diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/ML2.h | 257 |
1 files changed, 0 insertions, 257 deletions
diff --git a/include/configs/ML2.h b/include/configs/ML2.h deleted file mode 100644 index 4df9f4cbc5..0000000000 --- a/include/configs/ML2.h +++ /dev/null @@ -1,257 +0,0 @@ -/* - * ML2.h: ML2 specific config options - * - * Copyright 2002 Mind NV - * - * http://www.mind.be/ - * - * Author : Peter De Schrijver (p2@mind.be) - * - * Derived from : other configuration header files in this tree - * - * This software may be used and distributed according to the terms of - * the GNU General Public License (GPL) version 2, incorporated herein by - * reference. Drivers based on or derived from this code fall under the GPL - * and must retain the authorship, copyright and this license notice. This - * file is not a complete program and may only be used when the entire - * program is licensed under the GPL. - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405 1 /* This is a PPC405 CPU */ -#define CONFIG_4xx 1 /* ...member of PPC4xx family */ -#define CONFIG_ML2 1 /* ...on a ML2 board */ - -#define CONFIG_SYS_TEXT_BASE 0x18000000 -#define CONFIG_SYS_LDSCRIPT "board/ml2/u-boot.lds" - -#define CONFIG_ENV_IS_IN_FLASH 1 - -#ifdef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_FLASH -#else -#ifdef CONFIG_ENV_IS_IN_FLASH -#undef CONFIG_ENV_IS_IN_NVRAM -#endif -#endif - -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#if 1 -#define CONFIG_BOOTCOMMAND "bootm" /* autoboot command */ -#else -#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ -#endif - -#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image" - -#if 0 -#define CONFIG_BOOTARGS "root=/dev/nfs " \ - "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \ - "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4" -#else -#define CONFIG_BOOTARGS "root=/dev/mtdblock2 " \ - "console=ttyS0 console=tty" - -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_KGDB -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_JFFS2 - -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_RTC -#undef CONFIG_CMD_PCI -#undef CONFIG_CMD_I2C - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_SYS_CLK_FREQ 50000000 - -#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ - -/* - * I2C - */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_SPEED 400000 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ - -#define CONFIG_SYS_BASE_BAUD (3125000*16) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD -#define CONFIG_SYS_DUART_CHAN 0 -#define CONFIG_SYS_NS16550_COM1 0xa0001003 -#define CONFIG_SYS_NS16550_COM2 0xa0011003 -#define CONFIG_SYS_NS16550_REG_SIZE -4 -#define CONFIG_SYS_NS16550 1 -#define CONFIG_SYS_INIT_CHAN1 1 -#define CONFIG_SYS_INIT_CHAN2 1 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x18000000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* BEG ENVIRONNEMENT FLASH */ -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ -#endif -/* END ENVIRONNEMENT FLASH */ -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */ - -#ifdef CONFIG_ENV_IS_IN_NVRAM -#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ -#define CONFIG_ENV_ADDR \ - (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ -#endif - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF0000500 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00080000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=ml2-0" -#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)" -*/ - -#endif /* __CONFIG_H */ |