summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-02-02Blackfin: setup bi_enetaddr for single netsMike Frysinger
For systems with CONFIG_NET_MULTI disabled, bi_enetaddr does not get setup based on $ethaddr, so set it up. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: cache core/system clock valuesMike Frysinger
Calculating the clocks requires a bit of calls to gcc math functions, so cache the values after the first run since they'll most likely never change once U-Boot is up and running. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: enable --gc-sectionsMike Frysinger
Start building all Blackfin boards with -ffunction-sections/-fdata-sections and linking with --gc-sections. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: dont check baud if it wont actually get usedMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: add driver for on-chip SPI controllerMike Frysinger
This fills out the SPI backend for the Blackfin on-chip SPI peripheral. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: only build post code when CONFIG_POSTMike Frysinger
Save some time by using CONFIG_POST in the Makefile rather than C files. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02Blackfin: bfin_mac: cleanup pointer/casts for aliasing issuesMike Frysinger
Redo how pointers are managed to get rid of ugly casts and strict pointer aliasing issues that are highlighted by gcc 4.3. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-02Blackfin: bfin_mac: convert CONFIG_BFIN_MAC_RMII to CONFIG_RMIIMike Frysinger
No point in having a Blackfin-specific define "CONFIG_BFIN_MAC_RMII" that does exactly the same thing as common "CONFIG_RMII". Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-02Blackfin: bfin_mac: use common debug()Mike Frysinger
Rather then defining our own DEBUGF(), just use the common debug(). Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-02Blackfin: bfin_mac: respect CONFIG_PHY_{ADDR,CLOCK_FREQ}Mike Frysinger
Rather than having the on-chip MAC hardcoded to phy address 1 and a speed of 2.5mhz, use these as defaults if the board doesn't specify otherwise. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-02Blackfin: bfin_mac: cleanup MII/PHY functionsMike Frysinger
Cleanup and rewrite the MII/PHY related functions so that we can reuse the existing common linux/miiphy.h code and hook into the `mii` command. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-02Blackfin: bfin_mac: set MDCDIV based on SCLKMike Frysinger
Rather than hardcoding MDCDIV to 24 (which is correct for ~125mhz SCLK), use the real algorithm so it gets set correctly regardless of SCLK. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-01Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-02-01Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2009-02-01Merge branch 'master' of git://git.denx.de/u-boot-ixpWolfgang Denk
2009-01-31ixp: move serial to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31ixp: move pci init in arm/board instead of cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31ixp: move pci drivers to drivers/pciJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31ixp: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31ixp: add missing os defineJean-Christophe PLAGNIOL-VILLARD
need by arm-elf toolchains and no impact on the arm-linux one Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-31ixp: remove the option to include the MicrocodeJean-Christophe PLAGNIOL-VILLARD
instead the board will have to load it from flash or ram which will be specified by npe_ucode env var Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-30ixp/npe: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29SX1: add hardware V2 supportJean-Christophe PLAGNIOL-VILLARD
In the V2 the 2 flash has been replace by one 32MB flash Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29SX1: Fix second flash mappingJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29SX1: add CONFIG_STDOUT_USBTTY to enable preboot stdout redirect to usbttyJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29move Samsung's board to board/samsungJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29move ARM Ltd. to vendor dirJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29ppc4xx: Clean up configuration file for Korat boardLarry Johnson
This patch updates the default environmental variables for the Korat PPC 440EPx board, and makes additional minor fixes. Signed-off-by: Larry Johnson <lrj@acm.org> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-29ppc4xx: Add variable "korat_usbcf" for Korat boardLarry Johnson
The new environment variable "korat_usbcf" selects the USB port used by the Korat board's CompactFlash controller. Signed-off-by: Larry Johnson <lrj@acm.org> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-28AVR32: macb - Search for PHY idGunnar Rangoy
This patch adds support for searching through available PHY-addresses in the macb-driver. This is needed for the ATEVK1100 evaluation board, where the PHY-address will be initialized to either 1 or 7. This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when enabled tells the driver to search for the PHY address. Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com> Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com> Signed-off-by: Olav Morken <olavmrk@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28Fix IP alignment problemOlav Morken
This patch removes volatile from: volatile IP_t *ip = (IP_t *)xip; Due to a bug, avr32-gcc will assume that ip is aligned on a word boundary when using volatile, which causes an exception since xip isn't aligned on a word boundary. Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com> Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com> Signed-off-by: Olav Morken <olavmrk@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28Marvell 88E1118 interrupt fixRon Madrid
This patch adjusts the LED control so that interrupt lines are not reading LEDs and effectively causing indefinite interrupts to the controller. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28net: smc911x.c: Add LAN9211 to chip_ids[] arrayStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28Move is_valid_ether_addr() to include/net.hMike Frysinger
Import the is_valid_ether_addr() function from the Linux kernel. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28net: Sort Makefile labelsMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
2009-01-2885xx: Fix compile breakage with sbc8540 and sbc8560Wolfgang Denk
This fixes an error which raises just a warning: sbc8560.c:250: warning: passing argument 2 of 'strmhz' makes integer from pointer without a cast Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-01-28SPD823TS: do not define CONFIG_CMD_ENVMike Frysinger
Since the SPD823TS board does not actually have any writable flash to save its environment, undefine CONFIG_CMD_ENV so the "saveenv" command is disabled. This fixes the build error: common/libcommon.a(cmd_nvedit.o): In function `do_saveenv': common/cmd_nvedit.c:557: undefined reference to `saveenv' make: *** [u-boot] Error 1 Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28OMAP3: Add Zoom1 board supportDirk Behme
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here: http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add Pandora supportDirk Behme
Add Pandora support. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add EVM boardDirk Behme
Add EVM board support. Signed-off-by: Manikandan Pillai <mani.pillai@ti.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add Overo boardDirk Behme
Add Overo board support. Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add common power code, README, and BeagleBoardDirk Behme
Add BeagleBoard support, common power code and README. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-28Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk
2009-01-28Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2009-01-2885xx: Fix compile breakage with MPC8540EVALKumar Gala
Configuring for MPC8540EVAL board... mpc8540eval.c: In function 'checkboard': mpc8540eval.c:53: error: invalid operands to binary / make[1]: *** [mpc8540eval.o] Error 1 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-28usb_scan_devices: fix output with no devicesBryan Wu
We should check the return of usb_new_device() so that if no USB device is found, we print out the right message rather than always saying "new usb device found". Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-28USB: Add high-speed (480Mb/s) to all USB related outputsStefan Roese
With this patch the USB related connection speed output ("usb tree" command and debug output) is now high-speed enabled. This patch also fixes a compilation warning when debugging is enabled. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-28USB: Add dcache support to the EHCI driverStefan Roese
This patch adds routines to handle (flush/invalidate) the dcache for the QH and qTD structures and data buffers. This is needed on platforms using this EHCI support with dcache enabled (like the MIPS VCT board port). Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-28USB: Add EHCI support for VCT EHCI controllerStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
generated by cgit (git 2.34.1) at 2024-12-29 13:27:10 +0000