB 0x53421891 /* 440SPe rev B with RAID 6 support enabled */ +#define PVR_440SPe_RB 0x53521891 /* 440SPe rev B without RAID 6 support */ #define PVR_601 0x00010000 #define PVR_602 0x00050000 #define PVR_603 0x00030000 diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 08674ca49f..7069b35ad6 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -231,6 +231,17 @@ "protect on FC000000 +${filesize}\0" #endif +#ifndef CONFIG_CAM5200 +#define CUSTOM_ENV_SETTINGS \ + "bootfile=/tftpboot/tqm5200/uImage\0" \ + "u-boot=/tftpboot/tqm5200/u-boot.bin\0" +#else +#define CUSTOM_ENV_SETTINGS \ + "bootfile=cam5200/uImage\0" \ + "u-boot=cam5200/u-boot.bin\0" \ + "setup=tftp 200000 cam5200/setup.img; autoscr 200000\0" +#endif + #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ @@ -248,8 +259,7 @@ "bootm ${kernel_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \ "bootm\0" \ - "bootfile=/tftpboot/tqm5200/uImage\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ + CUSTOM_ENV_SETTINGS \ "load=tftp 200000 ${u-boot}\0" \ ENV_UPDT \ "" @@ -325,15 +335,7 @@ */ #define CFG_FLASH_BASE 0xFC000000 -#ifndef CONFIG_CAM5200 -/* use CFI flash driver */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#else /* CONFIG_CAM5200 */ +#if defined(CONFIG_CAM5200) && defined(CONFIG_CAM5200_NIOSFLASH) #define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks (= chip selects) */ #define CFG_FLASH_WORD_SIZE unsigned int /* main flash device with */ @@ -344,7 +346,15 @@ #define CFG_FLASH_ADDR1 0x2AA #define CFG_FLASH_2ND_16BIT_DEV 1 /* NIOS flash is a 16bit device */ #define CFG_MAX_FLASH_SECT 128 -#endif /* ifndef CONFIG_CAM5200 */ +#else +/* use CFI flash driver */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#endif #define CFG_FLASH_EMPTY_INFO #define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h new file mode 100644 index 0000000000..925bf34317 --- /dev/null +++ b/include/configs/TQM8272.h @@ -0,0 +1,754 @@ +/* + * (C) Copyright 2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ +#define CONFIG_MPC8272_FAMILY 1 +#define CONFIG_TQM8272 1 + +#define CONFIG_GET_CPU_STR_F 1 /* Get the CPU ID STR */ +#define CONFIG_BOARD_GET_CPU_CLK_F 1 /* Get the CLKIN from board fct */ + +#define STK82xx_150 1 /* on a STK82xx.150 */ + +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_EARLY_INIT_R 1 + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 115200 +#endif + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consdev=ttyCPM0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "hostname=tqm8272\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} " \ + "console=$(consdev),$(baudrate)\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 300000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "bootfile=/tftpboot/tqm8272/uImage\0" \ + "kernel_addr=40080000\0" \ + "ramdisk_addr=40100000\0" \ + "load=tftp 300000 /tftpboot/tqm8272/u-boot.bin\0" \ + "update=protect off 40000000 4003ffff;era 40000000 4003ffff;" \ + "cp.b 300000 40000000 40000;" \ + "setenv filesize;saveenv\0" \ + "cphwib=cp.b 4003fc00 33fc00 400\0" \ + "upd=run load;run cphwib;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_I2C 1 + +#if CONFIG_I2C +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define ADD_CMD_I2C CFG_CMD_I2C | \ + CFG_CMD_DATE |\ + CFG_CMD_DTT |\ + CFG_CMD_EEPROM +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_I2C_X + +/* EEPROM */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE /* necessary for the LM75 chip */ +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#else +#undef CONFIG_HARD_I2C +#undef CONFIG_SOFT_I2C +#define ADD_CMD_I2C 0 +#endif + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#ifdef CONFIG_82xx_CONS_SMC1 +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#endif +#ifdef CONFIG_82xx_CONS_SMC2 +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ +#endif + +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + * + * (On TQM8272 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the + * X.29 connector, and FCC2 is hardwired to the X.1 connector) + */ +#define CFG_FCC_ETHERNET + +#if defined(CFG_FCC_ETHERNET) +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ +#else +#define CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ +#endif + +#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) + +/* + * - RX clk is CLK11 + * - TX clk is CLK12 + */ +# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +/* + * GPIO pins used for bit-banged MII communications + */ +#define MDIO_PORT 2 /* Port C */ + +#if STK82xx_150 +#define CFG_MDIO_PIN 0x00008000 /* PC16 */ +#define CFG_MDC_PIN 0x00004000 /* PC17 */ +#endif + +#if STK82xx_100 +#define CFG_MDIO_PIN 0x00000002 /* PC30 */ +#define CFG_MDC_PIN 0x00000001 /* PC31 */ +#endif + +#if 1 +#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN) +#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN) +#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \ + else iop->pdat &= ~CFG_MDIO_PIN + +#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \ + else iop->pdat &= ~CFG_MDC_PIN +#else +#define MDIO_ACTIVE ({unsigned long tmp; tmp = iop->pdir; tmp |= CFG_MDIO_PIN; iop->pdir = tmp;}) +#define MDIO_TRISTATE ({unsigned long tmp; tmp = iop->pdir; tmp &= ~CFG_MDIO_PIN; iop->pdir = tmp;}) +#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) + +#define MDIO(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDIO_PIN; iop->pdat = tmp;}\ + else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDIO_PIN; iop->pdat = tmp;} + +#define MDC(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDC_PIN; iop->pdat = tmp;}\ + else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDC_PIN; iop->pdat = tmp;} +#endif + +#define MIIDELAY udelay(1) + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_DHCP | \ + CFG_CMD_PING | \ + ADD_CMD_I2C | \ + CFG_CMD_NFS | \ + CFG_CMD_MII | \ + CFG_CMD_PCI | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if 0 +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x300000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0x40000104 /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * CAN stuff + *----------------------------------------------------------------------- + */ +#define CFG_CAN_BASE 0x51000000 +#define CFG_CAN_SIZE 1 +#define CFG_CAN_BR ((CFG_CAN_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMC |\ + BRx_V) + +#define CFG_CAN_OR (MEG_TO_AM(CFG_CAN_SIZE) |\ + ORxU_BI) + + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/tqm8272/config.mk + * The main FLASH is whichever is connected to *CS0. + */ +#define CFG_FLASH0_BASE 0x40000000 +#define CFG_FLASH0_SIZE 32 /* 32 MB */ + +/* Flash bank size (for preliminary settings) + */ +#define CFG_FLASH_SIZE CFG_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CFG_UPDATE_FLASH_SIZE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x40000) +#define CFG_ENV_SIZE 0x20000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND 0x20000 + +/* Where is the Hardwareinformation Block (from Monitor Sources) */ +#define MON_RES_LENGTH (0x0003FC00) +#define HWIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH) +#define HWIB_INFO_LEN 512 +#define CIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH + HWIB_INFO_LEN) +#define CIB_INFO_LEN 512 + +#define CFG_HWINFO_OFFSET 0x3fc00 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000060 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#define CFG_NAND_CS_DIST 0x80 +#define CFG_NAND_UPM_WRITE_CMD_OFS 0x20 +#define CFG_NAND_UPM_WRITE_ADDR_OFS 0x40 + +#define CFG_NAND_BR ((CFG_NAND0_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMB |\ + BRx_V) + +#define CFG_NAND_OR (MEG_TO_AM(CFG_NAND_SIZE) |\ + ORxU_BI |\ + ORxU_EHTR_8IDLE) + +#define CFG_NAND_SIZE 1 +#define CFG_NAND0_BASE 0x50000000 +#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST) + +#define CFG_MAX_NAND_DEVICE 4 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ + CFG_NAND2_BASE, \ + CFG_NAND3_BASE, \ + } + +#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)(adr)) = (__u8)d; } while(0) +#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)(adr))) +#define WRITE_NAND_UPM(d, adr, off) do \ +{ \ + volatile unsigned char *addr = (unsigned char *) (adr + off); \ + WRITE_NAND(d, addr); \ +} while(0) + +#endif /* CFG_CMD_NAND */ + +#define CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_PCI_PNP +#define CONFIG_EEPRO100 +#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_PCI_SCAN_SHOW +#endif + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if 0 +#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) + +# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) +#else +#define CFG_HRCW_MASTER (HRCW_BPS11 | HRCW_ISB111 | HRCW_BMS | HRCW_MODCK_H0111) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR_60x (BCR_EBM|BCR_NPQM0|BCR_NPQM2) /* 60x mode */ +#define BCR_APD01 0x10000000 +#define CFG_BCR_SINGLE (BCR_APD01|BCR_ETM) /* 8260 mode */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +#define CFG_SIUMCR_LOW (SIUMCR_DPPC00) +#define CFG_SIUMCR_HIGH (SIUMCR_DPPC00 | SIUMCR_ABE) +#else +#define CFG_SIUMCR (SIUMCR_DPPC00) +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR SCCR_DFBRG01 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 32 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + * 2 60x UPMB 8 bit NAND + * 3 60x UPMC 8 bit CAN + * + */ + +/* Initialize SDRAM + */ +#undef CFG_INIT_LOCAL_SDRAM /* No SDRAM on Local Bus */ + +#define SDRAM_MAX_SIZE 0x20000000 /* max. 512 MB */ + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ + +#define CFG_MPTPR 0x4000 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + * In fact, the address is rather configuration data presented to the SDRAM on + * its address lines. Because the address lines may be mux'ed externally either + * for 8 column or 9 column devices, some bits appear twice in the 8260's + * address: + * + * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | + * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | + * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | + * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | + * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | + *----------------------------------------------------------------------------- + */ +#define CFG_MRS_OFFS 0x00000110 + +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_8_CLK |\ + ORxG_TRLX) + +/* SDRAM on TQM8272 can have either 8 or 9 columns. + * The number affects configuration values. + */ + +/* Bank 1 - 60x bus SDRAM + */ +#define CFG_PSRT 0x20 /* Low Value */ +/* #define CFG_PSRT 0x10 Fast Value */ +#define CFG_LSRT 0x20 /* Local Bus */ +#ifndef CFG_RAMBOOT +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM CFG_OR1_8COL + +/* SDRAM initialization values for 8-column chips + */ +#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A7 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + + +/* SDRAM initialization values for 9-column chips + */ +#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A5 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A7 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + +#define CFG_OR1_10COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A4 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_10COL (PSDMR_PBI |\ + PSDMR_SDAM_A17_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A4 |\ + PSDMR_RFRC_6_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + +#define PSDMR_RFRC_66MHZ_SINGLE 0x00028000 /* PSDMR[RFRC] at 66 MHz single mode */ +#define PSDMR_RFRC_100MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 100 MHz single mode */ +#define PSDMR_RFRC_133MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 133 MHz single mode */ +#define PSDMR_RFRC_66MHZ_60X 0x00030000 /* PSDMR[RFRC] at 66 MHz 60x mode */ +#define PSDMR_RFRC_100MHZ_60X 0x00028000 /* PSDMR[RFRC] at 100 MHz 60x mode */ +#define PSDMR_RFRC_DEFAULT PSDMR_RFRC_133MHZ_SINGLE /* PSDMR[RFRC] default value */ + +#define PSDMR_PRETOACT_66MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 66 MHz single mode */ +#define PSDMR_PRETOACT_100MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 100 MHz single mode */ +#define PSDMR_PRETOACT_133MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 133 MHz single mode */ +#define PSDMR_PRETOACT_66MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 66 MHz 60x mode */ +#define PSDMR_PRETOACT_100MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 100 MHz 60x mode */ +#define PSDMR_PRETOACT_DEFAULT PSDMR_PRETOACT_133MHZ_SINGLE /* PSDMR[PRETOACT] default value */ + +#define PSDMR_WRC_66MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 66 MHz single mode */ +#define PSDMR_WRC_100MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 100 MHz single mode */ +#define PSDMR_WRC_133MHZ_SINGLE 0x00000010 /* PSDMR[WRC] at 133 MHz single mode */ +#define PSDMR_WRC_66MHZ_60X 0x00000010 /* PSDMR[WRC] at 66 MHz 60x mode */ +#define PSDMR_WRC_100MHZ_60X 0x00000010 /* PSDMR[WRC] at 100 MHz 60x mode */ +#define PSDMR_WRC_DEFAULT PSDMR_WRC_133MHZ_SINGLE /* PSDMR[WRC] default value */ + +#define PSDMR_BUFCMD_66MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 66 MHz single mode */ +#define PSDMR_BUFCMD_100MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 100 MHz single mode */ +#define PSDMR_BUFCMD_133MHZ_SINGLE 0x00000004 /* PSDMR[BUFCMD] at 133 MHz single mode */ +#define PSDMR_BUFCMD_66MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 66 MHz 60x mode */ +#define PSDMR_BUFCMD_100MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 100 MHz 60x mode */ +#define PSDMR_BUFCMD_DEFAULT PSDMR_BUFCMD_133MHZ_SINGLE /* PSDMR[BUFCMD] default value */ + +#endif /* CFG_RAMBOOT */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/alpr.h b/include/configs/alpr.h index bbe6b76bff..49027da5a4 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -166,8 +166,23 @@ "cp.b 100000 fffc0000 40000;" \ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ + "ethprime=ppc_4xx_eth3\0" \ + "ethact=ppc_4xx_eth3\0" \ + "autoload=no\0" \ + "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ + "actkernel=kernel2\0" \ + "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ + "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ + "rootfstype=jffs2 init=/sbin/init\0" \ + "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ + ";bootm 200000\0" \ + "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ + "addtty;bootm 200000\0" \ + "kernel1=run ipconfig load_fpga kernel1_mtd\0" \ + "kernel2=run ipconfig load_fpga kernel2_mtd\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTCOMMAND "run kernel2" #define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ @@ -291,6 +306,8 @@ /*----------------------------------------------------------------------- * Definitions for GPIO setup *-----------------------------------------------------------------------*/ +#define CFG_GPIO_SHUTDOWN (0x80000000 >> 6) +#define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9) #define CFG_GPIO_EREADY (0x80000000 >> 26) #define CFG_GPIO_REV0 (0x80000000 >> 14) #define CFG_GPIO_REV1 (0x80000000 >> 15) diff --git a/include/configs/idmr.h b/include/configs/idmr.h new file mode 100644 index 0000000000..48915b32e3 --- /dev/null +++ b/include/configs/idmr.h @@ -0,0 +1,197 @@ +/* + * Configuration settings for the iDMR board + * + * Based on MC5272C3, r5200 and M5271EVB board configs + * (C) Copyright 2006 Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * (C) Copyright 2006 Lab X Technologies <zachary.landau@labxtechnologies.com> + * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _IDMR_H +#define _IDMR_H + + +/* + * High Level Configuration Options (easy to change) + */ + +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5271 /* define processor type */ +#define CONFIG_IDMR /* define board type */ + +#undef CONFIG_WATCHDOG /* disable watchdog */ + +/* + * Default environment settings + */ +#define CONFIG_BOOTCOMMAND "run net_nfs" +#define CONFIG_BOOTDELAY 5 +#define CONFIG_BAUDRATE 19200 +#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_ETHADDR 00:06:3b:01:41:55 +#define CONFIG_ETHPRIME +#define CONFIG_IPADDR 192.168.30.1 +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_ROOTPATH +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.0.0 +#define CONFIG_HOSTNAME idmr +#define CONFIG_BOOTFILE /tftpboot/idmr/uImage +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root " \ + "filesystem over NFS; echo" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):" \ + "$(netmask):$(hostname):$(netdev):off panic=1\0" \ + "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;bootm $(kernel_addr) " \ + "$(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ethact=FEC ETHERNET\0" \ + "update=prot off ff800000 ff81ffff; era ff800000 ff81ffff; " \ + "cp.b 200000 ff800000 $(filesize);" \ + "prot on ff800000 ff81ffff\0" \ + "load=tftp 200000 $(u-boot)\0" \ + "u-boot=/tftpboot/idmr/u-boot.bin\0" \ + "" + +/* + * Commands' definition + */ +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ + CFG_CMD_PING | \ + CFG_CMD_NET | \ + CFG_CMD_MII) & \ + ~(CFG_CMD_LOADS | \ + CFG_CMD_LOADB)) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/* + * Configuration for environment, which occupies third sector in flash. + */ +#ifndef CONFIG_MONITOR_IS_IN_RAM +#define CFG_ENV_ADDR 0xff820000 +#define CFG_ENV_SECT_SIZE 0x10000 +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH +#else /* CONFIG_MONITOR_IS_IN_RAM */ +#define CFG_ENV_OFFSET 0x4000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_IS_IN_FLASH +#endif /* !CONFIG_MONITOR_IS_IN_RAM */ + +#define CFG_PROMPT "=> " +#define CFG_LONGHELP /* undef to save memory */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else /* !(CONFIG_COMMANDS & CFG_CMD_KGDB) */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif /* (CONFIG_COMMANDS & CFG_CMD_KGDB) */ + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_LOAD_ADDR 0x00100000 + +#define CFG_MEMTEST_START 0x400 +#define CFG_MEMTEST_END 0x380000 + +#define CFG_HZ (50000000 / 64) +#define CFG_CLK 100000000 + +#define CFG_MBAR 0x40000000 /* Register Base Addrs */ + +/* + * Ethernet + */ +#define FEC_ENET +#define CONFIG_NET_RETRY_COUNT 5 +#define CFG_ENET_BD_BASE 0x480000 +#define CFG_DISCOVER_PHY 1 +#define CONFIG_MII 1 + +/* + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x20000000 +#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_FLASH_BASE 0xff800000 + +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CFG_MONITOR_BASE 0x20000 +#else /* !CONFIG_MONITOR_IS_IN_RAM */ +#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#endif /* CONFIG_MONITOR_IS_IN_RAM */ + +#define CFG_MONITOR_LEN 0x20000 +#define CFG_MALLOC_LEN (256 << 10) +#define CFG_BOOTPARAMS_LEN (64*1024) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* FLASH organization */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CFG_FLASH_ERASE_TOUT 1000 + +#define CFG_FLASH_SIZE 0x800000 +/* + * #define CFG_FLASH_USE_BUFFER_WRITE 1 + */ + +/* Cache Configuration */ +#define CFG_CACHELINE_SIZE 16 + +/* Port configuration */ +#define CFG_FECI2C 0xF0 +#endif /* _IDMR_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 00b92220c1..e7f0108892 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -188,7 +188,10 @@ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#endif /*----------------------------------------------------------------------- * I2C diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h index 9d3609a67d..09bbebdce8 100644 --- a/include/configs/spc1920.h +++ b/include/configs/spc1920.h @@ -44,19 +44,19 @@ #define CONFIG_BAUDRATE 19200 /* use PLD CLK4 instead of brg */ -#undef CFG_SPC1920_SMC1_CLK4 +#define CFG_SPC1920_SMC1_CLK4 #define CONFIG_8xx_OSCLK 10000000 /* 10 MHz oscillator on EXTCLK */ #define CONFIG_8xx_CPUCLK_DEFAULT 50000000 #define CFG_8xx_CPUCLK_MIN 40000000 #define CFG_8xx_CPUCLK_MAX 133000000 -#define CFG_RESET_ADDRESS 0xf8000000 +#define CFG_RESET_ADDRESS 0xC0000000 #define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_LAST_STAGE_INIT - -#if 1 +#if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ @@ -83,12 +83,13 @@ #ifndef CONFIG_COMMANDS #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_ASKENV \ + | CFG_CMD_DATE \ | CFG_CMD_ECHO \ | CFG_CMD_IMMAP \ | CFG_CMD_JFFS2 \ | CFG_CMD_PING \ | CFG_CMD_DHCP \ - | CFG_CMD_IMMAP \ + | CFG_CMD_I2C \ | CFG_CMD_MII) /* & ~( CFG_CMD_NET)) */ @@ -193,13 +194,39 @@ #define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#ifdef CFG_CMD_DATE +# define CONFIG_RTC_DS3231 +# define CFG_I2C_RTC_ADDR 0x68 +#endif + /*----------------------------------------------------------------------- * I2C configuration */ #if (CONFIG_COMMANDS & CFG_CMD_I2C) -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */ -#define CFG_I2C_SLAVE 0x7F +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ + +#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */ +#define CFG_I2C_SLAVE 0xFE + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ #endif /*----------------------------------------------------------------------- @@ -220,7 +247,7 @@ *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ -#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#define CFG_SIUMCR (SIUMCR_FRC) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 @@ -283,7 +310,7 @@ * FLASH timing: */ #define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \ - OR_SCY_3_CLK | OR_EHTR | OR_BI) + OR_SCY_6_CLK | OR_EHTR | OR_BI) #define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) #define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) @@ -330,7 +357,56 @@ MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */ -/* PLD CS5 */ +/* + * DSP Host Port Interface CS3 + */ +#define CFG_SPC1920_HPI_BASE 0x90000000 +#define CFG_PRELIM_OR3_AM 0xF8000000 + +#define CFG_OR3 (CFG_PRELIM_OR3_AM | \ + OR_G5LS | \ + OR_SCY_0_CLK | \ + OR_BI) + +#define CFG_BR3 ((CFG_SPC1920_HPI_BASE & BR_BA_MSK) | \ + BR_MS_UPMA | \ + BR_PS_16 | \ + BR_V); + +#define CFG_MAMR (MAMR_GPL_A4DIS | \ + MAMR_RLFA_5X | \ + MAMR_WLFA_5X) + +#define CONFIG_SPC1920_HPI_TEST + +#ifdef CONFIG_SPC1920_HPI_TEST +#define HPI_REG(x) (*((volatile u16 *) (CFG_SPC1920_HPI_BASE + x))) +#define HPI_HPIC_1 HPI_REG(0) +#define HPI_HPIC_2 HPI_REG(2) +#define HPI_HPIA_1 HPI_REG(0x2000008) +#define HPI_HPIA_2 HPI_REG(0x2000008 + 2) +#define HPI_HPID_INC_1 HPI_REG(0x1000004) +#define HPI_HPID_INC_2 HPI_REG(0x1000004 + 2) +#define HPI_HPID_NOINC_1 HPI_REG(0x300000c) +#define HPI_HPID_NOINC_2 HPI_REG(0x300000c + 2) +#endif /* CONFIG_SPC1920_HPI_TEST */ + +/* + * Ramtron FM18L08 FRAM 32KB on CS4 + */ +#define CFG_SPC1920_FRAM_BASE 0x80100000 +#define CFG_PRELIM_OR4_AM 0xffff8000 +#define CFG_OR4 (CFG_PRELIM_OR4_AM | \ + OR_ACS_DIV2 | \ + OR_BI | \ + OR_SCY_4_CLK | \ + OR_TRLX) + +#define CFG_BR4 ((CFG_SPC1920_FRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V); + +/* + * PLD CS5 + */ #define CFG_SPC1920_PLD_BASE 0x80000000 #define CFG_PRELIM_OR5_AM 0xffff8000 @@ -343,10 +419,6 @@ #define CFG_BR5_PRELIM ((CFG_SPC1920_PLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V); -/* #define CFG_PLD_BASE 0x30000000 */ -/* #define CFG_OR5_PRELIM 0xffff1110 */ -/* #define CFG_BR5_PRELIM 0x30000401 */ - /* * Internal Definitions * diff --git a/include/configs/v38b.h b/include/configs/v38b.h index 554a7a41b8..e19591d299 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -39,6 +39,7 @@ #define CONFIG_NETCONSOLE 1 #define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */ #define CFG_XLB_PIPELINING 1 /* gives better performance */ @@ -101,7 +102,7 @@ CFG_CMD_IRQ | \ CFG_CMD_JFFS2 | \ CFG_CMD_MII | \ - CFG_CMD_SDRAMi | \ + CFG_CMD_SDRAM | \ CFG_CMD_DATE | \ CFG_CMD_USB | \ CFG_CMD_FAT) @@ -135,7 +136,7 @@ "preboot=echo;echo Type \"run flash_nfs\" to mount root " \ "filesystem over NFS; echo\0" \ "netdev=eth0\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "ramargs=setenv bootargs root=/dev/ram rw wdt=off \0" \ "addip=setenv bootargs $(bootargs) " \ "ip=$(ipaddr):$(serverip):$(gatewayip):" \ "$(netmask):$(hostname):$(netdev):off panic=1\0" \ @@ -144,7 +145,7 @@ "$(ramdisk_addr)\0" \ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ + "nfsroot=$(serverip):$(rootpath) wdt=off\0" \ "hostname=v38b\0" \ "ethact=FEC ETHERNET\0" \ "rootpath=/opt/eldk-3.1.1/ppc_6xx\0" \ diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h index 58717f8a60..911a52dbcf 100644 --- a/include/configs/yellowstone.h +++ b/include/configs/yellowstone.h @@ -302,6 +302,20 @@ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH CFG_FLASH_BASE +#define CFG_CPLD 0x80000000 + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03017300 +#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000) + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x04814500 +#define CFG_EBC_PB2CR (CFG_CPLD | 0x18000) + +/*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 6e942abcaa..2cc18db9a5 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -307,6 +307,20 @@ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH CFG_FLASH_BASE +#define CFG_CPLD 0x80000000 + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03017300 +#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000) + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x04814500 +#define CFG_EBC_PB2CR (CFG_CPLD | 0x18000) + +/*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ diff --git a/include/flash.h b/include/flash.h index 9c57cbc427..8b7e824cca 100644 --- a/include/flash.h +++ b/include/flash.h @@ -51,6 +51,7 @@ typedef struct { ushort device_id2; /* extended device id */ ushort ext_addr; /* extended query table address */ ushort cfi_version; /* cfi version */ + ushort cfi_offset; /* offset for cfi query */ #endif } flash_info_t; diff --git a/include/mpc8260.h b/include/mpc8260.h index ff52a7b38b..d9dd92d9a5 100644 --- a/include/mpc8260.h +++ b/include/mpc8260.h @@ -35,7 +35,15 @@ #endif #ifndef CPU_ID_STR #if defined(CONFIG_MPC8272_FAMILY) +#ifdef CONFIG_MPC8247 +#define CPU_ID_STR "MPC8247" +#elif defined CONFIG_MPC8248 +#define CPU_ID_STR "MPC8248" +#elif defined CONFIG_MPC8271 +#define CPU_ID_STR "MPC8271" +#else #define CPU_ID_STR "MPC8272" +#endif #else #define CPU_ID_STR "MPC8260" #endif @@ -66,6 +74,7 @@ #define BCR_EXDD 0x00000400 /* External Master Delay Disable*/ #define BCR_ISPS 0x00000010 /* Internal Space Port Size */ + /*----------------------------------------------------------------------- * PPC_ACR - 60x Bus Arbiter Configuration Register 4-28 */ @@ -168,6 +177,7 @@ #define SIUMCR_MMR10 0x00008000 /* - " - */ #define SIUMCR_MMR11 0x0000c000 /* - " - */ #define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/ +#define SIUMCR_ABE 0x00000400 /* Address output buffer impedance*/ /*----------------------------------------------------------------------- * IMMR - Internal Memory Map Register 4-34 diff --git a/include/ppc440.h b/include/ppc440.h index 50f4ec403b..91cff414af 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -887,12 +887,14 @@ /* PLB4 Arbiter - PowerPC440EP Pass1 */ #define PLB4_DCR_BASE 0x080 +#define plb4_acr (PLB4_DCR_BASE+0x1) #define plb4_revid (PLB4_DCR_BASE+0x2) -#define plb4_acr (PLB4_DCR_BASE+0x3) #define plb4_besr (PLB4_DCR_BASE+0x4) #define plb4_bearl (PLB4_DCR_BASE+0x6) #define plb4_bearh (PLB4_DCR_BASE+0x7) +#define PLB4_ACR_WRP (0x80000000 >> 7) + /* Nebula PLB4 Arbiter - PowerPC440EP */ #define PLB_ARBITER_BASE 0x80 @@ -3284,26 +3286,26 @@ typedef struct { unsigned long add; /* gpio core base address */ /* * Macros for accessing the indirect EBC registers */ -#define mtebc(reg, data) mtdcr(ebccfga,reg);mtdcr(ebccfgd,data) -#define mfebc(reg, data) mtdcr(ebccfga,reg);data = mfdcr(ebccfgd) +#define mtebc(reg, data) { mtdcr(ebccfga,reg);mtdcr(ebccfgd,data); } +#define mfebc(reg, data) { mtdcr(ebccfga,reg);data = mfdcr(ebccfgd); } /* * Macros for accessing the indirect SDRAM controller registers */ -#define mtsdram(reg, data) mtdcr(memcfga,reg);mtdcr(memcfgd,data) -#define mfsdram(reg, data) mtdcr(memcfga,reg);data = mfdcr(memcfgd) +#define mtsdram(reg, data) { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } +#define mfsdram(reg, data) { mtdcr(memcfga,reg);data = mfdcr(memcfgd); } /* * Macros for accessing the indirect clocking controller registers */ -#define mtclk(reg, data) mtdcr(clkcfga,reg);mtdcr(clkcfgd,data) -#define mfclk(reg, data) mtdcr(clkcfga,reg);data = mfdcr(clkcfgd) +#define mtclk(reg, data) { mtdcr(clkcfga,reg);mtdcr(clkcfgd,data); } +#define mfclk(reg, data) { mtdcr(clkcfga,reg);data = mfdcr(clkcfgd); } /* * Macros for accessing the sdr controller registers */ -#define mtsdr(reg, data) mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data) -#define mfsdr(reg, data) mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd) +#define mtsdr(reg, data) { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } +#define mfsdr(reg, data) { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } #ifndef __ASSEMBLY__ |