| Age | Commit message (Collapse) | Author |
|---|
|
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Fixes: ed784ac3822b ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
|
|
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- spi cs accessing slaves (Bin Meng)
- spi prevent overriding established bus (Marcin Wojtas)
- support speed in spi command (Marek Vasut)
- add W25N01GV spinand (Robert Marko)
- move cadence_qspi to use spi-mem (Vignesh Raghavendra)
- add octal mode (Vignesh Raghavendra)
|
|
- Add Dialog DA9063 PMIC support
- s35392a RTC bugfix
- Allow for opt-in of removal of DTB properties from the resulting
binary.
|
|
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
|
|
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
The 3-bit "command", or register, is encoded within the device address.
Configure the device accordingly, and pass command in DM I2C read/write
calls correctly.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
If we didn't unbind the sata from block device, the same devices would
be added after sata remove,
This patch is to resolve this issue as below:
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
=> sata stop
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 2: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 3: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This shrinks the image size: all -3840.0 text -3840.0
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Soeren Moch <smoch@web.de>
|
|
This can be used for device tree size reduction similar as
CONFIG_OF_SPL_REMOVE_PROPS option. Some boards must pass the
built-in DTB unchanged to the kernel, thus we may not cut it
down unconditionally. Therefore enable the property removal
list option only if CONFIG_OF_DTB_PROPS_REMOVE is selected.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
TI's AM654 SoC has a Cadence OSPI IP. Add a new compatible string for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Linux has supported W25N01GV for a long time, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The 'sspi' command hard-coded 1 MHz bus frequency for all transmissions.
Allow changing that at runtime by specifying '@freq' bus frequency in Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Per sandbox_cs_info(), sandbox spi controller only supports chip
select 0. Current test case tries to locate devices on chip select
1, and any call to spi_get_bus_and_cs() or spi_cs_info() with cs
number 1 should not return 0.
This updates the test case to handle it correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add chip select number check in spi_find_chip_select().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
|
|
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-clk
- Various clock fixes and enhancements
|
|
Since frac_pll_init() is only used in this file, change it to 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Function init_usb_clk() is not used anywhere, so it can simply be deleted.
This was detected by the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype
for ‘init_usb_clk’ [-Wmissing-prototypes]
void init_usb_clk(void)
^~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_av_set_rate(). If it is 0, let's return with -EINVAL.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Guard 'mfd==0' to prevent 'divide by zero' issue in
clk_pplv3_av_get_rate(). If it is 0, let's return with EIO since mfd
should never be 0 at all.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_sys_get_rate(). If it is 0, let's return with -EINVAL.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
m68k needs block cache list initialized after relocation.
Other architectures must not be involved.
Fixing regression related to:
commit 1526bcce0f7285087621e16e6720636d01839da8
("common: add blkcache init")
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
|
|
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930cc, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Patch-to: Simon Glass <sjg@chromium.org>
|
|
- Libre Computer ALL-H3-IT/ALL-H5-CC board (Chen-Yu Tsai)
- Allwinner R40 Ethernet, usb phy enablement (Andre Przywara)
- Sunxi auto load from 128KB MMC offset (Andre Przywara)
- Orange Pi Win Ethernet phy enablement (Jernej Skrabec)
|
|
Orange Pi Win has gigabit ethernet port, but default U-Boot
configuration for that board enabled ethernet driver but
didn't enable realtek phy.
Fix that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Since commit 067e0b9684d4 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
dev_read_addr_ptr returns NULL on error, not FDT_ADDR_T_NONE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
This header was missing a couple of include dependencies when included on its
own.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
is enabled
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
It will ease debug when uclass_get_device_by_name failed with
more error info printed out.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.
This commit change the return type of mtk_clk_find_parent_rate to
ulong.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
|
|
Updates and fixes for ls1028a, lx2160a, ls1012a, ls1021a, ls2080a,
ls1088a platforms:
- lx2-rev2 pcie support, enetc related updates, layerscape-pcie fixes
|
|
- Enable fastboot on some MediaTek platforms
- DMA enchancements
- Assorted bugfixes
|
|
This patch adds a prototype for the weak function
board_mtdparts_default().
It solves one warning when compiling with W=1 on stm32mp1 board:
board/st/stm32mp1/stm32mp1.c:
warning: no previous prototype for 'board_mtdparts_default'
[-Wmissing-prototypes]
void board_mtdparts_default(const char **mtdids,
const char **mtdparts)
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The blkcache_read() routine returns 1 (true) to indicate that a block was
found in the cache and returned, or 0 if not.
Signed-off-by: Eric Nelson <eric@nelint.com>
|
|
There is a typo in meerkat96 MAINTAINERS email address. Fix it.
Reported-by: Carl Gelfand <carl@novtech.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
