summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-09-16spi: Add spi_write_then_readJagan Teki
Add support for SPI synchronous write followed by read, this is common interface call from spi-nor to spi drivers. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
2019-09-16spi: Kconfig: Unmark DEPRECATED for MXS_SPILukasz Majewski
MXS_SPI driver now partially converted into driver-model, so unmark the DEPRECATED option for the same. Signed-off-by: Lukasz Majewski <lukma@denx.de> [jagan: update the commit message] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16spi: soft_spi: Fix data abort if slave is not probedChristophe Kerello
In case spi_get_bus_and_cs callback is used, spi bus is first probed then slave devices are probed. To avoid a data abort in soft_spi probe function, we need to check that (slave != NULL). If slave is NULL, cs_flags and clk_flags will be initialized with respectively GPIOD_ACTIVE_LOW and 0. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-16spi: mvebu_a3700_spi: Fix clock prescale computationMarek Behún
The prescaler value computation can yield wrong result if given 0x1f at the beginning: the value is computed to be 0x20, but the maximum value the register can hold 0x1f, so the actual stored value in this case is 0, which is obviously wrong. Set the upper bound of the value to 0x1f with the min macro. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-09-15Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2019-09-14Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Assorted bugfixes
2019-09-14Merge branch '2019-09-13-ti-imports'Tom Rini
- Assorted K3 bugfixes. - Assorted DM enablements, dead code removal.
2019-09-14sh: r2dplus: Enable DHCP commandMarek Vasut
Enable the "dhcp" command as a minor convenience. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-09-14sh: r2dplus: Fix missing PCI rangeMarek Vasut
Add missing PCI range for translating DRAM to bus addresses. This fixes e.g. PCI NIC interface and allows network to work in QEMU. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-09-14sh: Fix SH4 build with GCC versions without -m4-nofpuMarek Vasut
Pass -m4 instead of -m4-nofpu to GCC versions which do not support the -m4-nofpu option. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-09-14sh: Fix incorrect linking with new binutilsMarek Vasut
Since binutils 2.30 , the resulting U-Boot binary was incorrectly linked against address 0 instead of text base, fix it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-09-13configs: am65x_hs_evm: Use FIT images when booting HS devicesAndrew F. Davis
HS devices use the FIT post processing step to authenticate boot images. Set the configured boot command to load FIT by default. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-09-13configs: ti: Add environment support commands for FIT loadingAndrew F. Davis
Some parts of these commands can be reused, add them to common files. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-09-13ARM: dts: dra74x: Fix iodelay configuration for mmc3Faiz Abbas
According to the latest am572x[1] and dra74x[2] data manuals, mmc3 default, hs, sdr12 and sdr25 modes use iodelay values given in MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is selected and correct iodelay values are configured. [1] http://www.ti.com/lit/ds/symlink/am5728.pdf [2] http://www.ti.com/lit/ds/symlink/dra746.pdf Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-09-13arm: k3: Use get_ti_sci_handle() where ever possibleLokesh Vutla
Instead of calling uclass apis everywhere, use get_ti_sci_handle() when ever ti_sci is needed. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-09-13arm: k3: Fix getting ti_sci handleLokesh Vutla
API get_ti_sci_handle() is relying on the device-tree node name to be "dmsc" for probing the ti_sci device. But with the introduction of debug messages for dmsc, the node name changed to dmsc@44083000. Because of this ti_sci is never probed cause a boot failure. Instead of relying on device-tree node name, use the first available firmware node for probing ti_sci. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-09-13ARM: omapl138_lcdk: Enable PinctrlAdam Ford
The single pinctrl supports the da8xx, so this patch enables pinctrl in U-Boot. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13ARM: omapl138_lcdk: Enable DM_GPIO and DM and GPIO CommandsAdam Ford
The da8xx GPIO driver is available with DM_GPIO support. This patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13ARM: omapl138_lcdk: Disable SPL_DM_USBAdam Ford
The USB was just recently enabled, so it is unlikely anyone is using it in SPL, so this patch removes it from SPL to further reduce the SPL code size. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13ARM: omapl138_lcdk: Remove dead codeAdam Ford
The header it littered with #ifdefs and #defines and that appear to be legacy associations to the older da850-evm and in some cases obsolete with either Kconfig or DM migrations. This patch removes these legacy references. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-09-13arm: am437x: cm-t43: Enable DM for MMC, USB, SPI, SPI_FLASH, enable BLKSuniel Mahesh
Enable driver model for USB, MMC, SPI and SPI_FLASH. Also enable BLK. This will remove the following compile warnings: ===================== WARNING ====================== This board does not use CONFIG_DM_MMC. Please update the board to use CONFIG_DM_MMC before the v2019.04 release. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. ==================================================== ===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. ==================================================== Target was compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-09-13arm: am437x: cm-t43: Add device tree, enable OF_CONTROLSuniel Mahesh
Add device tree from Linux for driver model conversion and enable OF_CONTROL. This will remove the following compile warning: ================================================== Device Tree Source is not correctly specified. Please define 'CONFIG_DEFAULT_DEVICE_TREE' or build with 'DEVICE_TREE=<device_tree>' argument =================================================== Target was compile tested, build was clean. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
2019-09-13soc: ti: k3-navss-ringacc: fix k3_nav_ringacc_ring_reset_dmaVignesh Raghavendra
In case dma_ring_reset_quirk is not set the k3_ringacc_ring_reset_dma will just exit without ring reset. Fix it, by adding ring reset call in case dma_ring_reset_quirk is not. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2019-09-13MAINTAINERS: Change fsl-qoriq, mpc86xx, mpc85xx maintainersPriyanka Jain
Change maintainers to Priyanka Jain for fsl-qoriq, mpc85xx Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-09-12Merge tag 'efi-2019-10-rc4-4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for v2019.10-rc4 (4) Fixes for the EFI_FILE_PROTOCOL: * correctly iterate over directories * correct Unicode conversion of file names * parameter checks
2019-09-12lx2160: Correct serdes frequency print.Meenakshi Aggarwal
Suffix serdes frequency print with MHz Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12armv8: ls1028a: Updated serdes configuration for 0x13BBHou Zhiqiang
In SerDes protocol 0x13BB, lane C was erroneously assigned to PCIE1, this is now updated to PCIE2 Fixes: 36f50b75238e ("armv8: ls1028a: Add other serdes protocal support") Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12armv8: fsl-layerscape: Fix typo in Layerscape PCIe config entryHou Zhiqiang
The correct config entry is CONFIG_PCIE_LAYERSCAPE and this typo results in skipping the fixup of Linux PCIe DT nodes. Also enable the fixup when Layerscape Gen4 controller driver is enabled. Fixes: 4da0e52c9dc0 (armv8: fsl-layerscape: fix config dependency for layerscape pci code) Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: lx2160aqds: add support for SerDes protocol 14Florin Chiculita
Add SerDes1 protocol 14 in the list of supported protocols. This configuration enables one high-speed 100G port and PCIe x4. Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: lx2160aqds: fix ethernet-phy compatible propertyFlorin Chiculita
The code that generates the compatible property concatenates the ethernet phy id and clause-compatible information without separating them with a comma, resulting into no ethernet phy driver getting loaded by Linux kernel. Suffix phy_id_compatible_str with comma to fix this Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: fsl: lx2160a: implement board_fix_fdtPankaj Bansal
lx2160a rev1 and rev2 SoC has different pcie controller. The pcie controller device tree node fields "compatible" and registers names needs to be updated accordingly This change in device tree is handled as part of fdt fixups. These changes would only be applied if the soc revision is not rev1. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12armv8: fsl-layerscape: Update I2C clock dividerChuanhua Han
By default, i2c input clock is programmed at platform clk / 2 in u-boot, but this is not correct for all the platforms, Update I2C clock divider's default values as per SoC (LS1012A, LS1028A, LX2160A and LS1088A). Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12watchdog: sp805_wdt: add expire_now methodThomas Schaefer
Add sp805_wdt_expire_now function. expire_now method is required by U_BOOT_DRIVER. Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com> Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12armv8: ls1028a: configure PMU's PCTBENR to enable WDTThomas Schaefer
The SP805-WDT module on LS1028A requires configuration of PMU's PCTBENR register to enable watchdog counter decrement and reset signal generation. The watchdog clock needs to be enabled first. Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com> Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12arm: dts: ls1028a-qds: define the MDIO MUXAlex Marginean
Add the device-tree structure describing the MUX in board dts. QDS board has an on-board RGMII PHY and 4 slots for extension cards. All these can be accessed over MDIO through a MDIO MUX controlled over I2C. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board/lx2160a: Fix MC firmware loading for SD bootPankaj Bansal
During boot, u-boot reads MC, DPL, DPC firmware from SD card and copies to DDR. Update DDR addresses to which these firmwares are copied as per memory map of these firmwares on SD-card so that isolation between the regions of various firmwares is maintained to avoid geting overwritten. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12configs/ls1012ardb,lx2160ardb,ls1028ardb: add esdhc hs200 configYinbo Zhu
Enable CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK and CONFIG_MMC_HS200_SUPPORT config for ls1012ardb, ls1012ardb, lx2160ardb in defconfig file Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12mmc: fsl_esdhc: Add emmc hs200 supportYinbo Zhu
Add eMMC hs200 mode for ls1028a, ls1012a, lx2160a. This increases eMMC performance. Tuning procedure is currently not supported. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12dts: armv8: add emmc hs200 support for ls1028ardbYinbo Zhu
Add emmc hs200 support for ls1028ardb Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12dts: armv8: add emmc hs200 support for lx2160ardbYinbo Zhu
Add emmc hs200 support for lx2160ardb Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12dts: armv8: add emmc hs200 support for ls1012ardbYinbo Zhu
Add emmc hs200 support for ls1012ardb Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12mmc: Kconfig: Add FSL_ESDHC_USE_PERIPHERAL_CLK optionYinbo Zhu
NXP fsl_esdhc controller supports two reference clocks: platform clock and peripheral clock Peripheral clock can provide higher clock frequency which is required to be used for tuning of SD UHS mode and eMMC HS200/HS400 modes. Peripheral clock is enabled by default by defining config option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes are supported. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12fsl-layerscape: Add fsl_esdhc peripheral clock supportYinbo Zhu
Add esdhc peripheral clock support for NXP layerscape platforms: LS1046ARDB, LS1043ARDB, LS1012ARDB, LS1028ARDB, LS1088ARDB, LX2160ARDB Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-11Merge tag 'u-boot-rockchip-20190912' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - add idbloader.img target for rockchip tpl+spl; - usb ehci/ohci: go on process if clock driver don't have clk_enable(); - remove clk_enable() for rockchip clock drivers; - add boot order for rockpro64
2019-09-11efi_loader: parameter checks EFI_FILE_PROTOCOL.SetInfo()Heinrich Schuchardt
We do not support volume label changes. No parameter checks are needed here. When the info for as file is changed the buffer must always contain a file name. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-11doc: lion_rk3368: use idbloader.img for rk3368Matwey V. Kornilov
Makefile now produces ready-to-deploy idbloader.img file. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-11doc: rockchip: use idbloader.img for rk3288, rk3328, rk3399Matwey V. Kornilov
Makefile now produces ready-to-deploy idbloader.img file. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-11rockchip, Makefile: add idbloader.img targetMatwey V. Kornilov
Many Rockchip platforms require the same u-boot deploy procedure when TPL and SPL both enabled. The following examples are taken from doc/README.rockchip and board/theobroma-systems/lion_rk3368/README: RK3288: ./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out cat ./spl/u-boot-spl-dtb.bin >> out sudo dd if=out of=/dev/mmcblk0 seek=64 RK3328: ./tools/mkimage -n rk3328 -T rksd -d ./tpl/u-boot-tpl.bin idbloader.img cat ./spl/u-boot-spl.bin >> idbloader.img sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64 RK3368: ./tools/mkimage -n rk3368 -T rksd -d tpl/u-boot-tpl.bin spl-3368.img cat spl/u-boot-spl-dtb.bin >> spl-3368.img dd if=spl-3368.img of=/dev/sdb seek=64 RK3399: ./tools/mkimage -n rk3399 -T rksd -d ./tpl/u-boot-tpl-dtb.bin out cat ./spl/u-boot-spl-dtb.bin >> out sudo dd if=out of=/dev/sdc seek=64 Here, we introduce generic idbloader.img target which is the TPL image followed by the SPL binary. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clean makefile for misc.cKever Yang
Use obj-$(config) instead of #ifdef $config to make the code looks clean, and move the misc_init for U-Boot proper only. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: not depends on TPL_BUILD for rk3188 makefile includingKever Yang
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add this again in parent Makefile, remove it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2024-12-29 19:44:25 +0000