| Age | Commit message (Collapse) | Author |
|---|
|
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add the pre-reloc DT markers to clock nodes needed in SPL and early
U-Boot stages. This is required to let the Arria10 clock driver start
early and provide clock information for UART and SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The variables removed in this patch are never used, they are only ever
assigned and then waste precious memory. Drop both the assignment and
the variables.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The L4SP and MMC clock precalculation is specific to Gen5, it is not
needed on Arria10/Stratix10. Isolate it to Gen5 until there is a proper
clock driver for Gen5, at which point this will go away completely.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Bind fixed clock driver to the base clock instantiated in the handoff
DT and use DM clock framework to get their clock rate. This replaces
the ad-hoc DT parsing present thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Enable DM ethernet framework on Arria10, so that the designware GMAC
can be probed from DT as it should be.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Remove code from the reset manager that is never called.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
The UART reset handling is now done via reset framework using the
SoCFPGA reset driver. The UART console assignment is done using the
DM and console framework. Nuke all this comlexity, since it is just
duplicating the same functionality, badly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the DM I2C framework on Arria10, so that the DM capable
Designware I2C driver can handle the reset via DM reset framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Enable the DM reset framework and DM reset driver on Arria10 both
in U-Boot and in SPL. This lets U-Boot parse reset control from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The A10 SoCDK is missing the I2C bus alias, so DM I2C cannot assign
the I2C bus a bus number. Add the missing alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The I2Cx resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The UART0 and UART1 resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The Altera reset manager block must be available very early on, since
it controls ie. UART resets. Flag it as pre-reloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The restructuring of the SPL dropped registration of the FPGA in SPL,
readd it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Fixes: c859f2a77d98 ("arm: socfpga: Restructure the SPL file")
|
|
Some of the code for low level system initialization in SPL's
board_init_f() and U-Boot's arch_early_init_r() is the same,
so let's combine it into a single function called from both.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Add new drivers
Add Christophe Kerello and myself as maintainers
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This patch fix the following warnings for for stm32f429
evaluation and discovery boards:
unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add ADC device tree node. This allows to get analog conversions on
stm32mp157.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This commit enables CONFIG_BLK and removes USB_STORAGE which is awaiting
proper implementation for current U-Boot interfaces. Additionally the
console selection is now handled by Kconfig and no longer needs to be in
the config header. CONFIG_SYS_MALLOC_F_LEN=0x2000 was added to sync with
other boards. CONFIG_SPL_BLK and CONFIG_SPL_DM_MMC are disabled because
they currently do not allow the OMAP3-EVM (OMAP34XX) to actually boot.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
The recv variable in sandbox_tpm2_fill_buf() is a pointer on a pointer
of a char array. It means accessing *recv is the char array pointer
itself while **recv is the first character of that array. There is no
need for such indirection here, so simplify the code.
Simplifying things will make the last assignment right: "*recv = NULL"
is now correct. The issue has been found by the following Coverity
Scan report:
CID 183371: Incorrect expression (UNUSED_VALUE)
Assigning value "4UL" to "*recv" here, but that stored value is overwritten before it can be used.
232 *recv += sizeof(rc);
233
234 /* Add trailing \0 */
235 *recv = NULL;
While at simplifying things, use '\0' instead of NULL when adding an
empty char at the end of the buffer.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The second check on pcr_map in sandbox_tpm2_xfer() is wrong. It should
check for pcr_map not being empty. Instead, it is a pure copy/paste of
the first check which is redundant.
This has been found thanks to a Coverity Scan report:
CID 183370: Memory - illegal accesses (UNINIT)
Using uninitialized value "pcr_index".
put_unaligned_be32(tpm->pcr_extensions[pcr_index], recv);
This is because pcr_index is initialized only if the user input is
correct, ie. at least one valid bit is set in pcr_map.
Fix the second check and also initialize pcr_index to 0 (which is
harmless in case of error) to make Coverity Scan happy.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add scattered driver files around the source tree
that belongs to Snapdragon arch. Not sure why they
were not included in the first place.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
1. Add FIT support for DB410c defconfig.
2. Don't overwrite bootargs (they're already
defined in Linux device tree for DB410c.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
Change the way MAC address fixup is done:
1. Stop using LK handed device-tree and calculate
the MAC address our own.
2. Allow overriding the generated MACS with environment variables:
"wlanaddr" and "btaddr".
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
Add support for generation of unique MAC address
that is derived from board serial.
Algorithm for generation of MAC taken from LK.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
This commit adds a function to get the board
serial number.
In snapdragon it's actually the eMMC serial number.
Function added in a new file misc.c that will
include further snapdragon miscellaneous functions.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
Commit 1473b12ad0b3 ("lib: fdtdec: Update ram_base to store ram start
adddress") brings regression on STM32F7 which can't boot.
Use fdtdec_setup_mem_size_base() to setup memory base and size.
Use fdtdec_setup_memory_banksize() to setup memory bank base and size.
Reported-by: Mark Olsson <mark@markolsson.se>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Mark Olsson <mark@markolsson.se>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Add DISTRO_DEFAULT support to be able to boot on mmc
by default on boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add DISTRO_DEFAULT support to be able to boot on mmc
by default on boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add DISTRO_DEFAULT support to be able to boot on
mmc by default on boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add DISTRO_DEFAULT support to be able to boot on mmc
by default on boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Since commit bfea69ad2793 ("stm32f7: sdram: correct sdram
configuration as per micron sdram"), CONFIG_SYS_RAM_FREQ_DIV
flag is no more used, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove CONFIG_CMD_CACHE from include/configs/stm32h7xx.h
and enable it in stm32h7xx_defconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove CONFIG_CMD_CACHE from include/configs/stm32f746-disco.h
and enable it in stm32f746-disco_defconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Enable instruction and data caches.
Fix boot_sd command as since commit d409c962169b ("armv7m: disable
icache before linux booting"), instruction cache is automatically
disable before linux booting. "icache off" from boot_sd command
becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This flag is not used, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Since commit aa5e3e22f4d6 ("board: stm32: switch to DM STM32 timer")
SYS_CLK_FREQ is useless, remove it from stm32f4 and stm32f7 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use gd->bd->bi_dram[0].start initialized from DT instead of using
hardcoded CONFIG_SYS_SDRAM_BASE from config file.
Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In case the slow clock is not properly configured, the UTMI clock
cannot lock the PLL, because UPLLCOUNT will "wait X slow clock cycles".
In this case U-boot will loop indefinitely.
Added a timeout in this case, to start U-boot even if UTMI clock is
not enabled, so the user can use different media if needed, or investigate.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Move some configuration #defines that do not apply to other bcmstb
boards from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
|
|
Move the contents of prior_stage.h into bcmstb.h to prevent a build
failure when bcmstb.h is #include'ed before the asm/arch symbolic link
is present.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
|
|
Fix LibreSSL compilation for versions before v2.7.0.
Signed-off-by: Caliph Nomble <nomble@palism.com>
Reviewed-by: Jonathan Gray <jsg@jsg.id.au>
|
|
%s/dumm /dummy /
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
