summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-06-21ARM: Add macros.h to be used in assembler file.Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21MX31: Add NAND SPL for i.MX31.Magnus Lilja
This patch adds the NAND SPL framework needed to boot i.MX31 boards from NAND. It has been tested on a i.MX31 PDK board with large page NAND. Small page NANDs should work as well, but this has not been tested. Note: The i.MX31 NFC uses a non-standard layout for large page NANDs, whether this is compatible with a particular setup depends on how the NAND device is programmed by the flash programmer (e.g. JTAG debugger). The patch is based on the work by Maxim Artamonov. Signed-off-by: Maxim Artamonov <scn1874@yandex.ru> Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21ARM1136: Introduce CONFIG_PRELOADER macro.Magnus Lilja
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's in start.S. In preparation for adding support for NAND SPL the macro CONFIG_PRELOADER is introducted and replaces the CONFIG_ONENAND_IPL in start.S. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-06-21at91: unify nor boot supportJean-Christophe PLAGNIOL-VILLARD
the lowlevel init sequence is the same so unify it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21at91sam9263ek: add nor flash supportJean-Christophe PLAGNIOL-VILLARD
this will allow you to store use it for the env and to boot directly U-Boot from Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21at91: add support for the PM9261 board of Ronetix GmbHIlko Iliev
The PM9261 board is based on the AT91SAM9261-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9261.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21pm9263: use macro instead of hardcode value for the lowlevel_initJean-Christophe PLAGNIOL-VILLARD
optimize a few the RAM init Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21pm9263: lowlevel init updateJean-Christophe PLAGNIOL-VILLARD
move PSRAM init to pm9263.c this will allow us after to make the nor lowlevel_init generic Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-15Blackfin: move ALL += u-boot.ldr to blackfin_config.mkMike Frysinger
The way the ALL variable is used allows for config.mk's to add more targets themselves without having to clutter up the top level Makefile. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Blackfin: fix SPI flash speed define nameMike Frysinger
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Blackfin: enable -O2 in lib_generic/ for ADI/Bluetechnix boardsMike Frysinger
Building the compression code in lib_generic/ with -O2 rather than -Os gives a nice speed boost without too much code size increase. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Blackfin: bf548-ezkit: bump up monitor sizeMike Frysinger
The latest version of U-Boot got a bit fatter in the BSS section which caused overflows in the RAM region, so increase the monitor size. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flashVivi Li
The SPI flash layer is much stricter about sector usage than the eeprom layer we used to use, so update the env settings to better match the sector alignment of the flashes we use. Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Blackfin: bump up default JTAG console timeoutVivi Li
The debug tools that interface with the other side of the JTAG console got much slower when generalizing things, so bump up the default timeout value on the U-Boot side to cope. Hopefully at some point we can improve the debug tools to speed things back up. Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2009-06-15Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2009-06-15Blackfin: add jtagconsole helper scriptMike Frysinger
This script is similar to the netconsole script, but instead works with the JTAG console device driver that exists on Blackfin parts. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15Convert DM9000 driver for CONFIG_NET_MULTIRemy Bohmer
All drivers need to be converted to CONFIG_NET_MULTI. This patch converts the dm9000 driver. Signed-off-by: Thomas Smits <ts.smits@gmail.com> Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15net: Add Marvell Kirkwood gigabit ethernet driverPrafulla Wadaskar
This patch adds a egiga driver for the Marvell Kirkwood SoC's. Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed-by: Ronen Shitrit <rshitrit@marvell.com> Acked-by: Stefan Rose <sr@denx.de> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15DaVinci Network Driver Updatess-paulraj@ti.com
Different flavours of DaVinci SOC's have differences in their EMAC IP This patch does the following 1) Updates base addresses for DM365 2) Updates MDIO frequencies for DM365 and DM646x 3) Update EMAC wrapper registers for DM365 and DM646x Patch applies to u-boot-net git. the EMAC driver itself will be updated shortly to add support for DM365 and DM646x Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Subject: [PATCH] [repost] Standardize the use of MCFFEC_TOUT_LOOP as a ↵Richard Retanubun
udelay(1) loop counter. From 584b5fbd4abfc43f920cc1c329633e03816e28be Mon Sep 17 00:00:00 2001 From: Richard Retanubun <RichardRetanubun@RuggedCom.com> Date: Wed, 20 May 2009 18:26:01 -0400 Subject: [PATCH] Standardize the use of MCFFEC_TOUT_LOOP as a udelay(1) loop counter. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15A VLAN tagged DHCP request/discover is 4 bytes shortNorbert van Bolhuis
The problem is that BOOTP_SIZE uses ETHER_HDR_SIZE which is 14 bytes. If sending a VLAN tagged frame (when env variable vlan is set) this should be VLAN_ETHER_HDR_SIZE=18 which is what NetSetEther returns. Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Remove support for non-CONFIG_NET_MULTI on PPC4xx EMACBen Warren
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Switched davinci_emac Ethernet driver to use newer APIBen Warren
Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Initial cleanup of Davinci Ethernet driverBen Warren
Removed pointless #ifdefs Moved functions around in file in preparation for switch to newer API Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Moved Davinci Ethernet driver to drivers/netBen Warren
This driver has been renamed davinci_emac.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Marvell MV88E61XX Switch Driver supportPrafulla Wadaskar
Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported for:- default or router port vlan configuration led_init configuration mdip/n polarity reversal configuration Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed by: Ronen Shitrit <rshitrit@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15tsec: Add support for BCM5482S PHYZach LeRoy
Signed-off-by: Zach LeRoy <zleroy@xes-inc.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-14Blackfin: unify u-boot linker scriptsMike Frysinger
All the Blackfin linker scripts were duplicated across the board dirs with no difference save from the semi-often used ENV_IS_EMBEDDED option. So unify all of them in the lib_blackfin/ dir and for the few boards that need to embedded the environment directly, add a LDS_BOARD_TEXT define for them to customize via their board config file. This is much simpler than forcing them to duplicate the rest of the linker script. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: bf518f-ezbrd: enable SST SPI flash driverMike Frysinger
The BF51xF parts have an internal SST SPI flash, so make sure the driver is enabled by default so we can access it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: convert specific pre/post config headers to common methodMike Frysinger
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup common Blackfin board defines. The common method now is to use config.h, so convert blackfin-config-post.h to that. Rename the still Blackfin specific blackfin-config-pre.h to config-pre.h so the naming conventions at least line up. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: enable LZMA for all ADI boardsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: make default ADI env more flexibleMike Frysinger
Allow boards to easily override the root= and default bootcmd, allow people to tweak the file used in default bootcmds at runtime via one env var, and add a stock nandboot command. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: ibf-dsp561: new board portHoan Hoang
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: blackstamp: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: bf537-srv1: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: bf537-minotaur: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: bf537-pnav: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: cm-bf527: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: cm-bf548: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: tcm-bf537: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: cm-bf561: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: cm-bf537e: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: cm-bf533: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: new spibootldr commandMike Frysinger
Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes, so add a new 'spibootldr' command to take advantage of it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14Blackfin: support embedding the environment into loader files (LDRs)Mike Frysinger
For the most part, the Blackfin processor boots files in the LDR format rather than binary/ELF files. So we want to export the environment as a raw blob to the LDR utility so it can embed it at the right location. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14add %.c->%.i and %.c->%.s rulesMike Frysinger
The Linux kernel has some helper rules which allow you to quickly produce some of the intermediary files from C source. Specifically, you can create .i files which is the preprocessed output and you can create .s files which is the assembler output. This is useful when you are trying to track down header/macro expansion errors or inline assembly errors. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-14make sure toplevel $(SUBDIRS) is always declaredMike Frysinger
The $(SUBDIRS) variable is only declared when U-Boot has been configured, but it gets used all the time. In the non-configured case, it is used to generate a helpful error message, but it needs to be set properly for that to occur. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14allow boards to customize compiler options on a per-file/dir basisMike Frysinger
With our Blackfin boards, we like to build the compression routines with -O2 as our tests show a pretty good size/speed tradeoff. For the rest of U-Boot though, we want to stick with the default -Os as that is mostly control code. So in our case, we would add a line like so to the board specific config.mk file: CFLAGS_lib_generic += -O2 Now all files under lib_generic/ will have -O2 appended to their build. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-14Merge branch 'next' of ../masterWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-26 11:57:40 +0000