summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-02-12Blackfin: br4: new board portDimitar Penev
This adds support for the BR4 Appliance. It is a quad channel ISDN BRI board based on Blackfin BF537 CPU. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12Blackfin: add in/out le32 variantsMike Frysinger
These are rarely used, but the post code does currently, so add small redirect hacks for that. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12post: add blackfin to the post_time_ms listMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12Blackfin: bf537-stamp: drop board reset workaroundMike Frysinger
The bf537-stamp shouldn't need this SPI flash workaround. It was added by accident a long time ago through a convoluted series of steps which originated from a customer board (not the bf537-stamp). So drop it to keep people from incorrectly adding it to their own boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12Blackfin: pr1: new board portDimitar Penev
This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX. This board is Blackfin BF537 based. The schematics are not fully opened. Signed-off-by: Dimitar Penev <dpn@switchfin.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12arm, davinci: Add support for the Calimain board from OMICRON electronicsChristian Riesch
This patch adds support for the Calimain board from OMICRON electronics GmbH. The board features a Texas Instruments AM1808 SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and CS3. Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12Changes to move hawkboard to the new spl infrastructureSughosh Ganu
This patch moves hawkboard to the new spl infrastructure from the older nand_spl one. Removed the hawkboard_nand_config build option -- The spl code now gets compiled with hawkboard_config, after building the main u-boot image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard to reflect the same. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12arm, arm926ejs: Enable icache only if CONFIG_SYS_ICACHE_OFF is not definedChristian Riesch
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Add option CONFIG_SYS_EXCEPTION_VECTORS_HIGHChristian Riesch
The V bit of the c1 register of CP15 should not be cleared on DA850 SoCs since they have no valid memory at 0x00000000. This patch introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH that allows setting the correct value for the V bit. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Flush the data cache before disabling itSughosh Ganu
The current implementation invalidates the data cache before turning it off and causes problems on the hawkboard. See the discussion in http://lists.denx.de/pipermail/u-boot/2012-January/115212.html According to the ARM926EJ-S Technical Reference Manual, the cache should be flushed instead. Also fix the comments to match code. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Rebased and corrected commit message. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Do cpu critical inits only for boards that require itChristian Riesch
This patch reverts commit ca4b55800ed74207c35271bf7335a092d4955416 "arm, arm926ejs: always do cpu critical inits" since it impacts all arm926ejs based configurations and caused problems, e.g., with the hawkboard. Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines from the board configurations that need low level initialization. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12arm, davinci: Add lowlevel_init for SoCs other than DM644XChristian Riesch
The low level initialization code in arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S was written for DM644X SoCs only. This patch makes the lowlevel_init function in this file a dummy function for SoCs other than DM644X. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com> Cc: Sergey Kubushyn <ksi@koi8.net> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12ARMV7: Fix duplicate use of "b" parameter in ACTIM_CTRLA definitionPeter Barada
ACTIM_CTRLA macro errently passes "b" parameter to ACTIM_CTRLA_TRAS() instead of "c". To make usage more clear, replace all single-letter macro parameters with more descriptive parameter names. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-02-12omap3logic: Add missing GPMC pinmux for LAN92xx accessPeter Barada
The initial checkin dropped pinmux setup for GPMC pins A6-A10, D0-D7 and NCS1/2 necessary to access LAN92xx on Logic OMAP35x/DM37x modules. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-02-12OMAP4460: Reduce MPU clock speed from 920 to 700Aneesh V
We do not have thermal management or Smartreflex enabled at U-Boot level. So, it's better to stick to OPP100 for MPU instead of the OPP Turbo that is used now. Adjust the VDD_MPU accordingly. Tested-by: Sebastien Jan <s-jan@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com>
2012-02-12davinci: add support for printing clock frequencyHadli, Manjunath
add support for printing various clock frequency info found in SOC such as ARM core frequency, DSP core frequency and DDR frequency as part of bdinfo command. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
2012-02-12davinci: remove macro CONFIG_DISPLAY_CPUINFOHadli, Manjunath
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer required. This is because clock info will be printed as part 'bdinfo' command and also remove support print_cpuinfo() as it will no longer be called. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
2012-02-12doc: fix typosPeter Meerwald
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12omap3: fix comment typosPeter Meerwald
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12beagle: fix typosPeter Meerwald
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12AM3517: Changed default clock rate for AM3517Schuyler Patton
AM3517: Changed default clock rate for AM3517 Changed #define MPU_M_13_ES2 from 0x1F4 to 0x258, this allows the AM3517 to boot up at 600MHz instead of 500 MHz Signed-off-by: Schuyler Patton <spatton@ti.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@gmail.com> CC: Stefano Babic <sbabic@denx.de>
2012-02-12mcx: support for HTKW mcx boardIlya Yanok
This patch adds support for the HTKW mcx AM3517-based board. Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both NAND and MMC SPLs are supported. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-02-12ARM: omap3: Added Teejet mt_ventouxStefano Babic
The mt_ventoux board is a custom board using the Technexion TAM3517 module. The patch fixes also the mtdparts variable in the TAM3517 common configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Igor Grinberg <grinberg@compulab.co.il> CC: Tom Rini <tom.rini@gmail.com> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-02-12OMAP3: TAM3517: update ehci interfaceStefano Babic
Changed the EHCI interface using the ulpi framework. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-02-12OMAP4: ehci-omap: enable ehci-omap for panda boardsGovindraj.R
For panda initialise the mux pins for ehci usage and enable ehci in omap4_panda config file. Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12OMAP4: clock-common: Move the usb dppl configuration to new funcGovindraj.R
usb dpll configuration is done only part of non-essential dppl configuration however if CONFIG_USB_EHCI_OMAP is defined we may have to configure usb dpll's for proper functioning of usb modules. So move the usb dppl configuration to a new func. and utilise the same during essential dpll configuration. Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12OMAP3+: Clock: Adding ehci clock enablingGovindraj.R
Adding ehci clock enabling mechanism part of clock framework. When essential clocks are enabled during init phase usb host clocks can also be enabled from clock framework. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12ehci-omap: Clean up added ehci-omap.cGovindraj.R
Clean up added ehci-omap.c and make it generic for re-use across omap-soc having same ehci ip block. Also pass the modes to be configured from board file and configure the ports accordingly. All usb layers are not cache aligned, till then keep cache off for usb ops as ehci will use internally dma for all usb ops. * Add a generic common header ehci-omap.h having common ip block data and reg shifts. * Rename and modify ehci-omap3 to ehci.h retain only conflicting sysc reg shifts remove others and move to common header file. * pass the board data for beagle/panda accordinly to use ehci ports. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12ehci-omap: driver for EHCI host on OMAP3Ilya Yanok
Taken from Beagle code. Tested on mcx board (AM3517-based). Signed-off-by: Ilya Yanok <yanok@emcraft.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12usb: ulpi: Add omap-ulpi-view port supportGovindraj.R
Based on discussion from this thread [1]. Adding omap-view port that helps us in using the generic ulpi framework for any ulpi phy ops using the INSNREG05_ULPI viewport reg available on omap platform. Currently ehci ports are available on omap3/4 platforms so enable the same for beagle and panda, patch is tested on the same boards. Thanks to Igor Grinberg <grinberg@compulab.co.il> for reviewing the omap-ehci patches and suggesting this approach. [1]: http://www.mail-archive.com/u-boot@lists.denx.de/msg76076.html Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12usb: ulpi: Extend the existing ulpi framework.Govindraj.R
Extend the existing ulpi viewport framework to pass the port number information for any ulpi ops. Fix the usage of ulpi api's accordingly. Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12ARM: Convert spear3xx and spear6xx boards to boards.cfgAmit Virdi
Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de>
2012-02-12SMDK5250: Add ethernet supportChander Kashyap
This patch enable support for SMC911X based ethernet device. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12EXYNOS: SMDK5250: Add MMC SPL supportChander Kashyap
This patch adds support for MMC SPL booting. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12EXYNOS: Add SMDK5250 board supportChander Kashyap
SMDK5250 board is based on Samsungs EXYNOS5250 SoC. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12ARM: EXYNOS: Add support for Exynos5 based SoCsChander Kashyap
Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of SoCs. This patch adds the support for Exynos5. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macroChander Kashyap
CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4) architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ to make it generic for exynos architecture. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12TRATS: set gpio of UART correctlyMinkyu Kang
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
2012-02-12TRATS: use the generic watchdog timerMinkyu Kang
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: HeungJun, Kim <riverful.kim@samsung.com>
2012-02-12S5P: support generic watchdog timerMinkyu Kang
This patch adds support the generic watchdog timer for s5pc1xx and exynos4 Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: HeungJun, Kim <riverful.kim@samsung.com>
2012-02-12ORIGEN: remove duplicated MACH_TYPE defineMinkyu Kang
Since MACH_TYPE_ORIGEN is updated on mach-types, remove the MACH_TYPE_ORIGEN on config file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
2012-02-12ARMV7: Exynos4: Add support for TRATS boardHeungJun, Kim
This patch adds support for Samsung TRATS board Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12ARMV7: Exynos4: Add supoort power for Exynos4HeungJun, Kim
This patch adds power.h and SAMSUNG_BASE() macro for using Exynos4 power. Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12ARMV7: Exynos4: Add watchdog.h for Exynos4HeungJun, Kim
This patch add watchdog.h for Exynos4 Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12Origen: Select SCLKMPLL as FIMD0 parent clockChander Kashyap
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12Exynos: Fix ARM Clock frequency calculationChander Kashyap
Earliar ARM clock frequency was calculated by: MOUTAPLL/(DIVAPLL + 1) which is actually returning SCLKAPLL. It is fixed by calculating it as follows: ARMCLK=MOUTCORE / (DIVCORE + 1) / (DIVCORE2 + 1) Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12Exynos: PWM: Add TCMPB3 field in pwm structureChander Kashyap
Add TCMPB3 field in pwm structure, earliar this was res1. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12arm/km: checkpatch cleanupHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de>
2012-02-12arm/km: speed up i2c access for keymile boardsHolger Brunck
We don't need 3us delay for our i2c bus. Decrease it to 1us. It would also be possible to use 100ns in the future, but currently kirkwood has no ndelay implementation. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2012-02-12bugfix: all Marvell specific build fails due to undefined reference to ↵Prafulla Wadaskar
`get_ticks' after http://patchwork.ozlabs.org/patch/136415/ was applied. All Marvell build fails with below error common/libcommon.o: In function `cread_line': /home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_ticks' /home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_tbclk' /home/uboot/src/u-boot-arm/common/main.c:720: undefined reference to `get_ticks' The same is fixed for Kirkwood, ARMADA100, pantheon and orion5x SoCs Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
generated by cgit (git 2.34.1) at 2024-12-28 00:17:21 +0000