| Age | Commit message (Collapse) | Author |
|---|
|
That option is currently not used by any defconfig and could not be set
anymore since it became mandatory to used Kconfig when introducing new
options with U-Boot v2016.11 or commit eed921d92348 ("Kconfig: Add a
whitelist of ad-hoc CONFIG options") and commit 371244cb19f9 ("Makefile:
Give a build error if ad-hoc CONFIG options are added").
It was also not considered when fixing build warnings in
commit 39ac34473f3c ("cmd_mtdparts: use 64 bits for flash size,
partition size & offset") and could probably not be compiled anyway
after commit dfe64e2c8973 ("mtd: resync with Linux-3.7.1"), which
renamed some members of struct mtd_info … so it was probably broken
since then, which was U-Boot v2013.07-rc1.
However it still seems to work, see example output below:
U-Boot 2019.10-00035-g06a9b259ca-dirty (Oct 30 2019 - 14:03:44 +0100)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
Model: ***
DRAM: 128 MiB
NAND: 256 MiB
Loading Environment from NAND... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net: eth0: ethernet@f8008000
Hit keys 'tt' to stop autoboot (3 seconds).
U-Boot> mtdparts
device nand0 <atmel_nand>, # parts = 8
#: name size net size offset mask_flags
0: bootstrap 0x00040000 0x00040000 0x00000000 1
1: uboot 0x000c0000 0x000c0000 0x00040000 1
2: env1 0x00040000 0x00040000 0x00100000 0
3: env2 0x00040000 0x00040000 0x00140000 0
4: fpga_led 0x00040000 0x00040000 0x00180000 1
5: reserved 0x00040000 0x00040000 0x001c0000 1
6: rootfs_rec 0x03200000 0x03200000 0x00200000 1
7: filesystem 0x0cc00000 0x0cb80000 (!) 0x03400000 0
active partition: nand0,0 - (bootstrap) 0x00040000 @ 0x00000000
defaults:
mtdids : nand0=atmel_nand
mtdparts: mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env1),256k(env2),256k(fpga_led)ro,256k(reserved)ro,50M(rootfs_rec)ro,-(filesystem)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
This declaration is not used anywhere in the whole tree. There is a
function 'mtd_id_parse()' which was renamed from 'id_parse()' in
commit 68d7d65100e8 ("Separate mtdparts command from jffs2"), but that
function is not used (anymore?) in cmd nand and build is fine without
that declaration, so it's probably just safe to remove.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
As part of disabling caches MMU as well gets disabled. But MMU is not
available on all armv7 cores like R5F. So disable MMU only if it is
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
'make tests' on a 32bit ARM system leads to
In file included from ../common/cli_hush.c:79:
../include/malloc.h:364:7: error: conflicting types for ‘memset’
void* memset(void*, int, size_t);
^~~~~~
In file included from ../include/compiler.h:126,
from ../include/env.h:12,
from ../common/cli_hush.c:78:
../include/linux/string.h:103:15:
note: previous declaration of ‘memset’ was here
extern void * memset(void *,int,__kernel_size_t);
^~~~~~
In file included from ../common/cli_hush.c:79:
../include/malloc.h:365:7: error: conflicting types for ‘memcpy’
void* memcpy(void*, const void*, size_t);
^~~~~~
In file included from ../include/compiler.h:126,
from ../include/env.h:12,
from ../common/cli_hush.c:78:
../include/linux/string.h:106:15:
note: previous declaration of ‘memcpy’ was here
extern void * memcpy(void *,const void *,__kernel_size_t);
^~~~~~
According to the U-Boot coding style guide common.h should be the first
include.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
When full malloc is enabled and SYS_MALLOC_F is also enabled, the simple
pre-reloc heap is used before relocation. In this case, calloc() uses
the MALLOC_ZERO macro to zero out the allocated memory. However, since
this macro is specially crafted for the dlmalloc implementation, it
does not always work for simple malloc.
For example, when allocating 16 bytes via simple malloc, only the first
12 bytes get zeroed out. The last 4 bytes will remain untouched.
This is a problem for DM drivers that are allocated before relocation:
memory allocated via 'platdata_auto_alloc_size' might not be set to
zero, resulting in bogus behaviour.
To fix this, use 'memset' instead of 'MALLOC_ZERO' to zero out memory
that compes from simple malloc.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
As SPL_SPI_FLASH_SUPPORT cannot work without SPL_SPI_SUPPORT, fix
dependencies to prevent enabling SPI flash support without basic SPI
support.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
The default implementation of ERR_PTR/PTR_ERR maps errno values at the
and of the address range (e.g. -EINVAL/-22 gets 0xFFFFFFEA).
For socfpga gen5 SPL, this doesn't really work, as the heap is nearly
at the end of the 32 bit address range.
This patch adjusts the ERR_PTR_OFFSET to map errno values into the range
of the Boot ROM, which should not be used for valid pointers.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
This patch changes ERR_PTR/PTR_ERR to use CONFIG_ERR_PTR_OFFSET to map
errno values into a pointer region that cannot contain valid pointers.
IS_ERR and IS_ERR_OR_NULL have to be converted to use PTR_ERR, too,
for this to work.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Some U-Boot pointers have redundant information, so we can use a scheme
where we can return either an error code or a pointer with the same
return value. The default implementation just casts the pointer to a
number, however, this may fail on platforms where the end of the address
range is used for valid pointers (e.g. 0xffffff00 is a valid heap pointer
in socfpga SPL). For such platforms, this value provides an upper range
of those error pointer values - up to 'MAX_ERRNO' bytes below this value
must be unused/invalid addresses.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Provide optimized memcpy_{from,to}io() and memset_io(). This is required
when moving large amount of data to and from IO regions such as IP
registers or accessing memory mapped flashes.
Code is borrowed from Linux Kernel v5.4.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
API_dev_write(va_list ap) is currently lacking the write support
to storage devices because, historically, those devices did not
implement block_write()
The solution has been tested by loading and booting a (patched)
GRUB instance in a QEMU vexpress-a9 environment. The disk write
operations were triggered with GRUB's save_env command.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- mpc85xx, socrates: Add dts, enable DM support, fix warnings, disable
video
|
|
- Re-enable LLVM tests in Travis and add them to GitLab and Azure
|
|
Now that we have again fixed the problems that building with clang
exposes, enable these tests on Azure and GitLab-CI as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When using the OVERRIDE variable we need to pass -O to buildman as well
to use the "override" option to buildman.
Fixed: e9500f49ea35 ("travis: Use buildman for building with clang")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Newer versions of LLVM-7 will provide an unused function warning over
console_doenv() in the case of SYS_CONSOLE_IS_IN_ENV not being enabled
as can be the case in SPL. Add guards around this function.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
To add usb-3.0 support to peripheral device add BOS & SS capability
descriptors to gadget composite framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
|
|
Add a new bcdDevice entry for Cadence USB gadget controller similar to
other controller and add gadget_is_cdns3() macro as well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add driver to handle TI specific wrapper for Cadence USB3 controller
present on J721e SoC. Based on Linux driver for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Implement udc_set_speed() callback to limit Controller's speed to
high-speed/full-speed when working with gadgets that are high-speed or
full-speed only
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[jjhiblot@ti.com: Add PHY support]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
This patch was copied from kernel commit: 67fdfda4a99ed.
Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver because that will just fail.
So here introduce a new optional ->udc_set_speed() method which can be
implemented by interested UDC drivers to achieve this purpose.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add match_ep() op to usb_gadget_ops similar to Linux kernel which is
useful in finding a suitable ep match for the function driver. This will
avoid adding more gadget_is_xxx() handling code to usb_ep_autoconfig().
Also sync usb_ep_caps struct thats is usually used in the match_ep()
callback by the gadget controller driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Import for_each_set_bit() and associated macros and functions from
Linux. This is useful in parsing interrupt registers and take action on
each bit that is set.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Import list_first_entry_or_null() macro from Linux that would be used
by Cadence USB driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
imx targets are defined in arch/arm/mach-imx/Makefile.
Some of them are dependent on targets defined in main
Makefile. For the Makefile in arch/arm/mach-imx this
targets must be finished before the imx targets are
build, if not you get for example the error:
make -f /home/hs/abb/mainlining/u-boot/scripts/Makefile.build obj=arch/arm/mach-imx u-boot-dtb.imx
make[2]: *** No rule to make target 'u-boot-fit-dtb.bin', needed by 'u-boot-dtb.imx'. Stop.
make[1]: *** [/home/hs/abb/mainlining/u-boot/Makefile:1123: u-boot-dtb.imx] Error 2
make[1]: *** Waiting for unfinished jobs....
make[1]: Leaving directory '/work/hs/compile/u-boot/aristainetos2_defconfig'
make: *** [Makefile:148: sub-make] Error 2
compile failed
In above case of CONFIG_MULTI_DTB_FIT is defined, the
u-boot-dtb.imx is dependent on the u-boot-fit-dtb.bin
which may is not build yet ...
I could reproduce this error on a travis build also if
I build an out-of-tree build on a local machine with a
build directory on a "slow" slow storage device. If
building the same source target with a build dir on a
fast storage device, the build works.
I found no solution to tell the arch/arm/mach-imx/Makefile
to find the targets in main Makefile, if there is a way
this would be the better fix.
I solved it by adding a IMX_DEPS var, which holds a list
of main u-boot targets, which must be finished, before
calling imx targets and fixed the build for imx
targets which enabled CONFIG_MULTI_DTB_FIT.
I think it is just luck, that imx targets with
CONFIG_OF_SEPARATE enabled build, because the
u-boot-dtb.imx target depends on u-boot-dtb.bin
which gets build early enough before starting with
u-boot-dtb.imx. May this targets should be fixed too.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
- DFU updates
- USB Storage updates
|
|
- fsl_esdhc driver cleanup
- fsl_esdhc_imx driver improvement and compatible string update
|
|
add DM PCI support on the socrates board.
use PCIE_FSL now.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
switch to DM_SERIAL support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
enable DM I2C support for the socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
disable video, as not really needed longer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add some defines and get rid of USB warning.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
enable CONFIG_DM for the socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add u-boot specific dtsi file for socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Also, add me as board maintainer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
suppress warning:
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
With python3 we're now tripping over a long-standing problem with how we
add to the buildman file with some toolchains. We cannot have multiple
toolchain-alias sections as that leads to a parse error.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Update to latest libfdt and pylibfdt, with added size control
Update binman, dtoc, patman, buildman to Python 3
Update move_config, rkmux, microcode_tool to Python 3
|
|
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make DM and non-DM code clear using below structure.
#if !CONFIG_IS_ENABLED(DM_MMC)
<non-DM_MMC code>
#else
<DM_MMC code>
#endif
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Drop redundant code for non-removable feature. "non-removable" property
has been read in mmc_of_parse().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
