summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-05-03net: ethoc: add write_hwaddr supportThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: altera_tse: add write_hwaddr supportThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: fec_mxc: add write_hwaddr supportHeiko Schocher
tested on the magnesium board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net:kirkwood_egiga.c: MAC addresses programming using write_hwaddrPrafulla Wadaskar
Added a new function kwgbe_write_hwaddr for programming egiga controller's hardware address. This function will be called for each egiga port being used Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03Program net device MAC addresses after initializingBen Warren
Add a new function to the eth_device struct for programming a network controller's hardware address. After all network devices have been initialized and the proper MAC address for each has been determined, make a device driver call to program the address into the device. Only device instances with valid unicast addresses will be programmed. Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de> Tested-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-03net: add altera triple speeds ethernet mac driverThomas Chou
This driver supports the Altera triple speeds 10/100/1000 ethernet mac. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: add opencore 10/100 ethernet mac driverThomas Chou
This patch ports the opencore 10/100 ethernet mac driver ethoc.c from linux kernel to u-boot. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03smc911x driver frame alignment patchValentin Yakovenkov
SMSC911x chips have alignment function to allow frame payload data (which comes after 14-bytes ethernet header) to be aligned at some boundary when reading it from fifo (usually - 4 bytes boundary). This is done by inserting fake zeros bytes BEFORE actual frame data when reading from SMSC's fifo. This function controlled by RX_CFG register. There are bits that represents amount of fake bytes to be inserted. Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long, so we need to add 2 fake bytes to get payload data aligned at 4-bytes boundary. Linux driver does this by adding IP_ALIGNMENT constant (defined at skb.h) when calculating fifo data length. All network subsystem of Linux uses this constant too when calculating different offsets. But u-boot does not use any packet data alignment, so we don't need to add anything when calculating fifo data length. Moreover, driver zeros the RX_CFG register just one line up, so chip does not insert any fake data at the beginig. So calculated data length is always bigger by 1 word. It seems that at almost every packet read we get an underflow condition at fifo and possible corruption of data. Especially at continuous transfers, such as tftp. Just after removing this magic addition, I've got tftp transfer speed as it aught to be at 100Mbps. It was really slow before. It seems that fifo underflow occurs only when using byte packing on 32-bit blackfin bus (may be because of very small delay between reads). Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Kirkwood_egiga.c bugfixes for rx pathPrafulla Wadaskar
Cosmetic changes: Few comments updated Functionality: Rx packet frame size is programming should be done when port is in disabled state. this is corrected Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fec_mxc.c: Fix MX27 FEC MAC validity checkEric Jarrige
Fix MX27 FEC logic to check validity of the MAC address in fuse. Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change. Signed-off-by: Eric Jarrige <jorasse@armadeus.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03tsec: Wait for both RX and TX to stopAndy Fleming
When gracefully stopping the controller, the driver was continuing if *either* RX or TX had stopped. We need to wait for both, or the controller could get into an invalid state. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: dm9000x: use standard I/O accessorsMike Frysinger
The current dm9000x driver accesses its memory mapped registers directly instead of using the standard I/O accessors. This can cause problems on Blackfin systems as the accesses can get out of order. So convert the direct volatile dereferences to use the normal in/out macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03mpc512x_fec: Move PHY initialization from probe into init routine.Detlev Zundel
This saves the autonegotation delay when not using ethernet in U-Boot Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fec_mxc don't use internal eeprom on MX25John Rigby
Avoid using the internal eeprom on MX25 like MX51 already does. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fix lockup in mcfmii/mii_discover_phy() in case communication failsWolfgang Wegner
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-0383xx: UEC: Added support for bitBang MII driver access to PHYsRichard Retanubun
This patch enabled support for having PHYs on bitBang MII and uec MII operating at the same time. Modeled after the MPC8360ADS implementation. Added the ability to specify which ethernet interfaces have bitbang SMI on the board header file. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03./net/net.c - make Microsoft dns servers happy with random_port() numbersRobin Getz
For some reason, (which I can't find any documentation on), if U-Boot gives a port number higher than 17500 to a Microsoft DNS server, the server will reply to port 17500, and U-Boot will ignore things (since that isn't the port it asked the DNS server to reply to). This fixes that by ensuring the random port number is less than 17500. Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03Remove unused "local_crc32" function.Detlev Zundel
For code archeologists, this is a nice example of copy and paste history. Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Trivial coding style issue with empty for statementDetlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Kirkwood_egiga.c: fixed build warningsPrafulla Wadaskar
This patch fixes following build warnings for kirkwood_egiga.c kirkwood_egiga.c: In function "kwgbe_init": kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules kirkwood_egiga.c: In function "kwgbe_recv": kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-01Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/masterWolfgang Denk
2010-05-01Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2010-04-29ppc4xx: Fix APC405 build breakageStefan Roese
This patch fixes APC405 build, by defining CONFIG_PPC4XX_I2C. This is needed since the move of the PPC4xx I2C driver into the drivers/i2c directory. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-04-29ppc4xx: Add support for ICON board (PPC440SPe)Stefan Roese
This patch adds support for the Mosaix Technologies, Inc. ICON board, based on the AppliedMicro (AMCC) PPC440SPe. It's equipped with an SODIMM (512MB standard) and 64MByte of NOR FLASH. Support for the onboard SM502 will be added later. Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-29ppc4xx: Add missing APC405 to MAKEALLStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-04-29Fix typos in Korat board console outputLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org> Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-28QONG: Adapt flash addresses and mtdparts to grown image sizeWolfgang Denk
Also enable HUSH shell. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-04-28mtdparts: get rid of custom DEBUG macro, use debug()Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-04-28mtdparts: fix write through NULL pointerWolfgang Denk
The "mtdparts add" command wrote through a NULL pointer - on many systems this went unnoticed (PowerPC has writable RAM there, some ARM systems have ROM where a write has no effect), but on arm1136 (i.MX31) it crashed the system. Add appropriate checks. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-04-28ubifsmount fails due to not initialized listStefano Babic
ubifsmount is not working and causes an access with a pointer set to zero because the ubifs_fs_type is not initialized correctly. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-28Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
2010-04-28Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2010-04-27MX31: Added LCD support for QONG moduleStefano Babic
Added support for LCD and splash image to the QONG module. The supported display is VBEST-VGG322403. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-27Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxxWolfgang Denk
2010-04-27Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2010-04-27Merge branch 'next' of git://git.denx.de/u-boot-niosWolfgang Denk
2010-04-26ppc: Split MPC83xx SERDES code from MPC85xx/MPC86xx/QorIQKumar Gala
The MPC83xx SERDES control is different from the other FSL PPC chips. For now lets split it out so we can standardize on interfaces for determining of a device on SERDES is configured. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-26mpc85xx: Add the ability to set LCRR[CLKDIV] to improve R/W speed of flashLan Chunhe
Signed-off-by: Lan Chunhe <b25806@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-2685xx: clean up the io_sel for PCI express of P1022Dave Liu
clean up the wrong io_sel for PCI express according to latest manual. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-2685xx/socrates: Remove NFS support to fit image size.Detlev Zundel
This fixes an overflow during the link phase. Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-2685xx: Fix compile warningKumar Gala
cpu.c: In function 'checkcpu': cpu.c:47: warning: unused variable 'gur' Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-2685xx: Convert cpu_init_f code to use out_be32 for LBC registersKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl_sata: Move the snoop bit to another placeDave Liu
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT is moved to bit28. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl_sata: Add the workaround for errata SATA-A001Dave Liu
After power on, the SATA host controller of P1022 Rev1 is configured in legacy mode instead of the expected enterprise mode. Software needs to clear bit[28] of HControl register to change to enterprise mode after bringing the host offline. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl-ddr: Add extra cycle to turnaround timesDave Liu
Add an extra cycle turnaround time to read->write to ensure stability at high DDR frequencies. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26fsl-ddr: add the macro for Rtt_Nom definitionDave Liu
add the macro definition for Rtt_Nom termination value for DDR3 Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26ppc/p4080: Add p4080 DEVDISR2 & SRDS_PLLCR0 definesKumar Gala
Added some needed fines and some misc additional defines used by p4080 initialization. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26ppc/p4080: Extend the GUTS memory mapDave Liu
Extend pin control and clock control to GUTS memory map Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26ppc/p4080: Fix synchronous frequency calculationsSrikanth Srinivasan
When DDR is in synchronous mode, the existing code assigns sysclk frequency to DDR frequency. It should be synchronous with the platform frequency. CPU frequency is based on platform frequency in synchronous mode. Also fix: * Fixes the bit mask for DDR_SYNC (RCWSR5[184]) * Corrects the detection of synchronous mode. Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26ppc/85xx: Fixup PCI nodes for P1_P2_RDBKumar Gala
While we had ft_pci_board_setup it wasn't being called by ft_board_setup. Fix that so we actually update the device tree PCI nodes on P1_P2_RDB boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2025-01-07 21:50:32 +0000