summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-02-24armv8/fsl-lsch3: Add support for second DDR clockYork Sun
FSL-LSCH3 platforms can have multiple DDR clocks. LS2085A has one clock for general DDR controlers, and another clock for DP-DDR. DDR driver needs to change to support multiple clocks. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24driver/ddr/fsl: Add workround for erratumn A008514York Sun
Erratum A008514 workround requires writing register eddrtqcr1 with value 0x63b20002. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24driver/ddr/fsl: Add workaround for A008336York Sun
Erratum A008336 requires setting EDDRTQCR1[2] in DDRC DCSR space for 64-bit DDR controllers. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24driver/ddr/fsl: Adjust CAS to preamble override for emulatorYork Sun
On ZeBu emulator, CAS to preamble overrides need to be set to satisfy the timing. This only impact platforms with CONFIG_EMU. These should be set before MEM_EN is set. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24armv8/fsl-lsch3: Add fdt-fixup for clock frequency of the DUART nodesBhupesh Sharma
This patch adds the fdt-fixup logic for the clock frequency of the NS16550A related device tree nodes. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24armv8/ls2085a: Enable cluster timebase for all clustersYork Sun
LS2085A and its variants can have up to four clusters. It is safe to enable timebase for all even some may be disabled. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24armv8/fsl-lsch3: Convert flushing L3 to assembly to avoid using stackYork Sun
Flushing L3 cache in CCN-504 requries d-cache to be disabled. Using assembly function to guarantee stack is not used before flushing is completed. Timeout is needed for simualtor on which CCN-504 is not implemented. Return value can be checked for timeout situation. Change bootm.c to disable dcache instead of simply flushing, required by flushing L3. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24ARMv8/fsl-lsch3: Patch cpu node properties in DT for online coresArnab Basu
U-Boot should only add "enable-method" and "cpu-release-address" properties to the "cpu" node of the online cores. Signed-off-by: Arnab Basu <arnab.basu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24armv8/fsl-lsch3: Change normal memory shareabilityYork Sun
According to hardware implementation, a single outer shareable global coherence group is defined. Inner shareable has not bee enabled. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24fsl-ch3/lowlevel: TZPC and TZASC programming to configure non-secure accessesBhupesh Sharma
This patch ensures that the TZPC (BP147) and TZASC-400 programming happens for LS2085A SoC only when the desired config flags are enabled and ensures that the TZPC programming is done to allow Non-secure (NS) + secure (S) transactions only for DCGF registers. The TZASC component is not present on LS2085A-Rev1, so the TZASC-400 config flag is turned OFF for now. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24usb: musb-new: omap2430: Reset the MUSB controller earlyPaul Kocialkowski
When booting from USB peripheral boot, the bootrom will not properly deinit the MUSB controller, which doesn't clearly indicate an USB disconnection to the host and leaves U-Boot to deal with the state of the previous USB session. On some host controller drivers (e.g. xhci_hcd), this ends up in a failure during set address, caused by the lack of proper disconnection notification. Resetting the controller early in U-Boot notifies the host of the disconnection and doesn't hurt other use cases. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@ti.com>
2015-02-24exynos: usb: make dwc3_set_mode to staticJoonyoung Shim
The dwc3_set_mode function is used only in drivers/usb/host/xhci-exynos5.c so make it to static. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
2015-02-24Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
2015-02-23Merge branch 'master' of git://git.denx.de/u-boot-mmcTom Rini
2015-02-23mmc: sdhci: fix bus width switching on Samsung SoCsMatt Reimer
Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on Samsung SoCs using SDHCI_QUIRK_USE_WIDE8. These SoCs report controller version 2.0 yet they support 8-bit bus widths. If 8-bit mode was previously enabled and then an operation like "mmc dev" caused a switch back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures. This problem was manifested by "mmc dev" timing out. Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
2015-02-23mmc: print SD/eMMC type for inited mmc devicesPrzemyslaw Marczak
Depending on the boot priority, the eMMC/SD cards, can be initialized with the same numbers for each boot. To be sure which mmc device is SD and which is eMMC, this info is printed by 'mmc list' command, when the init is done. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-02-23mmc: exynos dwmmc: check boot mode before init dwmmcPrzemyslaw Marczak
Before this commit, the mmc devices were always registered in the same order. So dwmmc channel 0 was registered as mmc 0, channel 1 as mmc 1, etc. In case of possibility to boot from more then one device, the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device. This can be achieved by init boot device as first, so it will be always registered as mmc 0. Thanks to this, the 'saveenv' command will work fine for all mmc boot devices. Exynos based boards usually uses mmc host channels configuration: - 0, or 0+1 for 8 bit - as a default boot device (usually eMMC) - 2 for 4bit - as an optional boot device (usually SD card slot) And usually the boot order is defined by OM pin configuration, which can be changed in a few ways, eg. - Odroid U3 - eMMC card insertion -> first boot from eMMC - Odroid X2/XU3 - boot priority jumper By this commit, Exynos dwmmc driver will check the OM pin configuration, and then try to init the boot device and register it as mmc 0. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Simon Glass <sjg@chromium.org> Cc: Akshay Saraswat <akshay.s@samsung.com>
2015-02-23sunxi: mmc: Always declare High Capacity capabilityHans de Goede
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13 tablet, so always set it thereby fixing this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-23mmc: exynos_dw_mmc: use the exynos specific data structureJaehoon Chung
Clksel value is exynos specific value. It removed "clksel_val" into dwmci_host and created the "dwmci_exynos_priv_data" structure for exynos specific data. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23mmc: exynos_dw_mmc: set to clksel_val into board-init functionJaehoon Chung
"clksel_val" is assigned to property of mmc or defined value. But it doesn't write at initial sequence. There is a reason that get the wrong source-clock value. This patch fixed it. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23mmc: dw_mmc: fixed the wrong bit controlJaehoon Chung
If mode is not DDR-mode, then it needs to clear it. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23mmc: Implement SD/MMC versioning properlyPantelis Antoniou
The SD/MMC version scheme was buggy when dealing with standard major.minor.change cases. Fix it by using something similar to the linux's kernel versioning method. Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Reported-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com>
2015-02-23warp: Add initial WaRP Board supportOtavio Salvador
The WaRP Board is a Wearable Reference Plaform. The board features: - Freescale i.MX6 SoloLite processor with 512MB of RAM - Freescale FXOS8700CQ 6-axis Xtrinsic sensor - Freescale Kinetis KL16 MCU - Freescale Xtrinsic MMA955xL intelligent motion sensing platform The board implements a hybrid architecture to address the evolving needs of the wearables market. The platform consists of a main board and an example daughtercard with the ability to add additional daughtercards for different usage models. For more information about the project, visit: http://www.warpboard.org/ Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2015-02-23imx: mx6sl: Extend USDHC SD2 pins to support 8-wire useOtavio Salvador
This adds the DATA[4-7] and RST pin definitions. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-02-23mmc: fsl_esdhc: Add support to force VSELECT setOtavio Salvador
Some boards cannot do voltage negotiation but need to set the VSELECT bit forcely to ensure it to work at 1.8V. This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-02-23mmc: fsl_esdhc: Add CMD11 support to switch to 1.8VOtavio Salvador
This adds support to switch to 1.8V in case CMD11 succeeds. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Marek Vasut <marex@denx.de>
2015-02-23imx:mx6slevk implement power init boardPeng Fan
Implement power_init_board and related I2C interface configuration. After adding this, uboot can successfully detect and configure pmic. " U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01) CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 " Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-23imx:mx6slevk add pmic and i2c configurationPeng Fan
Add pmic and i2c configuration in board header file. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-23imx:mx6sl add I2c pad settingsPeng Fan
A few pad settings are I2C1 Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-23board: tbs2910: Gate clock when switching async clock muxesSoeren Moch
According to the i.MX6Q Reference Manual, clocks must be gated when switching input clocks of async clock muxes. So use clock gates. Avoid ldb_di0_ipu clock, because there is no clock gate for this signal. There have never been any complaints about problems with the old code, but the new approach is in line with the recommendations in the manual. Signed-off-by: Soeren Moch <smoch@web.de>
2015-02-21Merge git://git.denx.de/u-boot-sunxiTom Rini
2015-02-21sunxi: Machine id hack to prevent loading buggy sunxi-3.4 kernelsSiarhei Siamashka
Right now U-Boot supports the CONFIG_OLD_SUNXI_KERNEL_COMPAT option, which makes it go out of its way in limiting the selection of PLL clock frequencies and PMIC voltages in order not to upset outdated buggy sunxi-3.4 kernel releases. And if the CONFIG_OLD_SUNXI_KERNEL_COMPAT option is not set, then booting such old kernels exhibits various failures at runtime. This is very user unfriendly, and there were already several incidents when people wasted their time being hit by these runtime failures and trying to debug them. The right solution is not to add hacks and workarounds to the mainline U-Boot, but to fix these bugs in the sunxi-3.4 kernel. And in fact, the updated sunxi-3.4 kernels already exist. Still we need to follow the 'Principle of Least Surprise' and U-Boot needs to ensure that the old buggy kernels are not getting happily booted when the CONFIG_OLD_SUNXI_KERNEL_COMPAT option is not set. And this patch addresses this particular issue. This patch makes U-Boot store the 'compatibility revision' number in the top 4 bits of the machine id and pass it to the kernel. The old buggy kernels will fail to load with a very much googlable error message on the serial console (the "r1 = 0x100010bb" part of it): "Error: unrecognized/unsupported machine ID (r1 = 0x100010bb)" This error message can be documented in the linux-sunxi wiki with proper explanations about how to resolve this situation and where to get the necessary bugfixes for the sunxi-3.4 kernel. The fixed sunxi-3.4 kernels implement a revision compatibility check and clear the top 4 bits of the machine id if everything is alright. By accepting the machine id with the bits 31:28 set to 1, the sunxi-3.4 kernel effectively certifies that it has the PLL5 clock speed and AXP209 DCDC3 voltage fixes applied. It is still possible to set the CONFIG_OLD_SUNXI_KERNEL_COMPAT option in U-Boot if the user desires to use an outdated unpatched sunxi-3.4 kernel. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-21sunxi: Set the /chosen/stdout-path fdt property for sunxi boardsHans de Goede
While discussing with some people how to get the Linux kernel to do the right thing wrt sending output to both the serial console and the hdmi out / lcd screen when booting on ARM devices, Grant Likely pointed out that there already is a solution for this. All we need to do is set the /chosen/stdout-path fdt property, and if no console= arguments were specified on the kernel commandline the kernel will honor this and add this device as a console (next to the primary video output on hdmi). And u-boot already has support for setting this, all we need to do is define OF_STDOUT_PATH and then everything will just work ootb, without people needing to meddle with adding console= arguments in extlinux.conf . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com>
2015-02-21sunxi: Fix sun5i mbus speed when booting old kernelsHans de Goede
Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz, halving the mbus frequency, so set it to 300 MHz ourselves and base the mbus divider on that. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21sunxi: musb: Check Vbus-det before enabling otg port powerHans de Goede
Sending out 5V when there is a charger connected to the otg port is not a good idea, so check for this and error out. Note this commit currently breaks otg support on the q8h tablets, as we need to do some magic with the pmic there to get vbus info, this is deliberate (better safe then sorry), fixing this is on my TODO list. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21sunxi: Add support for the UTOO P66 tabletHans de Goede
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips lcd screen, 512MB RAM & 4GB emmc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21sunxi: mmc: Always declare High Capacity capabilityHans de Goede
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13 tablet, so always set it thereby fixing this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-21rpi: add support for Raspberry Pi 2 model BStephen Warren
USB doesn't seem to work yet; the controller detects the on-board Hub/ Ethernet device but can't read the descriptors from it. I haven't investigated yet. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21bcm2836 SoC support (used in Raspberry Pi 2 model B)Stephen Warren
The bcm2835 and bcm2836 are essentially identical, except: - The CPU is an ARM1176 v.s. a quad-core Cortex-A7. - The physical address of many IO controllers has moved. Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH), update the existing bcm2835 code to handle the minor differences, and plumb it into the ARMv7 CPU architecture. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21bcm2835/rpi: add SPDX license tags for some filesStephen Warren
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21ARM: prepare for including <mach/*.h>Masahiro Yamada
This commit adds $(srctree)/arch/arm/$(machdirs)/include/mach to the headers search path. It allows us to replace "#include <asm/arch/foo.h>" with "#include <mach/foo.h>". As "#include <asm/arch/foo.h>" is still supported, we can modify each file one by one. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-21ARM: keystone: move SoC headers to mach-keystone/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-keystone/* -> arch/arm/mach-keystone/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
2015-02-21ARM: orion5x: move SoC headers to mach-orion5x/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-orion5x/* -> arch/arm/mach-orion5x/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-02-21ARM: nomadik: move SoC headers to mach-nomadik/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-nomadik/* -> arch/arm/mach-nomadik/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com> Cc: Alessandro Rubini <rubini@unipv.it>
2015-02-21ARM: kirkwood: move SoC headers to mach-kirkwood/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-kirkwood/* -> arch/arm/mach-kirkwood/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-02-21ARM: davinci: move SoC headers to mach-davinci/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-davinci/* -> arch/arm/mach-davinci/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
2015-02-21ARM: at91: move SoC headers to mach-at91/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-at91/* -> arch/arm/mach-at91/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-21kbuild: prepare for moving headers into mach-*/include/machMasahiro Yamada
In U-Boot, SoC-specific headers are placed in arch/$(ARCH)/include/asm/arch-$(SOC) and a symbolic link to that directory is created at the early stage of the build process. Creating and removing a symbolic link during the build is not preferred. In fact, Linux Kernel did away with include/asm-$(ARCH) directories a long time time ago. As for ARM, now it is possible to collect SoC sources into arch/arm/mach-$(SOC). It is also reasonable to move SoC headers into arch/arm/mach-$(SOC)/include/mach. This commit prepares for that. If the directory arch/$(ARCH)/mach-$(SOC)/include/mach exists, a symbolic to that directory is created. Otherwise, a symbolic link to arch/$(ARCH)/include/asm/arch-$(SOC) or arch-$(CPU) is created. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-21ARM: keystone: move SoC sources to mach-keystoneMasahiro Yamada
Move arch/arm/cpu/armv7/keystone/* -> arch/arm/mach-keystone/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
2015-02-21ARM: versatile: move SoC sources to mach-versatileMasahiro Yamada
Move arch/arm/cpu/arm926ejs/versatile/* -> arch/arm/mach-versatile/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
generated by cgit (git 2.34.1) at 2025-01-18 11:12:07 +0000