summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-12mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driverChristophe Kerello
The driver adds the support for the STMicroelectronics FMC2 NAND Controller found on STM32MP SOCs. This patch adds the polling mode, a basic mode that do not need any DMA channels. Only NAND_ECC_HW mode is actually supported. The driver supports a maximum 8k page size. The following ECC strength and step size are currently supported: - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC based on Hamming) This patch has been tested on Micron MT29F8G08ABACAH4. Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
2019-04-12dt-bindings: mtd: stm32_fmc2: add STM32 FMC2 NAND controller documentationChristophe Kerello
This patch adds the documentation of the device tree bindings for the STM32 FMC2 NAND controller. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12spi: stm32_qspi: move to exec_opChristophe Kerello
We are facing issues in the driver since SPI NOR framework has moved on SPI MEM framework, and SPI NAND framework is not running properly with the current driver. To be able to solve issues met on SPI NOR Flashes and to be able to support SPI NAND Flashes, the driver has been reworked. We are now using exec_op ops instead of using xfer ops. Thanks to this rework, the driver has been successfully tested with: - mx66l51235l SPI NOR Flash on stm32f746 SOC - n25q128a SPI NOR Flash on stm32f769 SOC - mx66l51235l SPI NOR Flash on stm32mp1 SOC - mt29f2g01abagd SPI NAND Flash on stm32mp1 SOC Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12ARM: dts: Add STMFX gpio expander support for stm32mp157c-ev1Patrick Delaunay
Adds alias to set the pincontrol seq id. For STMFX gpio expander, force sequence number after the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX gpio bank sequence number. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Force pinctrl driver probe in board_init()Patrice Chotard
In order to insure that hog GPIOs are configured early during the boot process, force all pinctrl driver probing in board_init(). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12config: stm32mp15: Enable STMFX supportPatrick Delaunay
Activate PINCTRL_STMFX and needed part for generic pincontrol PINCTRL_FULL, PINCONF. Increase pre-reloc memory for MALLOC (needed for each DM pinconfig node). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driverPatrick Delaunay
This patch adds pinctrl/GPIO driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander. STMFX is an I2C slave controller, offering up to 24 GPIOs. The driver relies on UCLASS_PINCTRL and UCLASS_GPIO. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12ARM: dts: stm32mp1: Add adc nodesPatrice Chotard
Add adc related nodes. These nodes are used to detect the current supplied by USB type-C power in port on DK1 and DK2 boards. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12Board: stm32mp1: Add supply current boot informationPatrice Chotard
For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2: range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected If detected current is < 3A, red led is kept ON after blinking. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Update README filePatrice Chotard
Update README with DK1 and DK2 boards related informations Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12ARM: dts: stm32: Synchronize DT with kernel onePatrice Chotard
This patch synchronizes U-boot DT with kernel one This is based on https://patchwork.kernel.org/cover/10797115/ This patch adds initial support of STM32MP157 discovery boards: - Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1). This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios) and 512MB of DDR3. Several connections are available on this boards: 4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ... - Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2). This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a) and Murata wifi/BT combo is added. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: add NVM update support in fuse commandPatrick Delaunay
Add functions to read/update the non volatile memory of STPMIC1 (8 bytes-register at 0xF8 address) and allow access with fuse command (bank=1, word > 0xF8). For example: STM32MP> fuse read 1 0xf8 8 Reading bank 1: Word 0x000000f8: 000000ee 00000092 000000c0 00000002 Word 0x000000fc: 000000f2 00000080 00000002 00000033 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: dts: activate psci-1.0Patrick Delaunay
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for power off command; TF-A for stm32mp15x supports PSCI 1.0. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add command poweroffPatrick Delaunay
Activate the command poweroff by default for STM32MP1: - with PCSI from TF-A for trusted boot - with PMIC sysreset request for basic boot (SYSRESET_POWER) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12pmic: stpmu1: add power switch off supportPatrick Delaunay
Add sysreset support, and support power switch off request, needed by poweroff command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12regulator: stpmu1: update buck1 rangePatrick Delaunay
SW impact for Rev 1.2 of STPMIC1 in U-Boot: Buck converters output voltage change for Buck1 => Vdd min 0,725 to max 1,5V instead of 0.6V to 1.35V (see STPMIC1 datasheet / chapter 5.3 Buck converters) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: Replace OTP read by SHADOW readPatrick Delaunay
Replace STM32_BSEC_OTP() by STM32_BSEC_SHADOW() to increase read performance. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: shadow all the upper OTP (no secure) during bootPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: use device tree new compatiblePatrick Delaunay
Update bsec driver to use the device tree provided by Kernel. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: basic boot: SPL enable access to GPIOZ bankPatrick Delaunay
SPL need to set GPIOZ_SECCFGR = 0 to enable access to GPIOZ bank (open security). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: align serial number on bootromPatrick Delaunay
Always use upper case for serial number. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add syscfg initializationPatrick Delaunay
Initialize the system configuration for basic boot - update interconnect setting - disable pull-down for boot pin - enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI - activate I/O compensation Done by SSBL = TF-A for trusted boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add some syscon drivers for syscfg and etpzcPatrick Delaunay
Add SYSCON driver for syscfg and etpzc and reorder in alphabetics order Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: activated some configurationPatrick Delaunay
Add configuration useful for test - FIT support - MEMTEST - DFU - CACHE - TIME - TIMER Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update memory layoutPatrick Delaunay
Update the memory layout to be aligned with other platform and avoid overlap with 32MB Linux kernel (multiv7 image). + Kernel => 32MiB offset = 0xC2000000 and increase the bootm size to 32MiB + FDT => 64MiB offset = 0xc4000000 + SCRIPT => 65Mib offset = 0xc4100000 + PXESCRIPT => 66Mib offset = 0xc4200000 + SPLASHIMAGE => 67Mib offset = 0xc4300000 + RAMDISK => 68Mib offset = 0xc4400000 (not limited size) In sources/boot/u-boot/doc/README.distro + kernel_addr_r: A size of 16MB for the kernel is likely adequate. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable. + ramdisk_addr_r: It is recommended that this location be highest in RAM out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size and use any available RAM. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + scriptaddr: A size of 1MB for extlinux.conf is more than adequate. For suggestions on memory locations for ARM systems, you must follow the guidelines specified in Documentation/arm/Booting in the Linux kernel tree. And in sources/linux-stm32mp/Documentation/arm/Booting The zImage may also be placed in system RAM and called there. The kernel should be placed in the first 128MiB of RAM. It is recommended that it is loaded above 32MiB in order to avoid the need to relocate prior to decompression, which will make the boot process slightly faster. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: support forced boot modePatrick Delaunay
The boot mode can be forced by key press or by TAMP register, requested in kernel by syscon-reboot-mode tamp: tamp@5c00a000 { compatible = "simple-bus", "syscon", "simple-mfd"; reg = <0x5c00a000 0x400>; reboot-mode { compatible = "syscon-reboot-mode"; offset = <0x150>; /* reg20 */ mask = <0xff>; mode-normal = <0>; mode-fastboot = <0x1>; mode-recovery = <0x2>; mode-stm32cubeprogrammer = <0x3>; mode-ums_mmc0 = <0x10>; mode-ums_mmc1 = <0x11>; mode-ums_mmc2 = <0x12>; }; }; Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: activate FASTBOOT on eMMCPatrick Delaunay
activate Fastboot for eMMC on EV1 board (mmc1) $> sudo apt-get install android-tools-adb android-tools-fastboot $> fastboot -i 0x0483 getvar bootloader-version Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update bootcmdPatrick Delaunay
Clearly separate bootcmd for stm32mp1 board (bootcmd_stm32mp) and preboot management. That solve issue for fastboot continue command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: spl: hang with trace when DDR init failedPatrick Delaunay
When DDR initialization failed, print error message and stop the SPL execution. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: cosmetic: add comment on psci_migrate_info_type return valuePatrick Delaunay
Add explaination for the return value of psci_migrate_info_type: 2 = Trusted OS. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: cosmetic cleanup KconfigPatrick Delaunay
Cosmetic cleanup in mach-stm32mp Kconfig - remove duplicated SPL_DRIVERS_MISC_SUPPORT - update help for TARGET_STM32MP1 - set value for NR_DRAM_BANKS - remove one comment as DEBUG_UART is deactivated by default - include board Kconfig at the end of the file Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: spl: add spl_display_printPatrick Delaunay
SPL displays the board model from device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update print_cpuinfo()Patrick Delaunay
Display CPU part number and package information. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update boot mode managementPatrick Delaunay
- export the function get_bootmode() and reused it in spl code - manage uart instance by alias (prepare v4.19 binding) - solve issue on nand instance - restore console for uart boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add runtime information in environmentPatrick Delaunay
Set board name with the first dts compatible found in DT code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG The result with DEVICE_TREE=stm32mp157c-ev1 is: STM32MP> env print board=stm32mp1 board_name=stm32mp157c-ev1 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: display board informationPatrick Delaunay
Implement checkboard() function to display - the boot chain used: basic or trusted - the board compatible in device tree - the board identifier and revision, saved in OTP59 for ST boards Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: bsec: access with SMC for trusted bootPatrick Delaunay
As BSEC is secure aware, all register access need to be done by TF-A for TRUSTED boot chain, when U-Boot is executed in normal world. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add trusted boot with TF-APatrick Delaunay
Add support of trusted boot, using TF-A as first stage bootloader, The boot sequence is BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32 The TF-A monitor provides secure monitor with support of SMC - proprietary to manage secure devices (BSEC for example) - PSCI for power The same device tree is used for STMicroelectronics boards with basic boot and with trusted boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-10Merge branch '2019-04-09-master-imports-fs'Tom Rini
- test.py tests for mmc - ext4 symlink support and other fixes - ext4 block group descriptor sizing
2019-04-10test.py: Disable fsck for FAT tests for nowTom Rini
Currently enabling fsck on FAT16/FAT32 exposes that we have problems with: TestFsBasic.test_fs13[fat16] TestFsBasic.test_fs11[fat32] TestFsBasic.test_fs12[fat32] TestFsBasic.test_fs13[fat32] TestFsExt.test_fs_ext1[fat32] TestFsExt.test_fs_ext2[fat32] TestFsExt.test_fs_ext3[fat32] TestFsExt.test_fs_ext4[fat32] TestFsExt.test_fs_ext5[fat32] TestFsExt.test_fs_ext6[fat32] TestFsExt.test_fs_ext7[fat32] TestFsExt.test_fs_ext8[fat32] TestFsExt.test_fs_ext9[fat32] TestMkdir.test_mkdir6[fat16] TestMkdir.test_mkdir1[fat32] TestMkdir.test_mkdir2[fat32] TestMkdir.test_mkdir3[fat32] TestMkdir.test_mkdir4[fat32] TestMkdir.test_mkdir5[fat32] TestMkdir.test_mkdir6[fat32] TestUnlink.test_unlink1[fat16] TestUnlink.test_unlink2[fat16] TestUnlink.test_unlink3[fat16] TestUnlink.test_unlink4[fat16] TestUnlink.test_unlink5[fat16] TestUnlink.test_unlink6[fat16] TestUnlink.test_unlink7[fat16] TestUnlink.test_unlink1[fat32] TestUnlink.test_unlink2[fat32] TestUnlink.test_unlink3[fat32] TestUnlink.test_unlink4[fat32] TestUnlink.test_unlink5[fat32] TestUnlink.test_unlink6[fat32] TestUnlink.test_unlink7[fat32] This is because we don't update the "information sector" on FAT32. While in the future we should resolve this problem and include that feature, we should enable fsck for ext4 to ensure that things remain in good shape there. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-09Fix ext4 block group descriptor sizingBenjamin Lim
Ext4 allows for arbitrarily sized block group descriptors when 64-bit addressing is enabled, which was previously not properly supported. This patch dynamically allocates a chunk of memory of the correct size. Signed-off-by: Benjamin Lim <jarsp.ctf@gmail.com>
2019-04-09test/py: mmc: Add 'mmc read' performance checkMarek Vasut
Add option to the mmc rd test to check the duration of the execution of the mmc read command. This allows intercepting read performance regressions. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-09test/py: mmc: Add 'mmc info' testMarek Vasut
Add test for 'mmc info' subcommand. This tests whether the card information is obtained correctly and verifies the device, bus speed, bus mode and bus width. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-09test/py: mmc: Add 'mmc rescan' testMarek Vasut
Add test for 'mmc rescan' subcommand. This tests whether the system can switch to a specific card and then rescan the card. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-09test/py: mmc: Add 'mmc dev' testMarek Vasut
Add separate test for 'mmc dev' subcommand. This tests whether the system can switch to a specific card. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-09test/py: mmc: Factor out device selectionMarek Vasut
Factor out the 'mmc dev' call so it can be recycled by other tests. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-09fs: fat: fix reading non-cluster-aligned root directoryAnssi Hannula
A FAT12/FAT16 root directory location is specified by a sector offset and it might not start at a cluster boundary. It also resides before the data area (before cluster 2). However, the current code assumes that the root directory is located at a beginning of a cluster, causing no files to be found if that is not the case. Since the FAT12/FAT16 root directory is located before the data area and is not aligned to clusters, using unsigned cluster numbers to refer to the root directory does not work well (the "cluster number" may be negative, and even allowing it be signed would not make it properly aligned). Modify the code to not use the normal cluster numbering when referring to the root directory of FAT12/FAT16 and instead use a cluster-sized offsets counted from the root directory start sector. This is a relatively common case as at least the filesystem formatter on Win7 seems to create such filesystems by default on 2GB USB sticks when "FAT" is selected (cluster size 64 sectors, rootdir size 32 sectors, rootdir starts at half a cluster before cluster 2). dosfstools mkfs.vfat does not seem to create affected filesystems. Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Reviewed-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Tested-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>