| Age | Commit message (Collapse) | Author |
|---|
|
|
|
[trini: Migrate sama5d27_som1_ek_qspiflash/sama5d2_xplained_qspiflash
for CONFIG_ENV_SECT_SIZE]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The base of DRAM will be changed for the next generation SoC.
The addresses needed for booting the kernel should be shifted
according to the DRAM base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The base of DRAM will be changed for the next generation SoC.
Set the base address to the 'dram_base' environment variable, which
will be useful for scripting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The base of DRAM will be changed for the next generation SoC.
To support it along with existing SoCs in the single defconfig,
set 'loadaddr' at boot-time by adding the offset to the DRAM base.
CONFIG_SYS_LOAD_ADDR is still hard-coded for compilation, but the
value from environment variable 'loadaddr' should be used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For consistency with a function that will be added.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The base address of DRAM was 0x80000000 for all the ARM SoCs of this
family in the past. It will be changed to 0x20000000 for a planned new
SoC. To support multiple SoCs by the single uniphier_v8_defconfig, the
base must be run-time determined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, mem_map is hard-coded, and it worked well until the last
SoC. For a planned new SoC, the addresses of peripherals and DRAM
will be changed. Set it up run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Make this function work with any channel being empty.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, dram_init() code relies on the fact the DRAM size
configuration exists in the SG_MEMCONF register.
This will no longer be true for a planned new SoC, which will
replace SG_MEMCONF with a different register.
Refactor the hook in a more generic way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Until the last SoC, the register addresses have been hard-coded because
they are always constant. For a planned new SoC, the register bases
will be completely changed. I insist on supporting multiple SoCs/boards
by a single defconfig (uniphier_v8_defconfig) since duplicating similar
defconfig files is a maintenance burden. The base addresses must be
fixed-up at run-time somehow.
Previously, the board init code identified the SoC by reading out the
SG_REVISION register. This is much easier than parsing DT.
You cannot do it any more because the base address of SG will be
changed. The SG_REVISION register exists to read out the SoC ID, but
you never know its address before identifying the SoC. Oh well.
So, the possible solution is to parse the DT, and find out the node
with "*-soc-glue" compatible string. Then, sg_base is set to the value
of the "reg" property. The sc_base is set up likewise.
It is worth noting a pit-fall. Having sc_base and sg_base in the global
scope will make the life easier, but the global variables are poorly
supported before the relocation. In fact, the .bss section overwraps
with DT. Allocating them in the .bss section would break DT. So, I gave
dummy initializers to assign them in the .data section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The SC_* macros represent the address of SysCtrl registers.
For a planned new SoC, its base address will be changed.
Turn the SC_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The SG_* macros represent the address of SoC-glue registers.
For a planned new SoC, its base address will be changed.
Turn the SG_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The planned new SoC supports the SD boot mode. Detect and display it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The planned new SoC does not have SBC (System Bus Controller) block.
Make boot_is_swapped() an optional hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot initialize SBC
(System Bus Controller), which may not be really necessary.
Check the "socionext,uniphier-system-bus" node in DT run-time.
If and only if it is found and its "status" property is okay,
initialize the SBC block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot tries to get access
to the devices on the support card, which may not actually exist.
Check the DT and search for the on-board devices run-time. If the
nodes are not found in DT, then disable the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I also added comments for NAND clocks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is boolean logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Now that 64-bit SoCs of this SoC family no longer support SPL,
this Makefile can be slightly simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The .boot_device_fixup() is only called by SPL.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is a remnant of commit f89d6133eef2 ("configs: move
CONFIG_SPL_TEXT_BASE to Kconfig").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
[ Linux commit aa38571246c6ac279ebebd141157297bcb959d76 ]
The memory regions specified by /memreserve/ are passed to
early_init_dt_reserve_memory_arch() with nomap=false, so it is
not suitable for reserving memory for Trusted Firmware-A etc.
Use the more robust /reserved-memory node with the no-map property
to prevent the kernel from mapping it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add SPI controller driver implemented in Socionext UniPhier SoCs.
This controller has the SPI master mode only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
|
|
For a planned new SoC in this SoC family, the base address of the
DRAM will be changed from 0x80000000 to 0x20000000.
The PIE support will be useful to maintain multiple similar SoCs
whose DRAM addresses differ.
Now CONFIG_SYS_TEXT_BASE is not important. I just set it to 0
to ensure CONFIG_POSITION_INDEPENDENT is working.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
|
|
The previous pcf2127 RTC chip could not read and set the correct time.
When reading the data of internal registers, the read address was the
value of register plus 1. This is because this chip requires the host
to send a stop signal after setting the register address and before
reading the register data.
This patch sets the register address using dm_i2c_write and reads
the register data using the original dm_i2c_xfer in order to generate
a stop signal after the register address is set, and fixes the bug of
the original read and write time.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The spi-nor flash resides on spi bus 1. Update the CONFIG_ENV_SPI_CS
and CONFIG_BOOTCOMMAND accordingly.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[tudor.ambarus@microchip.com: amend the commit message.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Use the qspi memory layout defined in at91-sama5_common - it aligns
with the 8 Mbyte flash (sst26vf064b-104i/sn) available in sama5d27_som1_ek.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Add the default config file of QSPI media. The config is based on
sama5d27_som1_ek_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add the default config file of QSPI media. The config is based on
sama5d2_xplained_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Use the same memory layout as we use for the NAND boot on the other boards.
QSPI flashes are present on the following boards:
sama5d2_xplained RevB: 32 Mbyte flash (mx25l3273fm2i-08g)
sama5d2_xplained RevC: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d27_som1_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d2_ptc_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
The 8 Mbyte limit is enough to cope with the memory layout used in the NAND
boot. rootfs exceeds the 8 Mbyte limit and will stay in eMMC in the
sama5d2_xplained case. The final scope is to use a single memory layout for
all boot medias.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: change memory layout, add commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Fix the following:
- use "jedec,spi-nor" binding, we use jedec compatible flashes
- set bus width to 4, we use quad capable flashes
- differentiate bewteen data and clk and cs pins
- drop partions as we don't use them in u-boot.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: use "jedec,spi-nor", edit commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
We use a sst spi-nor flash memory on sama5d27_som1_ek. Select
the others for testing purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
We have a macronix spi-nor flash on sama5d2_xplained RevB and
a sst spi-nor flash on RevC. Select the rest for testing purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Backport the driver from linux v5.1-rc5 and adapt it for u-boot.
Tested on sama5d2_xplained Rev B with mx25l25635e spi-nor flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Prior to starting a new transfer, conditionally wait for bus to not
be busy.
Reinitialise controller as otherwise operation is not stable.
For reference, see linux kernel
commit 9656eeebf3f1 ("i2c: Revert i2c: xiic: Do not reset controller before every transfer")
hs: Fixed DOS line endings
added missing '\n'
Fixed git commit description style
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
Comparison should be against the actual message length, not loop index.
len is used for stopping while loop, pos is position in message.
stop should be sent when entire message is sent, not when
len and pos meet.
hs: fixed DOS line endings
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
Get clock rate from clock DM if CONFIG_CLK is enabled.
Otherwise, uses IC_CLK define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Before calling __dw_i2c_set_bus_speed(),
the I2C could already be set as ether enable or disable,
we should restore the original setting instead of enable i2c anyway.
This patch fix a bug happened in init function:
__dw_i2c_init(){
/* Disable i2c */
...
__dw_i2c_set_bus_speed(i2c_base, NULL, speed);
writel(slaveaddr, &i2c_base->ic_sar);
/* Enable i2c */
}
In this case, enable i2c inside __dw_i2c_set_bus_speed() function
will cause ic_sar write fail.
Signed-off-by: Jun Chen <ptchentw@gmail.com>
|
|
This allows to silence ubi and ubispl individually.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
|
|
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
|
|
Migrate the ubispl configuration for the omap3_igep00x0 and
am335x_igep003x boards to KConfig. Both boards were built with
SOURCE_DATE_EPOCH=0 and found to be equal before and after.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
|
|
Move the ubispl configuration to KConfig and drop them from the
whitelist.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
|
|
- drop CONFIG_ prefix from kconfig entry
- fix small compilation issue with CONFIG_UBI_SILENCE_MSG
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
|
|
Introduce KConfig CONFIG_ENV_UBI_VID_OFFSET to allow providing custom
VID header offsets for the environment on UBI.
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
|
|
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.
As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.
This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").
All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).
hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
Introduce the KConfig option CONFIG_ENV_UBI_VOLUME_REDUND for defining
the name of the UBI volume used to store the redundant environment.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
hs: get rid of stm32mp1* build errors
|
