summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-02-24powerpc/t2081qds: Add T2081 QDS board supportShengzhou Liu
T2081 QDS is a high-performance computing evaluation, development and test platform supporting the T2081 QorIQ Power Architecture processor. T2081QDS board Overview ----------------------- - T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz - 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC) - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving - Ethernet interfaces: - Two on-board 10M/100M/1G bps RGMII ports - Two 10Gbps XFI with on-board SFP+ cage - 1Gbps/2.5Gbps SGMII Riser card - 10Gbps XAUI Riser card - Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC - SerDes: - 8 lanes up to 10.3125GHz - Supports SGMII, HiGig, XFI, XAUI and Aurora debug, - IFC: - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - eSPI: - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) - USB: - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - PCIe: - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - eSDHC: - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and voltage translators - I2C: - Four I2C controllers. - UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24powerpc/t208x: some update to support t2081Shengzhou Liu
- fix serdes definition for t2081. - fix clock speed for t2081. - update ids, as CONFIG_FSL_SATA_V2 is needed only for t2080, T2081 has no SATA. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24boards.cfg: Keep arc entries sortedFabio Estevam
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg" in order to keep arc entries sorted. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-02-24arm: delete unused macro CONFIG_ARCH_DEVICE_TREEMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Rajeshwari Birje <rajeshwari.s@samsung.com> Cc: Inderpal Singh <inderpal.singh@linaro.org>
2014-02-24x86: coreboot: delete unused coreboot/config.mkMasahiro Yamada
HOSTCFLAGS_autoconf.mk.dep was added by commit 422322f but it has never been used. Cc: Vadim Bendebury <vbendeb@chromium.org> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-24power: fix: Do not execute pmic command when not all necessary parameters ↵Łukasz Majewski
are passed Lack of this check resulted in a data abort when CPU tried to execute the following command (without further mandatory input): 'pmic MAX77686_PMIC'. Only the 'pmic list' command requires one passed parameter. Other require at least two valid parameters for correct operation. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2014-02-24kbuild: fix SPL link bug when USE_PRIVATE_LIBGCC is "yes"Masahiro Yamada
Commit 6825a95 (kbuild: use Linux Kernel build scripts) changed the behavior of linkage when USE_PRIAVATE_LIBGCC is defined as "yes". (It dropped arch/arm/lib/eabi_compat.o from the target library.) Affected boards are all Tegra boards. This commit gets back the same behavior as before Kbuild series. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
2014-02-24part_efi: fix protective mbr struct allocationHector Palacios
The calloc() call was allocating space for the sizeof the struct pointer rather than for the struct contents. Besides, since this buffer is passed to mmc for writing and some platforms may use cache, the legacy_mbr struct should be cache-aligned. Signed-off-by: Hector Palacios <hector.palacios@digi.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2014-02-24Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-02-22board: bcm28155_ap: Add board filesDarwin Rambo
Add support for the bcm28155_ap reference board. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22mmc: kona: Add Kona mmc driverDarwin Rambo
Add support for the Kona SDHCI found on Broadcom mobile SoCs. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22i2c: kona: Add Kona I2C driverDarwin Rambo
Add support for the Kona I2C controller found on Broadcom mobile SoCs. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22gpio: kona: Add Kona gpio driverDarwin Rambo
Add support for the Kona GPIO controller found on Broadcom mobile SoCs. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22arch: bcm281xx: Initial commit of bcm281xx architecture codeDarwin Rambo
Add bcm281xx architecture support code including a clock framework and chip reset. Define register block base addresses for the bcm281xx architecture and create an empty gpio header file required when CONFIG_CMD_GPIO is set. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22arch: kona: Initial commit of kona-common architecture codeDarwin Rambo
The Kona architecture is present on a number of Broadcom mobile SoCs including the bcm281xx family of chips. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Steve Rae <srae@broadcom.com> Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22ARM: rpi_b: rework boot scripts, enable sysbootStephen Warren
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as much as possible. This will aid in a future patch which will create a common header e.g. config_distro_bootcmd.h. While at it, enable booting from extlinux.conf using the sysboot command. The iteration and componentization currently makes a little more sense for Tegra than RPi, but I'd still like to keep the two as similar as possible. USB and networking support is coming to the RPi in due course, and it'll all make more sense then anyway. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-21ti814x: Fix illegal use of FP ops in clock_ti814x.cMåns Rullgård
The function pll_sigma_delta_val uses "float" data which is not correct. The exact "why" of this mangling is lost to history, but this changes us to equivalent non-FP math to get the same results. Reported-by: Wolfgang Denk <wd@denx.de> Acked-by: Matt Porter <mporter@linaro.org>
2014-02-21omap4_common: config: remove I2C for SPL modeNishanth Menon
Commit 6789e84ecaa8f45d053084e08c381284a04abff7 (i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework) intended to make I2C driver compatible with latest changes. It unfortunately has had a impact on size on SPL as well. For example on SDP4430, 32032 bytes before/MLO 35416 bytes after/MLO With this mentioned commit, MLO stops booting on SDP4430 as only 32K is accessible for non-secure (bootloader) s/w on GP devices and the size increase to 56K fails boot. On the latest u-boot commit e7be18225fbea76d1f0034b224f0d1e60f07cfcf, MLO is now at size 35592 bytes, However, I2C is not necessary for SPL to function as we use SR_I2C for controlling the PMIC. Disabling I2C reduces MLO to 32224 bytes which allows OMAP4 GP platform to boot up. Since this is common for all OMAP4 platforms, remove the need for I2C for SPL builds in the common config. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Sricharan R <r.sricharan@ti.com>
2014-02-21dra7xx_evm: Enable GPT commandsTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21am43xx_evm: Enable GPT commandsTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21am335x_evm: Enable GPT commandsTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21arm: omap: cm_t35: Remove CONFIG_SYS_BOOTMAPSZ to fix FDT Linux bootingStefan Roese
With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting results in this error: Booting using the fdt blob at 0x81f00000 Loading Kernel Image ... OK ERROR: Failed to allocate 0x1189d bytes below 0x80004000. device tree - allocation error FDT creation failed! hanging...### ERROR ### Please RESET the board ### Removing this define solves this issue. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com>
2014-02-21DRA7: fix ABB efuse offset for OPP_NOMNishanth Menon
commit 194dd74ad919e57026f385aaab7f89acf7ea79ef (DRA7: add ABB setup for MPU voltage domain) Made an offset typo error by using 0x4A003B24 as the efuse offset for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and 0x4A003B20 is for OPP_NOM. Fix the same. Reported-by: Praveen Rao <prao@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
2014-02-21ARM: OMAP4: fix DDR timings for OMAP4430 ES2.0Janne Grunau
DDR timings were broken since 47abc3df701d8bc26f311350aa523fc1d0f8ad4e for PandaBoard EA1. Signed-off-by: Janne Grunau <j@jannau.net>
2014-02-21OMAP3: fix default environment for mcx boardStefano Babic
Patch allows to load a script at the startup from MMC. Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-02-21omap3: fix pinmux for mcx boardStefano Babic
New hardware version cannot recognize the SD-Card because the SYS_NRESWARM, set as GPIO, does not guarantee the required reset time. Change the pin function back to enable the SYS_NRESWARM signal driven by the SOC. Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-02-21OMAP3: add missing gpio clock init and fix NAND SPL for mcx boardStefano Babic
Patch contains the same fixes as commit 4b9b2c300a23ca4a85811918dc92e822a9571a87 (missing CONFIG_OMAP3_GPIO_2) and commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC). Same issues are relevant for the mcx board, too. Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-02-21arm: omap3: Fix tao3530/omap3_ha SPL boot hangup (GPIO clocks not enabled)Stefan Roese
Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on tao3530. Since some gpio input's are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2014-02-21ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator controlDave Gerlach
Schematic indicates GPIO5_7 is to be used for VTT regulator control rather than GPIO0_21 so modify enable_vtt_regulator to reflect this. Without this some boards will experience DDR3 corruption and fail to boot. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [trini: Rework patch against mainline] Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21Add support for B&R KWB MotherboardHannes Petermaier
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at> Cc: trini@ti.com
2014-02-21board: Add support for B&R T-Series MotherboardHannes Petermaier
Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-02-21am335x: Initial support for Silica Pengwyn boardLothar Felten
This patch add support for the Silica Pengwyn board [1] The board is based on a TI AM3354 CPU [2] All jumpers removed it will boot from the SDcard, the console is on UART1 accessible via the FDTI -> USB. The on board NAND flash is supported and can act as boot medium, depending on jumper settings. USB Host, USB Device and Ethernet are also provided but untested. [1] http://www.silica.com/product/silica-pengwyn-board.html [2] http://www.ti.com/product/am3354 Signed-off-by: Lothar Felten <lothar.felten@gmail.com> [trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused spi0_pin_mux from Pengwyn support] Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21ubifs: fix checkpatch warningKaricheri, Muralidharan
Fix the following checkpatch warning:- WARNING: externs should be avoided in .c files Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
2014-02-21common, itest: pass u-boot env variables to itest.sHeiko Schocher
compare two U-Boot Environment variables with itest.s, example: => print tmp ver tmp=U-Boot 2013.10-g75e ver=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => print check_ub_ver check_ub_ver=if itest.s \${tmp} == \${ver}; then echo equal; else echo diff ;fi => run check_ub_ver diff => setenv tmp U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => print tmp ver tmp=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX ver=U-Boot 2013.10-g75eb4bc (Jan 21 2014 - 10:35:39)MPC83XX => run check_ub_ver equal Signed-off-by: Heiko Schocher <hs@denx.de>
2014-02-21common, ubi: add ubi check volumename commandHeiko Schocher
check with this ubi command, if a UBI volume with "volumename" exists in current ubi device. Signed-off-by: Heiko Schocher <hs@denx.de>
2014-02-21boards.cfg: Delete the equivalent entriesMasahiro Yamada
There are some entries which produce the same binaries: - ep8248E is equivalent to ep8248 - MPC8360ERDK_66 is equivalent to MPC8360ERDK - Adder87x/AdderUSB is equivalent to Adder - EVB64260_750CX is equivalent to EVB64260 I also notice - Lite5200 is equivalent to icecube_5200 - Lite5200_LOWBOOT is equivalent to icecube_5200_LOWBOOT - Lite5200_LOWBOOT08 is equivalent to icecube_5200_LOWBOOT08 But I am keeping them. (Wolfgang suggested to do so because Lite5200* are referenced in misc documents.) Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-21boards.cfg: Place "-" in the 8th field if it is the same as 7thMasahiro Yamada
The 8th field of boards.cfg takes the form: <board config name>[:comma separated config options] We should describe explicitely the 8th field only when it is necessary to do so. Specify "-" in the 8th field if it is the same as 7th field. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-21ext4fs: Add ext4 extent cache for read operationsIonut Nicu
In an ext4 filesystem, the inode corresponding to a file has a 60-byte area which contains an extent header structure and up to 4 extent structures (5 x 12 bytes). For files that need more than 4 extents to be represented (either files larger than 4 x 128MB = 512MB or smaller files but very fragmented), ext4 creates extent index structures. Each extent index points to a 4KB physical block where one extent header and additional 340 extents could be stored. The current u-boot ext4 code is very inefficient when it tries to load a file which has extent indexes. For each logical file block the code will read over and over again the same blocks of 4096 bytes from the disk. Since the extent tree in a file is always the same, we can cache the extent structures in memory before actually starting to read the file. This patch creates a simple linked list of structures holding information about all the extents used to represent a file. The list is sorted by the logical block number (ee_block) so that we can easily find the proper extent information for any file block. Without this patch, a 69MB file which had just one extent index pointing to a block with another 6 extents was read in approximately 3 minutes. With this patch applied the same file can be read in almost 20 seconds. Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
2014-02-21SMC91111: Fix compilation warningsBhupesh Sharma
This patch fixes the following warning messages coming out of 'drivers/net/smc91111.h' when compiled for 'vexpress_aemv8a': warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Currently this issue seems to surface when SMSC is compiled for 64-bit ARMv8 platforms, so the change is protected under CONFIG_ARM64, so that it doesn't break other existing platforms. In addition this patch tries to fix some checkpatch errors and warnings (others related to camel-casing and volatile usage will be addressed by a later patch). This fix has been tested on both ARMv8 foundation model v1 and v2. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-02-21kbuild: fix errors of 'make *tags' and 'make cscope'Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Nishanth Menon <nm@ti.com>
2014-02-21kbuild: a minor optimization of "make clobber"Masahiro Yamada
The pattern rule "MLO*" can delete both MLO and MLO.byteswap. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-21.gitignore: ignore boot images by pattern rule /u-boot*Masahiro Yamada
U-Boot supports various boot images for various SoCs. It is annoying to modify .gitignore file every time we add/delete boot images. Fortunately, there is a simple rule: Those with file name prefix "u-boot" at the top directory are all generated files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-21Fix memory commands for 64-bit platformsYork Sun
For aarch64, unsigned long is 64-bit data. Memory commands should be fixed with u32 for 32-bit address access. To be clear, ushort is replace with u16, u_char is replaced with u8. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Wolfgang Denk <wd@denx.de>
2014-02-21pxe: prepend fdtdir to DTB name irrespective of sourceStephen Warren
The directory name from an fdtdir directive in a PXE config file should always be pre-pended to the DTB filename; it shouldn't matter whether the DTB filename came from the $fdtfile environment variable, or whether it was constructed dynamically from ${soc}-${board}.dtb. Fix the code to always prepend the directory name. Reported-by: Dennis Gilmore <dennis@ausil.us> Fixes: c61d94d86035 ("pxe: implement fdtdir extlinux.conf tag") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Dennis Gilmore <dennis@ausil.us> Tested-by: Dennis Gilmore <dennis@ausil.us>
2014-02-21fix address of error message in mtest commandDavid Feng
This patch deal with error message of mtest command. When test failed, the mtest command will output error information that include memory address and value. But the address field is not correct or misleading. Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-02-21common: Add get_effective_memsize() to memsize.cYork Sun
This function has been around for powerpc. It is used for systems with memory more than CONFIG_MAX_MEM_MAPPED. In case of non-contiguous memory, this feature can limit U-boot to one block without going over the limit. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-21driver/ddr: Add 256 byte interleaving supportYork Sun
Freescale LayerScape SoCs support controller interleaving on 256 byte size. This interleaving is mandoratory. Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-21Driver/ddr: Add support of different DDR base addressYork Sun
DDR base address has been the same from the view of core and DDR controllers. This has changed for Freescale ARM-based SoCs. Controllers setup DDR memory in a contiguous space and cores view it at separated locations. Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-21driver/ddr: Change Freescale ARM DDR driver to support both big and little ↵York Sun
endian Initially it was believed the DDR controller on Freescale ARM would have big endian. But some platform will have little endian. Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-21common: Remove invalid endianess conversionChristian Eggers
do_bootm_standanlone() calls ntohl(images->ep) which is wrong because endianess conversion has already been done: do_bootm() \-do_bootm_states() +-bootm_find_os() | \-images.ep = image_get_ep(); | \-uimage_to_cpu(hdr->ih_ep); \-boot_selected_os() \-do_bootm_standanlone() Without this conversion the code works correctly at least on AT91SAM9G45. On big endian systems there should be no difference after applying this patch because uimage_to_cpu(x) and ntohl(x) both expand to 'x'. Signed-off-by: Christian Eggers <ceggers@gmx.de>
generated by cgit (git 2.34.1) at 2024-12-25 06:11:51 +0000