summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-05-26mips: ath79: ar933x: Fix ethernet PHY mismatchWills Wang
We need reset the Ethernet Switch analog part before operation, or the build-in Ethernet PHY don't work. Signed-off-by: Wills Wang <wills.wang@live.com> Acked-by: Marek Vasut <marex@denx.de>
2016-05-26mips: Drop JZ4740 remnantsMarek Vasut
Remove the remnants of JZ4740 support. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Paul Burton <paul.burton@imgtec.com>
2016-05-26mips: Allow overriding start.S in SPLMarek Vasut
Certain chips, like the JZ47xx, have extreme size constraints on the SPL size and require custom start.S . Allow overriding the start.S the same way ARM MXS does it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Paul Burton <paul.burton@imgtec.com>
2016-05-26MIPS: Move CONFIG_SYS_TEXT_BASE to KconfigPaul Burton
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board Kconfig files matching what was present in their config headers. This will make it cleaner to conditionalise the value for Malta based on 32 vs 64 bit builds. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-26malta: Use device model & tree for UARTPaul Burton
Make use of device model & device tree to probe the UART driver. This is the initial step in bringing Malta up to date with driver model, and allows for cleaner handling of the different I/O addresses for different system controllers by specifying the ISA bus address instead of a translated memory address. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-26malta: Tidy up UART address selectionPaul Burton
The address of the UART differs based upon the system controller because it's actually within the I/O port region, which is in a different location for each system controller. Rather than handling this as 2 UARTs with the correct one selected at runtime, use I/O port accessors for the UART such that access to it gets translated into the I/O port region automatically. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-26dm: ns16550: Don't map_physmem for I/O portsPaul Burton
If the UART is to be accessed using I/O port accessors (inb & outb) then using map_physmem doesn't make sense, since it operates in a different memory space. Remove the call to map_physmem when CONFIG_SYS_NS16550_PORT_MAPPED is defined, allowing I/O port addresses to not be mangled by the incorrect mapping. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-25fdt: Document the rest of struct of_busPaul Burton
Provide some documentation for the fields of struct of_bus, for consistency with that provided for the new match field. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-25fdt: Support for ISA bussesPaul Burton
Support ISA busses in much the same way as Linux does. This allows for ISA bus addresses to be translated, and only if CONFIG_OF_ISA_BUS is selected in order to avoid including the code in builds which won't need it. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: drivers/net/zynq_gem.c
2016-05-24net: phy: dp83867: Add SGMII helper for configurationDan Murphy
The code assumed that if the interface is not RGMII configured then it must be SGMII configured. This device has the ability to support most of the MII interfaces. Therefore add the helper for SGMII and only configure the device if the interface is configured for SGMII. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add phy_interface_is_sgmii to phy.hDan Murphy
Add a helper to phy.h to identify whether the phy is configured for SGMII all variables. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Move is_rgmii helper to phy.hDan Murphy
Move the phy_interface_is_rgmii to the phy.h file for all phy's to be able to use the API. This now aligns with the Linux kernel based on commit e463d88c36d42211aa72ed76d32fb8bf37820ef1 Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: ti: Allow the driver to be more configurableDan Murphy
Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default. If devicetree is not used then use the default defines within the driver. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: dp83867: Add device tree bindings and documentationDan Murphy
Add the device tree bindings and the accompanying documentation for the TI DP83867 Giga bit ethernet phy driver. The original document was from: [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel] Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: zynq_gem: Add the passing of the phy-handle nodeDan Murphy
Add the ability to pass the phy-handle node offset to the phy driver. This allows the phy driver to access the DT subnode's data and parse accordingly. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: Add reading of DT phy-handle nodeDan Murphy
Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT. The phy-handle also needs to be stored and passed to the phy to access any phy data that is available. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: dra74_evm: enable eth driver modelMugunthan V N
Enable eth driver model for dra74_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_sk_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_sk_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_gp_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_gp_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: fix ethernet name with proper device addressMugunthan V N
Fix typo error for cpsw device name with proper device address Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: am4372: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: add support for reading mac address from efuseMugunthan V N
Different TI platforms has to read with different combination to get the mac address from efuse. So add support to read mac address based on machine/device compatibles. The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c done by Tony Lindgren. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix get mdio base and gmii_sel reg from DTMugunthan V N
Since dra7x platforms address bus is define as 64 bits to support LAPE, fdtdec_get_addr() returns a invalid address for mdio based and gmii_sel register address. Fixing this by using fdtdec_get_addr_size_auto_noparent() which will derive address cell and size cell from its parent. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ARM: omap5: add platform specific ethernet phy modes configurationsMugunthan V N
Add platforms specific phy mode configuration bits to be used to configure phy mode in control module. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix cpsw dp parse when num slaves as 1Mugunthan V N
On some boards number of slaves can be 1 when only one port ethernet is pinned out. So do not break when slave_index and num slaves check fails, instead continue to parse the next child. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ti_omap5_common: eth: do not define DM_ETH for splMugunthan V N
Since omap's spl doesn't support DM currently, do not define DM_ETH for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: core: device: add support to check dt compatible for a device/machineMugunthan V N
Provide an api to check whether the given device or machine is compatible with the given compat string which helps in making decisions in drivers based on device or machine compatible. Idea taken from Linux. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add PHY driver for mv88e61xx switchesKevin Smith
The previous mv88e61xx driver was a driver for configuring the switch, but did not integrate with the PHY/networking system, so it could not be used as a PHY by U-boot. This is a complete rework to support this device as a PHY. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: Remove unused mv88e61xx switch driverKevin Smith
No boards are using this driver. Remove in preparation for a new driver with integrated PHY support. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
2016-05-24Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-05-24ARM: zynq: Simplify zynq configurationMichal Simek
Extending Kconfig for adding new platform is a lot of work for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and remove all dependencies on TARGET_ZYNQ_* options including SPL. As a side-effect it also remove custom init folder for ps7_init_gpl.* files. Folder is chosen based on device-tree file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: marvell: Do not reset phy after negotiationMichal Simek
The patch "net: phy: do not read configuration register on reset" (sha1: a058052c358c3ecf5f394ff37def6a45eb26768c) was causing regression on zynq zc702 board where Marwell 88e1118 phy was resetted after negotiation was setup. Phy reset is done pretty early in phy_connect_dev() and doens't need to be called again in phy code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: Wire return value from phy_config()Michal Simek
Fix zynq_gem driver to handle error from phy_config correctly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24image: Add boot_get_fpga() to load fpga with bootmMichal Simek
Add function boot_get_fpga() which find and load bitstream to programmable logic if fpga entry is present. Function is supported on Xilinx devices for full and partial bitstreams in BIN and BIT format. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Remove additional blankline in image.h
2016-05-24net: phy: Handle phy_startup() error codes properlyMichal Simek
Propagate error code from genphy_update_link() to phy startup(). Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24phy: Return correct error code when timeout happensMichal Simek
Return -ETIMEDOUT if timeout happens. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24net: xilinx: Handle error value from phy_startup()Michal Simek
Handle error returned by phy_startup() properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24mkimage: Report information about fpgaMichal Simek
Add FIT_FPGA_PROP that user can identify an optional entry for fpga. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24fpga: Fix typo in function commentMichal Simek
Trivial patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Enable CLK frameworkMichal Simek
ZynqMP is using fixed clocks now that's why enabling it to be available for drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Add SPL support supportMichal Simek
Support RAM and MMC boot mode in SPL also with SPL_FIT images. In MMC boot mode two boot options are available: 1) Boot flow with ATF(EL3) and full U-Boot(EL2): aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000 -d bl31.bin atf.ub cp spl/boot.bin <sdcard fat partition> cp atf.ub <sdcard fat partition> cp u-boot.bin <sdcard fat partition> 2) Boot flow with full U-Boot(EL3): cp spl/boot.bin <sdcard> cp u-boot*.img <sdcard> 3) emmc boot mode dd if=/dev/zero of=sd.img bs=1024 count=1024 parted sd.img mktable msdos parted sd.img mkpart p fat32 0% 100% kpartx -a sd.img mkfs.vfat /dev/mapper/loop0p1 mount /dev/mapper/loop0p1 /mnt/ cp spl/boot.bin /mnt cp u-boot.img /mnt cp u-boot.bin /mnt cp atf.ub /mnt umount /dev/mapper/loop0p1 kpartx -d sd.img cp sd.img /tftpboot/ and program it via u-boot tftpb 10000 sd.img mmcinfo mmc write 10000 0 $filesize mmc rescan mmc part ls mmc 0 psu_init() function contains low level SoC setup generated for every HW design by Xilinx design tools. xil_io.h is only supporting file to fix all dependencies from tools. The same solution was used on Xilinx Zynq. The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which stays at the same location all the time. Bootrom expects starting address to be at 0xfffc0000 that's why this address is SPL_TEXT_BASE. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Add missing u-boot,dm-pre-reloc to DTSIMichal Simek
Add missing u-boot,dm-pre-reloc to get IPs initialized. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Align gic ranges for 64k in device treeAlexander Graf
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since commit 12e14066f we automatically deal with aliases GIC regions though, so we can map them transparently into guests even on 64kb page size systems. This patch makes use of that features and sets GICC and GICV to 64kb aligned and sized regions. Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24tools: zynqmpimage: Add Xilinx ZynqMP boot header generationMichal Simek
Add support for the zynqmpimage to mkimage. Only basic functionality is supported without encryption and register initialization with one partition which is filled by U-Boot SPL. For more detail information look at Xilinx ZynqMP TRM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24SPL: FIT: Enable SPL_FIT_LOAD in RAM based boot modeMichal Simek
Support loading FIT in SPL for RAM bootmode. CONFIG_SPL_LOAD_FIT_ADRESS points to address where FIT image is stored in memory. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-24ARM: zynq: Call ps7_post_config() for SPLMichal Simek
If ps7_post_config() is defined call it. It is enabling for example level shifters for PL bitstreams. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-27 15:01:11 +0000